Barco Projector Cineversum 120 Quickstart Manual

							11. Powering on/off the Cine VERSUM System
11. POWERING ON/OFF THE CINE VERSUM SYSTEM
Getting started
After power, source and link cables have been installed, proceed to start up of the Cine VERSUM System.
Overview
• Powering ON the Cine VERSUM System
• Status of the System after powering up
• Display Info ’New Display’ and ’Lost Display’
Powering on/off
Powering on/off is understood to mean switching on (to standby mode) and OFF the modules by means of its own power switch.
11.1 Powering ON the Cine VERSUM System
How to switch ON
An order of powering up the modules is not important.
1. Press the Power switch on the Cine VERSUM Master (On Cine VERSUM Master, page 27).
2. Turn over the power switch of the Cine VERSUM 50 (if in the link) in the (I) position (ON state) (Cine VERSUM 50, page 12).
3. Press the Power switch on the Cine VERSUM 80 (if in the link) (Cine VERSUM 80, page 13).
4. Press the Power switch on the Cine VERSUM 120 (if in the link) (Cine VERSUM 120, page 29)
11.2 Status of the System after powering up
About status of the modules after powering up
The last status of the modules is determinative for the status after the respective power switches have been turned on.
The System, from operation mode, can be powered down, using the respective power switches (Case A) or the power down mode
(Case B). The power down mode switches the system in the standby mode. Also important is the status of the respective displays
in the link (On or Off).
When turning on the power switch of the respective modules, the modules return to the last status.
Status of the modules in the system (Case A)
Status modulesCine VERSUM Master, Cine VERSUM 50, Cine VERSUM 80 and
Cine VERSUM 120 in the operation mode.
The linked displays return to the operation mode also, if they have the individual status ’ON’ (Switching linked
displays To and Out Standby, page 89).
The graphical display on the Cine VERSUM Master indicates how to enter the menus and at the bottom line the selected source file.
CineVERSUM >To enter the menu
Press the button
or use the RCU
7 xga75_gs.c03 _________
Menu 11-1
R5976468 CINE VERSUM SYSTEM 0311200377 
						

							11. Powering on/off the Cine VERSUM System
Status of the modules in the system (Case B)
Status modulesCine VERSUM Master, Cine VERSUM 50, Cine VERSUM 80 and
Cine VERSUM 120 in standby mode.
Standby LED on Cine VERSUM MasterBlinks (0.2s on/2s Off)
Standby LED on Connected DisplayBlinks (0.2s on/2s Off)
(For Cine VERSUM 50, blinking is superposed on already lightning
up standby LED)
Display on Cine VERSUM MasterStart up menu (menu 11-2) preceded by messages indicating the
detected displays (menu 11-3).
CineVERSUM >To enter the menu
Press the button
or use the RCU
CineVERSUM _________
Menu 11-2
Message New display
CineVERSUM _________
Menu 11-3
11.3 Display Info ’New Display’ and ’Lost Display’
When appears ’New Display’?
With a powered up Cine VERSUM Master, each time a display is turned on (standby mode), a message ’New Display’ appears
on-screen and in the graphical display on the Master.
Message New display
CineVERSUM _________
Menu 11-4
When appears ’Lost Display’?
With a powered up Cine VERSUM Master, each time a display is turned off (with power switch), a message ’Lost Display’ appears
on-screen (on the active display) and in the graphical display on the Master.
78
R5976468 CINE VERSUM SYSTEM 03112003 
						

							11. Powering on/off the Cine VERSUM System
Message Lost display
CineVERSUM _________
Menu 11-5
R5976468 CINE VERSUM SYSTEM 0311200379 
						

							11. Powering on/off the Cine VERSUM System
80R5976468 CINE VERSUM SYSTEM 03112003 
						

							12. Image Projection after Powering Up
12. IMAGE PROJECTION AFTER POWERING UP
Overview
• Image Projection Using the Jog Dial on Cine VERSUM Master
• Image Projection Using the Remote Control
• Lamp Mode Set Up for Cine VERSUM 120 Only
Picture display can be started up using the selection wheel on the Cine VERSUM Master or using its Remote
Control.
12.1 Image Projection Using the Jog Dial on Cine VERSUM Master
How starting the image projection
1. Press the jog dial on the Cine VERSUM Master (On Cine VERSUM Master, page 27).
Menu on graphical display changes as follows: (menu 12-1)
2. Place the arrow, by rotating the jog dial, in front of the item ’Power Up’ (Always pointed at start up).
3. Press the jog dial to confirm.
The Cine VERSUM Master starts up, indicated by the message’Power up’ in the display. A few dots appear successively,
indicating the start up period, to disappear after started up. (menu 12-2)
The Cine VERSUM Master starts on its turn image projection ofthe source, displayed when powering down the system, on the
active linked displays. The file of the selected source is added to the menu (left-bottom). (menu 12-3)
CineVERSUM Master >POWER UP
ECONOMIC
CineVERSUM _________
Menu 12-1
Message >POWER UP
****
CineVERSUM _________
Menu 12-2
CineVERSUM >To enter the menu
Press the button
or use the RCU
7 xga75_gs.c03 _________
Menu 12-3
12.2 Image Projection Using the Remote Control
Way of starting image projection
Different keys on the remote control can be used for starting image projection. Make sure that the Remote control suits the address
of the Cine VERSUM Master or uses the common address.
• (A) Standby key: last selected source re-selected.
• (B) Source selection key: direct access to the desired source.
• (C) ADJ (Adjust) and ENTER key: last selected source re-selected.
How starting the image projection(Case A & B)
1. Press the standby key or a valid source selection key (On InfraRed Remote Control, page 30). The Cine VERSUM Master starts
up, indicated by the message ’Power up’ in the display (menu 12-2).
The Cine VERSUM Master starts operation mode and starts on its turn image projection on the active linked displays. In case of
pressing the standby key, the displayed image is the selected videosource when powering down the system before. The file of
the selected source is added to the menu (left-bottom)(menu 12-3).
R5976468 CINE VERSUM SYSTEM 03112003
81 
						

							12. Image Projection after Powering Up
How starting the image projection (Case C)
1. Press the ADJ or ENTER key (On InfraRed Remote Control, page 30). Menu on graphical display changes as follows –menu 12-1.
2. Press the cursor keys↑or↓to select item ’Power Up’ (arrow in front of item).
3. Press ENTER to confirm. The Cine VERSUM Master starts up, indicated by the message ’Power up’ in the display (menu 12-2).
The Cine VERSUM Master starts operation mode and starts on its turn image projection on the linked displays of the source
displayed when powering down the system before. The file of the selected source is added to the menu (left-bottom)menu 12-3).
12.3 Lamp Mode Set Up for Cine VERSUM 120 Only
Overview
• Lamp Mode Set Up Single/Dual (Image Settings menu)
• Lamp Mode Set Up Economic/Normal (Image Settings menu)
• Lamp mode/Power set up in Display Settings menu
About Lamp Mode for Cine VERSUM 120
The Cine VERSUM 120 is equipped with a dual lamp unit. This lamp unit can be programmed to work in a single or a dual lamp
mode as well as boosted in power from 200 W (Economic) to 250 W (Normal).
When a lamp fails in the dual lamp mode, the projector goes on with projection on the remaininglamp.
When programming Single mode, then the least used lamp will be ignited.
Lamp ’mode’ and ’power’ can be set up in the IMAGE SETTINGS and in the DISPLAY SETTINGS menu. Both
set ups overrule each other, except when forced lamp 1 or 2 has been chosen in the LAMP MODE menu.
12.3.1 Lamp Mode Set Up Single/Dual (Image Settings menu)
When forced lamp 1 or 2 has been set up, then, itemLAMP MODEin the Image Settings menu is replaced by
non-active ’Forced lamp 1 or 2’ item.
How to set up:
1. Enter the MAIN menu and scroll through the sub menus, using the jog dial or the Remote Control until the Image Settings menu
for the Cine VERSUM 120 is displayed. (image 12-1)
2. Select menu itemLAMP MODEand enter the lamp mode ’Single’ or ’Dual’ by pressing the jog dial or theENTERkey on the
Remote Control.
Note:Results of lamp switching from Single to Dual will take some time due to the ignition time of the second lamp.
3. Leaving the GUI, use theBACKitem in the menu or pressEXITkey on the Remote Control.
CineVERSUMImage  settings
Advanced Settings
Installation
Service
1 NO MODULE
2 NO MODULE
3 VIDEO [VIDEO]
4 NO MODULE
5 NO MODULE
6 NO MODULE
7 RGB-YUV [RGB]
8 NO MODULE
Shut Down
BackImage SettingsMaster
  Brightness
  Contrast
  Saturation
  Tint
Display
Back
Display List1 CV50  On
2 CV80 On
3 CV120 On
Back[Single/Dual]
Cine VERSUM r01
CV120
Main Menu/Image Settings/Display/CV80 or CV120 /Lamp Power
If the CV120 is the only display in the linkImage SettingsDisplay
  Brightness
  Contrast
  Gamma
  Color Temperature
  Primaries:[Projector]
  Lamp mode:[Single]
  Lamp Power:[Normal]
MasterBack
Image 12-1
Menu item Lamp Mode
82R5976468 CINE VERSUM SYSTEM 03112003 
						

							12. Image Projection after Powering Up
12.3.2 Lamp Mode Set Up Economic/Normal (Image Settings menu)
How to set up:
1. Enter the MAIN menu and scroll through the sub menus, using the jog dial or the Remote Control until the Image Settings menu
is displayed. (image 12-2)
2. Select menu itemLAMP POWERand enter the lamp mode ’Economic’ or ’Normal’ by pressing the jog dial or theENTERkey on
the Remote Control.
Note:To increase the lamp life time, enter the economic lamp power mode.
3. Leaving the GUI, use theBACKitem in the menu or pressEXITkey on the Remote Control.
CineVERSUMImage  settings
Advanced Settings
Installation
Service
1 NO MODULE
2 NO MODULE
3 VIDEO [VIDEO]
4 NO MODULE
5 NO MODULE
6 NO MODULE
7 RGB-YUV [RGB]
8 NO MODULE
Shut Down
BackImage SettingsMaster
  Brightness
  Contrast
  Saturation
  Tint
Display
Back
Display List1 CV50  On
2 CV80 On
3 CV120 On
Back[Economic/Normal]
Cine VERSUM r01
CV120
Main Menu/Image Settings/Display/CV80 or CV120 /Lamp Power
If the CV120 is the only display in the linkImage SettingsDisplay
  Brightness
  Contrast
  Gamma
  Color Temperature
  Primaries: [Projector]
  Lamp mode:[Single]
  Lamp Power:[Normal]
MasterBack
Image 12-2
Menu item Lamp Power
12.3.3 Lamp mode/Power set up in Display Settings menu
How to set up
1. Enter the MAIN menu and scroll through the sub menus, using the jog dial or the Remote Control until the Display Settings menu
for the Cine VERSUM 120 is displayed. (image 12-3)
2. Select itemLAMPand press jog dial orENTERkey to confirm.
Lamp menu is displayed, inclusive itemsMODEandPOWER.
3. To set up Lamp Power, select itemPOWERand press the jog dial or theENTERkey on the remote Control for ’Normal’ or
’Economic’ lamp power.
4. To set up the Lamp Mode, select itemMODESand press the jog dial or theENTERkey on the remote Control.
A lamp mode menu is displayed allowing 4 different possibilities. The active mode is preceded with a star. Select the mode you
desire and press the jog dial orENTERkey on the Remote Control to confirm.
- DUAL: both lamps will be ignited at start up (Can be overruled in the IMAGE SETTINGS menu).
- LEASTUSED(=SINGLE):leastusedlampofbothwillbeignitedatstartup(CanbeoverruledintheIMAGESETTINGS
menu).
- LAMP1: atstartup,Lamp1willbeforcedtoignite(CANNOTbeoverruledintheIMAGESETTINGSmenu).
- LAMP2: atstartup,Lamp2willbeforcedtoignite(CANNOTbeoverruledintheIMAGESETTINGSmenu).
5. Leaving the GUI, use theBACKitem in the menu or pressEXITkey on the Remote Control.
Cine VERSUM r01
Lamp  Modes: [Dual]
  Power: [normal]
Max run timeLamp 1
  Run time: 50
  Nr Strikes: 20
  Last power: 200W
Lamp 2
  Run time: 40
  Nr Strikes: 10
  Last power: 250W
Back
Lamp Mode  *Dual
   Least used
   Lamp 1
   Lamp 2
Back
[Normal/Economic]
Main Menu/Installation/Display List/CV120 /Lamp 
Display Settings Switch OFF
 Display Info
 Rename
 IR Address 009
 Diagnosis
 Orientation
 Test patterns
 Lens
 Lamp
BackDisplay List1 CV50  On
2 CV80 On
3 CV120On
Back
InstallationInput Slots
File Service
Display List
Internal Pattern
W hen no signal
Source Transition
OSD configuration
Language
Keystone
Global Keystone:Yes
Output: [Largest]
Default Input Balance
Back
Image 12-3
Menu item lamp
R5976468 CINE VERSUM SYSTEM 0311200383 
						

							12. Image Projection after Powering Up
84R5976468 CINE VERSUM SYSTEM 03112003 
						

							13. Projection Stop (Standby or Economic Standby mode)
13. PROJECTION STOP (STANDBY OR ECONOMIC
STANDBY MODE)
Overview
• Projection Stop Using the Selection Wheel
• Projection Stop Using the Remote Control
Economic Standby for the Cine VERSUM Master only: in this mode, the power dissipation is reduced and the
system stays operational for re-start of the system.
13.1 Projection Stop Using the Selection Wheel
How to stop image projection
1. Press the jog dial on the Cine VERSUM Master. Scroll through the menu by rotating the jog dial until item ’Shutdown’ is pointed.
(menu 13-1)
2. Press the jog dial to confirm. The Master starts the shutdown process indicated in the graphical display with the message ’Power
Down’. At the end, the system returns to startup screen. (menu 13-2)
The Master goes into standby mode and switches on its turn the linked displays into the standby mode (disabling image projec-
tion).
3. To switch the Cine VERSUM Master into the ’Economic Standby’,press the jog dial again. The graphical display indicates two
items, ’POWER UP’ and ’ECONOMIC’. (menu 13-4)
4. Scroll down in the menu by rotating the jog dial until item ’ECONOMIC’ is pointed (menu 13-4).
5. Press the jog dial gain to confirm.
The Cine VERSUM Master switches into the Economic mode, meaning into the lowest power dissipation. The lightning of the
graphical display is reduced to a minimumincluding the Zzzzz message. (menu 13-5)
CineVERSUM Image Settings
Advanced settings
Installation
Service
1 NO MODULE
2 NO MODULE
3 VIDEO [VIDEO]
4 NO MODULE
5 NO MODULE
6 NO MODULE
7 RGB-YUV [RGB]
8 NO MODULE
>Shutdown
7 xga75_gs.c03 Back
Menu 13-1
Message >POWER DOWN
7 xga75_gs.c03 _________
Menu 13-2
CineVERSUM >To enter the menu
Press the button
or use the RCU
7 xga75_gs.c03 _________
Menu 13-3
CineVERSUM Master POWER UP
>ECONOMIC
CineVERSUM _________
Menu 13-4
Message Zzzzzzzzz
7 xga75_gs.c03 _________
Menu 13-5
R5976468 CINE VERSUM SYSTEM 0311200385 
						

							13. Projection Stop (Standby or Economic Standby mode)
13.2 Projection Stop Using the Remote Control
Overview
• Direct System Shutdown (standby)
• System Shutdown (standby) via screen menu
13.2.1 Direct System Shutdown (standby)
The On Screen menus on the Cine VERSUM 50, Cine VERSUM 80 and Cine VERSUM 120are with respect to
content identic. Nevertheless, some items are specific for a display and are therefore grayed out if not ap-
plicable for that specific display. Make sure that the Remote control suits the address of the Cine VERSUM
Master or uses the common address.
How to stop image projection
1. Point the front of the Remote Control (to the IR receiver of the Cine VERSUM Master, Cine VERSUM 80, Cine VERSUM 50, Cine
VERSUM 120 or the projection screen. The latter reflects the signal from the Remote Control. However, the effective distance
of the signal may differ due to the screen material.
2. Press for a few seconds the standby key on the Remote control (On InfraRed Remote Control, page 30).
On the screen appears a message, indicating the start of the power down process.
After a few seconds, the Cine VERSUM Master goes into standby mode and switches on its turn the active linked displays into
the standby mode (disabling image projection). (menu 13-6)
MESSAGE
POWER DOWN
Menu 13-6
13.2.2 System Shutdown (standby) via screen menu
How to stop image projection
1. Point the front of the Remote Control (to the IR receiver of the Cine VERSUM Master, Cine VERSUM 80, Cine VERSUM 50, Cine
VERSUM 120 or the projection screen. The latter reflects the signal from the Remote Control. However, the effective distance
of the signal may differ due to the screen material.
2. Press the ’ADJ’or’ENTER’ key on the Remote Control (On InfraRed Remote Control, page 30).
On the screen appears the main menu. (menu 13-7)
3. Scroll through the items, using the arrow keys↑or↓, until item ’Shutdown’ is highlighted (menu 13-7).
4. PressENTERto confirm.
On the screen appears a message, indicating the start of the power down process.
After a few seconds, the Cine VERSUM Master goes into standby mode and switches on its turn the active linked displays into
the standby mode (disabling image projection). (menu 13-8)
Cine VERSUM System
Image Settings
Advanced Settings
Installation
Service
1 NO MODULE
2 NO MODULE
3 VIDEO [VIDEO]
4 NO MODULE
5 NO MODULE
6 NO MODULE
7 RGB-YUV [RGB]
8 NO MODULE
Shutdown
Back
Menu 13-7
MESSAGE
POWER DOWN
Menu 13-8
86R5976468 CINE VERSUM SYSTEM 03112003