Barco Projector Cineversum 120 Quickstart Manual

							BARCOPROJECTION
Cine VERSUM 50
Cine VERSUM Master
Digital Link
Cine Versum 120
Cine Versum 80
CINEVERSUM SYSTEM
R9841020 Cine VERSUM Master/R9001870/R9005010 - R9001870 Cine VERSUM 80
R9005010 Cine VERSUM 50 - R9010090 Cine VERSUM 120
INSTALLATIONMANUAL
03112003R5976468/01 
						

							Barco nv Home Cinema
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.84.30
Fax: +32 56.36.88.62
E-mail:[email protected]
Visit us at the web: www.homecinema.barco.com
Printed in Belgium 
						

							Copyright ©
All rights reserved. No part of this documentmay be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of BARCO.
Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war-
ranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the
program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this
publication; these changes are incorporated in new editions of this publication.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarksor copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufactures.
Federal Communication Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user is encouraged to tryto correct the interference by one or more of the following measures.
Introduction to the user :
If this equipment does cause interference to radio or television reception, the user may try to correct the interference by one or more of the
following measures :
• Re-orientation of the receiving antenna for the radio or television.
• Relocate the equipment with respect to the receiver.
• Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits.
• Fasten cables connectors to the equipment by mounting screws.
The use of shielded cables is required to comply within the limits of Part 15 of FCC rules and EN55022.
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser
must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco
must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning,
at latest 30 days after the transfer of risks. In the event of justified notice of compliant, Barco can repair the fault or provide a replacement
at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a
reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or
indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component
of the system or independent service, will be deemed invalid provided the damage is not proven tobe attributed to the absence of properties
guaranteed in writing or due to the intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly,
in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not
agreed upon in the contract, all guarantee claims of the purchaser willbe rendered invalid. Not included in the guarantee coverage are
system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as
well as normal maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in the this manual must be complied with by
the customer. 
						

							Table of contents
TABLE OF CONTENTS
1. Safety Instructions .................................................................................................. 51.1 General Safety Instructions ............................................................................................................. 5
1.1.1 General Instructions . ............................................................................................................. 5
1.1.2 Electrical Safety .................................................................................................................. 6
1.1.3 Protection on Servicing........................................................................................................... 6
1.1.4 Safety on Cleaning . . ............................................................................................................. 7
1.1.5 Safety on Shipping ............................................................................................................... 7
1.2 Display Related Safety Instructions .................................................................................................... 7
1.2.1 Cine VERSUM 50 ................................................................................................................ 7
1.2.1.1 On installation site ......................................................................................................... 7
1.2.1.2 On product specifications.................................................................................................. 8
1.2.2 Cine VERSUM 80 and Cine VERSUM 120 ..................................................................................... 8
1.2.2.1 Heat and Fire Hazards .................................................................................................... 8
1.2.2.2 Safety on Installation ...................................................................................................... 9
1.2.2.3 Protection from High Intensity Light Beam and Ultraviolet Radiation.................................................... 9
2. Cine VERSUM System............................................................................................. 112.1 Digital Video Distribution Concept..................................................................................................... 11
2.2 Digital Video Distribution Parts ........................................................................................................ 11
2.2.1 Cine VERSUM Master ..........................................................................................................12
2.2.2 Cine VERSUM 50 ...............................................................................................................12
2.2.3 Cine VERSUM 80 ...............................................................................................................13
2.2.4 Cine VERSUM 120..............................................................................................................13
2.2.5 Digital Link ....................................................................................................................... 13
3. Unpacking ...........................................................................................................153.1 Unpacking Cine VERSUM Master..................................................................................................... 15
3.2 Unpacking Cine VERSUM 80 ......................................................................................................... 16
3.3 Unpacking Cine VERSUM 120 ........................................................................................................ 17
3.4 Unpacking Cine VERSUM 50 ......................................................................................................... 18
4. Dimensions..........................................................................................................194.1 Cine VERSUM Master ................................................................................................................. 19
4.2 Cine VERSUM 80...................................................................................................................... 21
4.3 Cine VERSUM 120 .................................................................................................................... 23
4.4 Cine VERSUM 50...................................................................................................................... 24
5. Location of Controls...............................................................................................275.1 On Cine VERSUM Master ............................................................................................................. 27
5.2 On Cine VERSUM 50.................................................................................................................. 27
5.3 On Cine VERSUM 80.................................................................................................................. 28
5.4 Cine VERSUM 120 .................................................................................................................... 29
5.5 On InfraRed Remote Control .......................................................................................................... 30
6. Installation Guidelines.............................................................................................336.1 Projector Installation Guidelines....................................................................................................... 33
6.1.1 General Installation Guidelines ................................................................................................. 33
6.1.2 Image Projection ................................................................................................................ 34
6.1.2.1 Cleaning the lens .........................................................................................................34
6.1.2.2 Image Projection configurations.......................................................................................... 34
6.1.2.3 Projector distance adjustment............................................................................................ 36
6.1.2.4 Projector installation requirements .......................................................................................38
6.1.2.5 Lens Control ..............................................................................................................38
6.1.2.6 Ceiling Mount for Cine VERSUM 80 Cine VERSUM 120 ............................................................... 40
6.2 Plasma Screen Installation Guidelines................................................................................................ 41
6.2.1 About Installation of the Unit.................................................................................................... 41
6.2.2 Installation using the Wall mount kit............................................................................................ 41
6.2.3 Installation using the Table mount kit ........................................................................................... 42
7. Connections.........................................................................................................457.1 Power Supply Connection . ............................................................................................................ 45
7.1.1 Supplied Power Cords . . . . . ..................................................................................................... 45
7.1.2 Power Connection Cine VERSUM Master..................................................................................... 45
7.1.3 Power Connection Cine VERSUM 80 . . . . ...................................................................................... 46
7.1.4 Power Connection Cine VERSUM 120 . . . ...................................................................................... 47
7.1.5 Power Connection Cine VERSUM 50 . . . . ...................................................................................... 47
7.2 Connection for Preview and Communication . . . ...................................................................................... 48
7.2.1 Connection for Preview Monitors . . ............................................................................................. 48
7.2.2 Connection for Communication ................................................................................................. 49
7.2.3 Network Connection . ............................................................................................................ 50
7.3 Digital Link to Display Modules . . . ..................................................................................................... 51
7.3.1 Cine VERSUM System Link .................................................................................................... 51
7.3.2 Digital Link to One Display ...................................................................................................... 52
R5976468 CINE VERSUM SYSTEM 03112003
1 
						

							Table of contents
7.3.3 Digital Link to More Displays (Loop-through) . .................................................................................. 53
7.3.4 Digital Link Cable for long distances............................................................................................ 54
7.4 Connection to Video Equipment....................................................................................................... 55
7.4.1 Input Connection per Module . . ................................................................................................. 56
7.4.2 Installation of an Input module . ................................................................................................. 58
8. Operating the Remote Control ...................................................................................618.1 Battery Insertion in the Remote Control............................................................................................... 61
8.2 Operating the Remote Control......................................................................................................... 62
8.3 Address setting for the Remote Control............................................................................................... 63
9. Points of Similarity between Graphical display and On Screen Menus ..................................659.1 Explanation about differences in menu displays ...................................................................................... 65
10.Overview GUI Menu Screens.....................................................................................6910.1Overview Main menu .................................................................................................................. 69
10.2Overview Image Settings.............................................................................................................. 70
10.3Overview Advanced Settings.......................................................................................................... 71
10.4Overview Installation .................................................................................................................. 72
10.5Overview Service ...................................................................................................................... 75
11.Powering on/off the Cine VERSUM System ...................................................................7711.1Powering ON the Cine VERSUM System ............................................................................................ 77
11.2Status of the System after powering up............................................................................................... 77
11.3Display Info ’New Display’ and ’Lost Display’......................................................................................... 78
12.Image Projection after Powering Up ............................................................................8112.1Image Projection Using the Jog Dial on Cine VERSUM Master ..................................................................... 81
12.2Image Projection Using the Remote Control ......................................................................................... 81
12.3Lamp Mode Set Up for Cine VERSUM 120 Only..................................................................................... 82
12.3.1Lamp Mode Set Up Single/Dual (Image Settings menu)...................................................................... 82
12.3.2Lamp Mode Set Up Economic/Normal (Image Settings menu) ............................................................... 83
12.3.3Lamp mode/Power set up in Display Settings menu. . . . ....................................................................... 83
13.Projection Stop (Standby or Economic Standby mode).....................................................8513.1Projection Stop Using the Selection Wheel........................................................................................... 85
13.2Projection Stop Using the Remote Control ........................................................................................... 86
13.2.1Direct System Shutdown (standby)............................................................................................. 86
13.2.2System Shutdown (standby) via screen menu................................................................................. 86
14.Switching linked displays To and Out Standby...............................................................8914.1Switching by means of the Cine VERSUM Master . .................................................................................. 89
14.1.1Switching In/Out Standby using the Jog Dial. .................................................................................. 89
14.1.2Switching In/Out Standby using the Remote Control . . . ....................................................................... 90
14.2Direct Switching of the Linked Display................................................................................................ 91
14.2.1Switching a specific display In/Out standby....................................................................................91
15.Module Address Read out/Change..............................................................................9315.1Default address of the Modules . . ..................................................................................................... 93
15.2Reading out/Changing the stored addresses . . . ...................................................................................... 93
15.2.1Reading out the stored address................................................................................................ 93
15.2.2Changing the stored addresses................................................................................................ 94
16.Input Source File Service.........................................................................................9716.1About Stored files...................................................................................................................... 97
16.2Loading a File.......................................................................................................................... 97
16.3Editing a File........................................................................................................................... 99
16.4File identification . . . .................................................................................................................... 99
16.5Rename a file.........................................................................................................................102
16.6Copy a file.............................................................................................................................102
16.7Delete a file ...........................................................................................................................103
16.8Delete all files.........................................................................................................................104
16.9File options............................................................................................................................104
17.Adjusting the Picture ............................................................................................ 10517.1Setup Video and RGB module for the input signal type .............................................................................105
17.2Adjusting the Image Orientation......................................................................................................106
17.3Adjusting the Image Aspect Ratio....................................................................................................107
17.4Adjusting the Decoding Standard ....................................................................................................109
17.5White Peak Set up....................................................................................................................109
17.6Keystone Correction..................................................................................................................110
17.6.1Setting the Keystone correction: Global or on a File .........................................................................110
17.6.2Applying the Keystone correction.............................................................................................. 111
17.7Adjusting the Image Shift and Size ..................................................................................................112
17.7.1Adjusting the Image Shift ......................................................................................................112
17.7.2Adjusting the Image Size ......................................................................................................113
17.8Outline the displayed Image (Blanking)..............................................................................................113
2
R5976468 CINE VERSUM SYSTEM 03112003 
						

							Table of contents
17.9Alignment of the Input Balance . . ....................................................................................................114
17.9.1Input Balance Selection . . . . ....................................................................................................115
17.9.2Input Balance Adjustment. . ....................................................................................................116
17.10Phase adjustment for Computer signals ...........................................................................................117
17.11Gamma Correction ..................................................................................................................117
17.12Adjusting the Color Temperature ...................................................................................................118
17.12.1Selecting the preset Color Temperature .....................................................................................119
17.12.2Customizing the Color Temperature .........................................................................................120
17.13Adjusting the Picture Controls ......................................................................................................122
17.13.1Master Adjustment of the Analog Controls ..................................................................................123
17.13.2Analog Controls adjustment per Display.....................................................................................123
17.13.2.1Via Cine VERSUM Master .............................................................................................124
17.13.2.2Via Display with Remote Control only .................................................................................125
18.Additional settings Cine VERSUM Master ................................................................... 12718.1Output Resolution set up .............................................................................................................127
18.2Display Internal Generated Pattern . . ................................................................................................128
18.3Shutdown Automatic when no signal ................................................................................................129
18.4Source Transition.....................................................................................................................130
18.5On Screen Display Configuration ....................................................................................................130
18.5.1About the OSD (Menu, Bar Scale and Message) .............................................................................130
18.5.2Status Change of the OSD ....................................................................................................131
18.5.3On Screen Display Position Alignment........................................................................................132
18.6On-Screen Display Language . . . . ....................................................................................................132
18.7Display Name Change ...............................................................................................................133
19.Picture in Picture (PIP) .......................................................................................... 13519.1Turning On/Off the Picture in Picture ................................................................................................135
19.2Selecting Input Source for PIP Window. . ............................................................................................135
19.3Configuration of the PIP Window ....................................................................................................136
20.Cine VERSUM Master Settings & Info ........................................................................ 13920.1Service Menu .........................................................................................................................139
20.2Cine VERSUM Master Identification . ................................................................................................139
20.3Cine VERSUM Master Password ....................................................................................................140
20.4Cine VERSUM Master Address......................................................................................................141
20.4.1About the Cine VERSUM Master Address....................................................................................141
20.4.2Cine VERSUM Master Address change . .....................................................................................142
20.4.3Selecting the Transmission Speed ............................................................................................143
20.4.4Selecting the Interface standard (RS232/RS422).............................................................................143
20.4.5RS422 data bus termination ...................................................................................................144
20.4.6Diagnosis . . . . ...................................................................................................................144
21.Maintenance Indicators ......................................................................................... 14521.1Display Information ...................................................................................................................145
21.2Display Diagnosis. . ...................................................................................................................147
21.3ColorWheel IndexCine VERSUM 80 . ................................................................................................148
21.4Test Pattern ...........................................................................................................................149
Index.................................................................................................................... 153
R5976468 CINE VERSUM SYSTEM 031120033 
						

							Table of contents
4R5976468 CINE VERSUM SYSTEM 03112003 
						

							1. Safety Instructions
1. SAFETY INSTRUCTIONS
Overview
• General Safety Instructions
• Display Related Safety Instructions
1.1 General Safety Instructions
Overview
• General Instructions
• Electrical Safety
• Protection on Servicing
• Safety on Cleaning
• Safety on Shipping
1.1.1 General Instructions
Scope
This document includes safety considerations of the Cine VERSUM System. Throughout this manual, the term SERVICE PERSON-
NEL refers to persons having appropriate technical training and experience necessary to be knowledgeable of potential hazards
to which they are exposed (including, but not limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY and HIGH
BRIGHTNESS PROJECTORS) in performing a task, and of measures tominimize the potential risk to themselves or other persons.
The term USER and OPERATOR refers to any person other than SERVICE PERSONNEL, AUTHORIZED to operate the installed
digital video distribution system.
General safety instructions
• Before operating your digital video distribution system, please read this manual thoroughly, and retain it for future use.
• Installation and preliminary adjustments should be performed by qualified BARCO service personnel or authorized BARCO
service dealers.
• All warnings on the system parts and in the documentation manual should be adhered to.
• All instructions for operating and use of this equipment must be followed precisely.
• All local installation codes should be adhered to.
Owner’s Record
The part number and serial number are indicated on the registration plate which is located at the rear of the Cine VERSUM 50, at
the bottom of the Cine VERSUM Master, Cine VERSUM 80 and Cine VERSUM 120. Record these numbers in the spaces of the
table provided below. Refer to them whenever you call upon your BARCO dealer regarding these products.
NameParts NumberSerial NumberDealer
Cine VERSUM Master
Cine VERSUM 50
Cine VERSUM 80
Cine VERSUM 120
R5976468 CINE VERSUM SYSTEM 031120035 
						

							1. Safety Instructions
Shock Hazard
The lightning flash with an arrowhead within a triangle is intended to tell the user that 
parts inside this product are risk of electrical shock to persons.
The exclamation point within a triangle is intended to tell the user that important 
operating and/or servicing instructions are included in the technical documentation f
othis equipment.
Image 1-1
1.1.2 Electrical Safety
Ratings & Grounding
• These products should be operated from an AC power source. Check if the mains voltage and the load matches the product
electrical ratings.
• A grounded three-core power cable has to be used. Connect the power cord by inserting it in a grounded electrical outlet,
making sure that the cord is properly grounded.
• If you are unable to install the AC Requirements, contact your electrician. Do not defeat the purpose of the grounding.
• Always connect this appliance to an electrically grounded outlet. Never use a ground bypass (cheater) adapter.
General
• Always plug power cord into appliance before plugging into outlet.
• Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord.
• Always unplug appliance from electrical outlet before cleaning and servicing and when not in use. Never yank cord to pull plug
from outlet. Grasp plug and pull to disconnect.
• Do not operate appliance with a damaged cord or if the appliance has been dropped or damaged - until it has been examined
by a qualified serviceman.
• Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
• If an extension cord is necessary, a cord with a current rating atleast equal to that of the appliance should be used. Cord rated
for less amperage than the appliance may overheat.
• Let appliance cool completely before storing. Remove cord from appliance when storing.
• Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out
parts that could result in a risk of fire or electrical shock.
• Never spill liquid of any kind on the product. Should any liquid or solid object fall into the cabinet, unplug the set and have it
checked by qualified service personnel before resuming operations.
• Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet. This will prevent damage to the projector due to lightning and AC power-line
surges.
1.1.3 Protection on Servicing
Attempts to alter the factory-set internal controls or tochange other control settings not specially discussed
in this manual can lead to permanent damage to the Projection Unit and cancellation of the warranty.
Servicing
Do not attempt to service the installed modules yourself, asopening or removing covers may expose you to dangerous voltage
potential and risk of electric shock! Refer all projector service to a qualified BARCO service center.
Call for service in the following conditions :
• When the power cord or plug is damaged or frayed.
• If liquid has been spilled into the modules.
• If the product has been exposed to rain or water.
• If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjustment of the other controls may result in damage and will often
require extensive work by a qualified technician to restore the product to normal operation;
• If the product has been dropped or the cabinet has been damaged;
• If the product exhibits a distinct change in performance, indicating a need for service.
6
R5976468 CINE VERSUM SYSTEM 03112003