Barco Projector Cineversum 120 Quickstart Manual

							7. Connections
Input modeSignal format (1), (2), (3) or (4) selectable on the GUI menu
Bandwidth500 MHz RGB Analog Bandwidth convertor
Signal supportSupports signals up to 205 MHz Pixel clock (1600 x 1200 @ 75 Hz)
Sync DetectionAutomatic Sync detection for: RGBHV, RGBS and RGsB.
Sync PolarityAutomatic Sync Polarity detection
Input signal level
RGsB Input ModeRGB signal: 0.7Vpp
Composite Video Sync on G: 1Vpp
RGBS Input ModeRGB signal: 0.7Vpp
Composite Video Sync on H: 1Vpp
RGB/HV Input ModeRGB signal: 0.7Vpp
Hs Sync signal: 0.7Vpp
Vs Sync signal: 0.7Vpp
Component Input ModeY+Synchro: 1.0Vpp
Pr
Pb
SDI Input
Image 7-23
Features- Loop through SDI Input (SDI in/SDI out)
- For DVD players and other Video equipment with SDI out.
HD SDI Input
Image 7-24
R5976468 CINE VERSUM SYSTEM 0311200357 
						

							7. Connections
Features- Loop through HD-SDI Input (HD-SDI in/HD-SDI out)
- For HD-DVD players and other HD Video equipment with HD-SDI out.
Digital Visual Interface Input (DVI)
DVI: Digital Visual Interface is a display interface developed in repose to the proliferation of digital flat panels
displays. It uses a high speed serial interface with TMDS (Transition Minimized differential signalling) to send
data to the display. DVI can be single or dual link.
Image 7-25
DVI input module
with DVI-D type
connector
Image 7-26
1RX2-7SDA_PC13TMDS DATA 3-19RX0 Shield
2RX2+8nc14+5V Host20TMDS DATA 5-
3RX2 Shield9RX1-15GND21TMDS DATA 5+
4TMDS DATA 4-10RX1+16Hot Plug Detect22TMDS Clock Shield
5TMDS DATA 4+11RX1 Shield17RX0-23RXC+
6SCL_PC12TMDS DATA 3-18RX0+24RXC-
7.4.2 Installation of an Input module
How to install an Input module
1. Has the new input module to be inserted in a free slot?
If yes, go to step 2
If no, go to step 3
2. Take away the dummy plate by removing the two securing screws (A) and continue with step 5. (image 7-27)
3. Unlock the module by loosening the rod screws (A). (image 7-28)
4. Carefully pull out the module (image 7-28).
5. Match the module plug with the slot connector and push the plug into the connector. (image 7-29)
6. Secure the module by tightening the rod screws (A)(image 7-29).
58
R5976468 CINE VERSUM SYSTEM 03112003 
						

							7. Connections
Image 7-27
Image 7-28
Image 7-29
R5976468 CINE VERSUM SYSTEM 0311200359 
						

							7. Connections
60R5976468 CINE VERSUM SYSTEM 03112003 
						

							8. Operating the Remote Control
8. OPERATING THE REMOTE CONTROL
Overview
• Battery Insertion in the Remote Control
• Operating the Remote Control
• Address setting for the Remote Control
8.1 Battery Insertion in the Remote Control
– Insert batteries so that the plus (+) and minus (-) sides are aligned according to the markings in the battery
case.
– Do not mix new batteries with used ones.
– The voltage of batteries may differ even if they are the same shape. Please do not mix different kinds of
batteries.
– When not using the remote control unit for a long period of time (1 month of more), remove the batteries
from the remote control unit to prevent leaking of battery fluid. If battery liquid has leaked, thoroughly wipe
the inside of the case until all liquid is removed, an then insert new batteries.
- Do not charge, short, disassemble or throw the provided batteries in a fire.
When disposing of used batteries, please comply with governmental regulations or environmental public in-
struction’s rules that apply in your country.
Where to find the batteries
The batteries are not placed in the remote control to avoid remote control operation in its package, resulting in a shorter battery life
time.
The batteries are packed separately and added to the package of the remote control.
How to install the batteries
1. Push the cover tab (A) with the fingernail a little backwards and pull upwards the cover top (B). (image 8-1)
2. Slide the cover forwards to remove. (image 8-2)
3. Push the battery body towards the spring and lift it up to remove. (image 8-3)
4. Insert two AA size batteries, making sure the polarities match the + and – marks inside the battery compartment (image 8-3).
5. Insert the lower tab of the battery cover in the gap at the bottom of the remote control, and press the cover until it clicks in place
(image 8-3).
Image 8-1
Battery cover unlock
Image 8-2
Battery cover removal
R5976468 CINE VERSUM SYSTEM 0311200361 
						

							8. Operating the Remote Control
Image 8-3
Battery removal
8.2 Operating the Remote Control
Remote Control operation
This remote control includes a battery powered infrared transmitter which allows the user to control the Cine VERSUM Master re-
motely via its own built-in infrared receiver or via the infrared receivers built-in in the linked displays.
If backlight and RC operation indicator lights up too long or continuously, batteries need to be replaced.
F1F2F3
F4
F5
ADJ EXIT
ENT ER
PA USE
PHAS E TEXT
S HARP N
TI N T
COLOR
BRIGHTN
CONTR
TRE BLE BALANC E
BASS V OL
90
78
56
34
12
45°45°
Cine VERSUM 50Cine VERSUM 80
Cine VERSUM 120
Cine VERSUM Master
Remote Control
Image 8-4
Display Infra Red reception
When operating the remote control unit, point it at the remote sensor, located on the front side of the modules. The remote control
unit is operable up to 9 m from the unit and within a 45 angle on each side of the sensor.
The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal
may differ due to the screen material.
When a key on the remote control is pressed, backlight is activatedautomatically. That allows the user to operate the remote control
in a dark room. Backlight is turned off automatically a few seconds after the last key activation.
62
R5976468 CINE VERSUM SYSTEM 03112003 
						

							8. Operating the Remote Control
Remote control operation’s difficulties
• The remote control unit may not operate if there are objects placed between it and the display.
• Operational distances will gradually become shorter as the batteries begin to wear out, replace weak batteries with new ones
as soon as possible.
• Depending on the installation surroundings, this unit’s remote control may be influenced by the infrared rays discharged from
the plasma display, hampering reception of its rays or limiting its operational distance. The strength of infrared rays discharged
from the screen will differ according to the picture displayed.
8.3 Address setting for the Remote Control
How to set the Remote Control address
1. Point the Remote Control to the module you desire to know the address and press the address key (recessed key).
On-screen and in the graphical display appears the number of the address. Now proceed to program the address in the Remote
Control.
2. Again, press the ADDRESS key on the Remote Control. (image 8-5)
3. Press the digit key, corresponding with the desired address (between 0 and 9), WITHIN 5 SECONDS after the key has been
pressed. (image 8-6)
The commands from the Remote Control are sent with the stored address.
Image 8-5
Address key
Image 8-6
Digit keys
R5976468 CINE VERSUM SYSTEM 0311200363 
						

							8. Operating the Remote Control
64R5976468 CINE VERSUM SYSTEM 03112003 
						

							9. Points of Similarity between Graphical display and On Screen Menus
9. POINTS OF SIMILARITY BETWEEN GRAPHICAL
DISPLAY AND ON SCREEN MENUS
9.1 Explanation about differences in menu displays
Purpose
The different adjustment items are structured in main and sub menus. The way of showing the menus is different between the Cine
VERSUM Master and the linked displays, but the subject matter of the menus is similar. Below a summary of the most important
differences:
Graphical display on Cine VERSUM Master
On the Cine VERSUM Master a 4-line graphical display is built-in, with the result that only 4 items of a menu can be displayed.
Rotating the selection wheel allows to scroll through the items, whereas pressing it, confirms the selection.
CineVERSUM
CineVERSUM
 
>To enter the menu
  Press the button
  or use the RC
  -----------
Graphical Display
on Cine VERSUM Master
CineVERSUM 
7 xga75_gs.c03>To enter the menu
  Press the button
  or use the RC
  -----------
Start up  menu
File of the source included in the display
Started up  menu
Image 9-1
Image 9-2
Indication of the selected item
The selected items on the graphical display are pointed with an arrow whereas the selected ones on the on-screen are highlighted.
R5976468 CINE VERSUM SYSTEM 03112003
65 
						

							9. Points of Similarity between Graphical display and On Screen Menus
CineVERSUM
7 xga75_gs.c03  Image settings
  Advanced Settings
>Installation
  Service
  1 NO MODULE
  2 NO MODULE
  3 VIDEO [VIDEO]
  4 NO MODULE
  5 NO MODULE
  6 NO MODULE
  7 RGB -YUV [RGB]
  8 NO MODULE
  Shutdown
Back
Graphical Display
on Cine VERSUM MasterOn Screen Display
CV50, CV80 and CV120
Main  menuMain  menu
    Cine VERSUM
Image settings
Advanced Settings
Installation
Service
1 NO MODULE
2 NO MODULE
3 VIDEO [VIDEO]
4 NO MODULE
5 NO MODULE
6 NO MODULE
7 RGB -YUV [RGB]
8 NO MODULE
Shutdown
Back
Image 9-3
Scrolling through the on-screen menus (Remote Control)
Scrolling through the on screen menus happens with the up and down cursor keys on the Remote Control. Pressing the ENTER
key confirms of the selection.
Image 9-4
Location of the menu or sub menu title
Title of a menu or sub menu is put on top of the on screen menu and in the left top corner on the graphical display.
66
R5976468 CINE VERSUM SYSTEM 03112003