Home > Barco > Projector > Barco Projector Cineversum 120 Quickstart Manual

Barco Projector Cineversum 120 Quickstart Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Barco Projector Cineversum 120 Quickstart Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 183 Barco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							17. Adjusting the Picture
    17.10Phase adjustment for Computer signals
    About Phase adjustment
    When displaying computer patterns or graphics which are very detailed (tilting, vertical stripes, etc..) jitter in picture (missampling)
    may occur , causing horizontal stripes in portions of the screen.Should this occur, adjust ’Phase’ for optimum computer image.
    How to adjust the Phase
    1. Check if the active source (File) is a RGB or YUV input signal.
    2. Select the ADVANCED SETTINGS menu (menu 17-8).
    3. Select item PHASE by rotating the jog dial on the Master or the up/down arrow keys on the Remote Control. (menu 17-23)
    4. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
    The corresponding bar scale appears on-screen and in the graphical display of the Master. (image 17-10)
    5. Adjust the Phase:
    - With the Remote Control: press the←and→keytorefinethejitter.
    - With the jog dial on the Master: rotate the jog dial to the left or to the right to refine the jitter.
    Note:Don’t mix up with wrong number of total pixels. If the jitterdoesn’t disappear with the phase adjustment, check the total
    number of pixels. (Best image = pixel on pixel off pattern. For example: shut down screen of a PC)
    6. PressEXITon the Remote Control or press the jog dial on the Master to return.
    Advanced Settings
    Aspect Ratio
    Position
    Pip Configuration
    Blanking
    Phase
    Input Balance
    Back
    Menu 17-23
    Image 17-10
    17.11Gamma Correction
    Gamma Correction
    Gamma is an image quality enhancement function that offers a richerimage by brightening the darker portions of the image without
    altering the brightness of the brighter portions.
    Gamma correction as well as Color Temperature set up are available ( = appears in the on-screen menu and
    graphical display) ONLY when the display is remotely addressed with its unique address (Local settings) or
    selected via the Display list.
    R5976468 CINE VERSUM SYSTEM 03112003117 
    						
    							17. Adjusting the Picture
    Only for the Cine VERSUM 80 HD2, three Gamma tables are added to the list, named Film, Graphics and Video.
    How to set up the Gamma value
    1. Enter the MAIN menu and select the sub menu IMAGE SETTINGS, using the jog dial or the Remote Control. (image 17-11)
    Depending the addressed unit:
    - Master: The global Image settings menu isdisplayed, inclusive the menu itemDISPLAY. The latter has to be selected to enter
    the image settings menu for a specific display.
    - Display: The Image settings menu for that specific display appears, inclusive the itemGAMMA.
    2. Select the menu itemGAMMAin the image settings menu for that specific display, by rotating the jog dial on the Master or the
    ↑and↓keys on the Remote Control.
    3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
    A table with the available Gamma values appears on-screen and in the graphical display of the Master. The active Gamma
    correction is indicated with an asterisk in front of the item.
    4. Select the desired Gamma value by rotating the jog dial on the Master or the↑and↓keys on the Remote Control. Changing the
    Gamma value has the following influence on the displayed image:
    Gamma ValueInfluence on the displayed image
    γ=2.2This is the standard value. With reference to the eye perception, the displayed image is the most
    natural image. (Best match between camera recording, projector display and human eye).
    1.0 3.1A higher value occurs a fade away of the details in the dark image content, without changing the
    black level, resulting in a higher contrast perception.
    Film
    Graphics
    VideoGamma tables with lookup tables that can be loaded to enhance Film, Graphics or Video(NTSC,
    PAL, SECAM) display.
    5. PressEXITon the Remote Control or press the jog dial on the Master to return.
    Gamma value is stored for that specific display unit.
    CineVERSUMImage  settings
    Advanced Settings
    Installation
    Service
    1 NO MODULE
    2 NO MODULE
    3 VIDEO [VIDEO]
    4 NO MODULE
    5 NO MODULE
    6 NO MODULE
    7 RGB-YUV [RGB]
    8 NO MODULE
    Shut Down
    BackImage SettingsMaster
      Brightness
      Contrast
      Saturation
      Tint
    Display
    Back
    Display List1 CV50  On
    2 CV80 On
    3 CV120 On
    Back
    Cine VERSUM r01
    If a CV50, CV80 or CV120 is 
    the only display in the linkCV50 - CV80 - CV120
    Main Menu/Image Settings/Display/CV80-CV50-CV120 /Gamma
    Gamma *1.0
      1.3
      1.6
      1.9
      2.2
      2.5
      2.8
      3.1
      Film*
      Graphics*
      Video*
    Back
    * for CV80 only* only CV120
    ** only CV120-CV80
    *** Only CV80
    Image SettingsDisplay
      Brightness
      Contrast
      Gamma
      Color Temperature
      Primaries:[Projector]**
      W hite peak: [OFF]***
      Lamp mode:[Single]*
      Lamp Power:[Normal]*
    Master
    Back
    Image 17-11
    Menu Gamma
    17.12Adjusting theColor Temperature
    Overview
    • Selecting the preset Color Temperature
    • Customizing the Color Temperature
    118
    R5976468 CINE VERSUM SYSTEM 03112003 
    						
    							17. Adjusting the Picture
    About Color Temperature setting
    This function can be used to adjust the color temperature to suit the type of image input to the display unit (DVD, Video, Computer
    image, TV broadcast etc..)
    The Color Temperature menu will include 5 fixed values. To allow the customer to adjust the Color Tempera-
    ture to his own taste, item Customer Balance has been added to the menu.
    Customer Balance adjustment happens differently for Cine VERSUM 50 and the projector displays, Cine VER-
    SUM 80 and Cine VERSUM 120.
    17.12.1 Selecting the preset Color Temperature
    How to select the right Color Temperature
    1. Enter the MAIN menu and select the sub menu IMAGE SETTINGS, using the jog dial or the Remote Control. (image 17-12)
    Depending the addressed unit:
    - Master: The global Image settings menu isdisplayed, inclusive the menu itemDISPLAY. The latter has to be selected to enter
    the image settings menu for a specific display.
    - Display: The Image settings menu for that specific display appears, inclusive the itemCOLOR TEMPERATURE.
    2. Select the menu itemCOLOR TEMPERATUREin the image settings menu for that specific display, by rotating the jog dial on
    the Master or the↑and↓keys on the Remote Control.
    3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
    A table with the preset Color temperature values appears on-screen and in the graphical display of the Master. The active Color
    temperature is indicated with an asterisk in front of the item. (menu 17-24)
    4. Select the Color Temperature item, which suit the type of the input signal, by rotating the jog dial on the Master or the↑and↓
    keys on the Remote Control.
    5. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
    New Color Temperature value is stored and the image changeover to the new Color Temperature.
    6. PressEXITon the Remote Control or press the jog dial on the Master to return.
    Color Temperature value is stored for that specific display unit.
    Color Temperature
    *Display White
    Computer__9300K
    Video_____6500K
    Film______5400K
    Broadcast_3200K
    Custom Balance
    Back
    Menu 17-24
    R5976468 CINE VERSUM SYSTEM 03112003119 
    						
    							17. Adjusting the Picture
    CineVERSUMImage  settings
    Advanced Settings
    Installation
    Service
    1 NO MODULE
    2 NO MODULE
    3 VIDEO [VIDEO]
    4 NO MODULE
    5 NO MODULE
    6 NO MODULE
    7 RGB-YUV [RGB]
    8 NO MODULE
    Shut Down
    BackImage SettingsMaster
      Brightness
      Contrast
      Saturation
      Tint
    Display
    Back
    Display List1 CV50  On
    2 CV80 On
    3 CV120 On
    Back
    Cine VERSUM r01
    If a CV50, CV80 or CV120 is 
    the only display in the link or
    remote addressedCV50 - CV80 - CV120
    Main Menu/Image Settings/Display/CV80-CV50-CV120 /Color Temperature
    * only CV120
    ** only CV120-CV80
    *** Only CV80
    Image SettingsDisplay
      Brightness
      Contrast
      Gamma
      Color Temperature
      Primaries:[Projector]**
      W hite peak: [OFF]***
      Lamp mode:[Single]*
      Lamp Power:[Normal]*
    Master
    Back
    Custom Balance Gain Red
     Gain Green
     Gain Blue
    Back0255 Gain Red 1000255 Gain Green 100
    0255 Gain Blue 100
    Set Color coordinates 
    for white  to adjust 
    Color Temperature
         W hite (X): 0.313
         W hite (Y): 0.329
    BackFront control adjust X
    Push to accept
    Arrow Left/Right adjust X
    Arrow Up/Down adjust Y
     to accept
    W hite (X): 0.313
    W hite (Y): 0.329
    Color Temperature*Display W hite
     Computer 9300K
     Video 6500K
     Film 5400K
     Broadcast 3200K
     Custom Balance
    Back
    CV50  CV80 - CV120
    Image 17-12
    Menu Color Temperature
    Image 17-13
    17.12.2 Customizing the Color Temperature
    How to adjust the Color Temperature for Cine VERSUM 50
    1. Select the Color Temperature item, which match the best the input signal, by rotating the jog dial on the Master or the↑and↓
    keys on the Remote Control (Selecting the preset Color Temperature, page 119).
    2. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
    3. Select item CUSTOM BALANCE by rotating the jog dial on the Master or the↑and↓keys on the Remote Control. (menu 17-25)
    Note:Item ’Display White: an image with maximum white will be displayed.
    4. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
    A sub menu Custom Balance opens, including the Gain adjustments for Red, Green and Blue. The start level of the Gain for the
    three colors corresponds with these of the selected predefined Color Temperature in step 1. (menu 17-26)
    5. Select successively one or more Gain items, depending the ColorTemperature you aim at, by rotating the jog dial on the Master
    or the↑and↓keys on the Remote Control.
    6. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
    The corresponding bar scale appears on-screen and in the graphical display on the Master. (image 17-14)
    120
    R5976468 CINE VERSUM SYSTEM 03112003 
    						
    							17. Adjusting the Picture
    7. Adjust the respective Gain levels, by rotating the jog dial on the Master or the←and→keys on the Remote Control, until the
    desired Color Temperature has been reached.
    8. PressEXITon the Remote Control or select itemBACKin the menus to return.
    Color Temperature
    *Display White
    Computer__9300K
    Video_____6500K
    Film______5400K
    Broadcast_3200K
    Custom Balance
    Back
    Menu 17-25
    Custom Balance
    Gain Red
    Gain Green
    Gain Blue
    Back
    Menu 17-26
    Image 17-14
    How to adjust the Color Temperature for Cine VERSUM 80 and Cine VERSUM 120
    1. Select the Color Temperature item, which match the best the input signal, by rotating the jog dial on the Master or the↑and↓
    keys on the Remote Control (Selecting the preset Color Temperature, page 119).
    2. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
    3. Select item CUSTOM BALANCE by rotating the jog dial on the Master or the↑and↓keys on the Remote Control. (menu 17-27)
    Note:Item ’Display White: an image with maximum white will be displayed.
    4. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
    Note:The measured color coordinates and luminance of R, G, B and W are written into the projector. These were be find by
    measuring with a colorimeter. Adjusting the white coordinatewill not affect the full-on color intensity of a pixel that is R,
    G or B. Via the Custom balance, the preset value of a color temperature can be modified.
    A sub menu opens, requesting to set up the X-Y coordinates for white, inclusive display of the already stored values (image 17-12).
    Overview of the white X-Y coordinates with respectto the preset color temperatures. (image 17-15)
    5. Proceed to the X-Y adjustment, using the jog dial on the master:
    - Select the coordinate to be modified by rotating the jog dial and press to confirm.
    - A new sub menu opens allowing to adjust, by rotating the jog dial, the value of the selected coordinate.
    - Press the jog dial to confirm resulting in return to the coordinated selection menu.
    - Repeat the procedure from the beginning for the other coordinate.
    - Leaving the system, via itemBACK.
    R5976468 CINE VERSUM SYSTEM 03112003
    121 
    						
    							17. Adjusting the Picture
    6. Proceed to the X-Y adjustment, using the Remote Control:
    - Select a coordinate to be modified by pressing the↑or↓key on the Remote Control and pressENTERto confirm.
    - A new sub menu opens allowing to adjust, by pressing the↑or↓keys the Y-value and by pressing←or→keys the X-value.
    -PressEXITto return.
    7. PressEXITon the Remote Control or select itemBACKin the menus to return.
    Color Temperature
    *Display White
    Computer__9300K
    Video_____6500K
    Film______5400K
    Broadcast_3200K
    Custom Balance
    Back
    Menu 17-27
    Display WhiteComputer 9300KVideo 6500K
    Film 5400K
    255
    Broadcast 3200K
    White X: 0.316
    White Y: 0.332White X: 0.283
    White Y: 0.297White X: 0.313
    White Y: 0.329White X: 0.335
    White Y: 0.349White X: 0.423
    White Y: 0.399
    Image 17-15
    17.13Adjusting the Picture Controls
    About picture controls
    Picture controls as, Brightness, Contrast, Saturation and Tintcan be remotely controlled using the Remote control (refer to the
    Owner’s manual). The same functions are also available in the GUI, displayed on-screen and in the graphical display on the Master.
    The three analog controls can be adjusted for all the linked displays at the same time (=Master), on the other hand, corrections can
    be applied for each display separately (=Display), depending the environment conditions.
    Menu overview picture controls
    CineVERSUMImage  settings
    Advanced Settings
    Installation
    Service
    1 NO MODULE
    2 NO MODULE
    3 VIDEO [VIDEO]
    4 NO MODULE
    5 NO MODULE
    6 NO MODULE
    7 RGB-YUV [RGB]
    8 NO MODULE
    Shut Down
    Back
    Main Menu
        Image Settings
    Address Display
    Address Master
    Display List1 Plasma  On
    2 CV80 On
    3 CV120 On
    BackImage SettingsMaster
      Brightness
      Contrast
      Saturation
      
    Display
    Back
    Image SettingsDisplay
      Brightness
      Contrast
      Gamma
      Color Temperature
      
    MasterBack
    Image SettingsDisplay
      Brightness
      Contrast
      Gamma
      Color Temperature
      Primaries:[Projector]
      W hite peak: [OFF]
    MasterBack
    Image SettingsDisplay
      Brightness
      Contrast
      Gamma
      Color Temperature
      Primaries:[Projector]
      Lamp mode:[Single]
      Lamp Power:[Normal]
    MasterBack
    PlasmaCV80
    CV120
    If one Display only
    Cine VERSUM r01Example of a display list
    Image 17-16
    122R5976468 CINE VERSUM SYSTEM 03112003 
    						
    							17. Adjusting the Picture
    17.13.1 Master Adjustment of the Analog Controls
    How to adjust the analog controls
    1. From the main menu, select itemIMAGE SETTINGS.
    Note:When using the Remote Control, make sure that the address of the RC is the common or the Master address!
    The Image Settings menu appears on-screen and in the graphical display on the Master, showing the two main items ’Master’
    and ’Display’. (menu 17-28)
    2. Select the item you want to adjust, using the←or→key on the Remote Control or by rotating the jog dial on the Master.
    3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
    The bar scale, adjustable between 0 and 255, according to the selected analog control appears on-screen and in the graphical
    display. (image 17-17)
    4. Adjust the level of the analog control by rotating the jog dial on the Master or pressing the←or→key on the Remote Control.
    Selected ItemPressing Key←orJogdialtotheleftPressing Key→orJogdialtotheright
    BrightnessFor less brightnessFor more brightness
    ContrastFor less contrastFor more contrast
    SaturationFor less color intensityFor more color intensity
    Tint (NTSC signals only)Skin tones become purplishSkin tones becomes greenish
    5. If you want to proceed to adjustment of the analog controls per display, select itemDISPLAY.Thisitemisexplainedinchapter
    below ’Analog Controls adjustment per Display’.
    6. PressEXITon the Remote Control or press the jog dial on the Master to return.
    New Value of the adjusted analog control is stored in the Cine VERSUM Master and will be applied to all linked displays.
    Image Settings
    Master
    Brightness
    Contrast
    Saturation
    Tint
    Display
    Back
    Menu 17-28
    Image 17-17
    Analog controls
    17.13.2 Analog Controls adjustment per Display
    The items in the display settings per display are, Brightness, Contrast, Gamma and Color Temperature. The 2
    last mentioned items are already explained, see Gamma Correction, page 117, and see Adjusting the Color
    Temperature, page 118.
    R5976468 CINE VERSUM SYSTEM 03112003123 
    						
    							17. Adjusting the Picture
    17.13.2.1Via Cine VERSUM Master
    Chapter below is a continuation of procedure, see Master Adjustment of the Analog Controls, page 123.
    About Image Settings menu
    When adjusting the analog controls separately on the linked display, then the items in the Image Settings menu depends on the
    addressed display. Below the Image Settings menu for respectively the Cine VERSUM 50, the Cine VERSUM 80 and the Cine
    VERSUM 120.
    Image Settings
    Display
    Brightness
    Contrast
    Gamma
    Color Temperature
    Master
    Back
    Menu 17-29
    Image Settings
    Display
    Brightness
    Contrast
    Gamma
    Color Temperature
    Primary [Projector]
    White peak [OFF]
    Master
    Back
    Menu 17-30
    Image Settings
    Display
    Brightness
    Contrast
    Gamma
    Color Temperature
    Primary [Projector]
    Lamp mode [Single]
    Lamp power [Normal]
    Master
    Back
    Menu 17-31
    How to adjust the analog controls per display
    1. From the master IMAGE SETTINGS menu, select itemDISPLAY. (menu 17-32)
    The display list appears on-screen and in the graphical display, showing all the detected displays in the link. (menu 17-33)
    2. Select the Display you want to adjust the analog controls, using the←or→key on the Remote Control or by rotating the jog dial
    on the Master.
    3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
    The Image Settings menu for that specific display (menu 17-29,menu 17-30, menu 17-31) appears on-screen and in the graphical
    display on the Master, including the two main items ’Display’ and ’Master’. These latter two items allow to switch between master
    and display analog control adjustment
    4. Select the item you want to adjust, using the←or→key on the Remote Control or by rotating the jog dial on the Master.
    5. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
    The bar scale, adjustable between -127 and 127, according to the selected analog control appears on-screen and in the graphical
    display. (image 17-18)
    124
    R5976468 CINE VERSUM SYSTEM 03112003 
    						
    							17. Adjusting the Picture
    6. Adjust the level of the analog control, with default value the Master setting, by rotating the jog dial on the Master or pressing the
    ←or→key on the Remote Control.
    Selected ItemPressing Key←or jog dial to the leftPressing Key→or jog dial to the right
    BrightnessFor less brightnessFor more brightness
    ContrastFor less contrastFor more contrast
    7. If you want to proceed to re-adjustment of one of the analog controls for all displays, select itemMasterin the respective Image
    Settings menu (menu 17-29, menu 17-30, menu 17-31).
    The GUI menu returns to the Image settings menu of the Master, and the procedure can be repeated (see Master Adjustment
    of the Analog Controls, page 123)
    8. PressEXITon the Remote Control or press the jog dial on the Master to return.
    New Value of the adjusted analog control is stored in the addressed Display.
    Image Settings
    Master
    Brightness
    Contrast
    Saturation
    Tint
    Display
    Back
    Menu 17-32
    Display List
    2CV50 1:On
    3 CV50 2: Off (Stdby)
    4CV80 1:On
    5 CV120 1: Off (Stdby)
    6CV80 2:On
    Back
    Menu 17-33
    Image 17-18
    Analog controls per display
    17.13.2.2Via Display with Remote Control only
    How to adjust analog controls per display
    1. Program the Remote Control with the address of the Display you want to apply correction to the Brightness and Contrast setting.
    (see Address setting for the Remote Control, page 63).
    2. From the main menu, select itemIMAGE SETTINGS.
    The Image Settings menu for that specific display (menu 17-29,menu 17-30, menu 17-31) appears on-screen and in the graphical
    display on the Master, showing the two main items ’Master’and’Display’.
    3. Select the item you want to adjust, using the←or→key on the Remote Control and press keyENTERon the remote control to
    confirm.
    The bar scale, adjustable between -127 and 127, according to the selected analog control appears on-screen and in the graphical
    display.
    R5976468 CINE VERSUM SYSTEM 03112003
    125 
    						
    							17. Adjusting the Picture
    4. Adjust the level of the analog control, with default value the Master setting, by pressing the←or→key on the Remote Control.
    Selected ItemPressing Key←Pressing Key→
    BrightnessFor less brightnessFor more brightness
    ContrastFor less contrastFor more contrast
    5. If you want to proceed to re-adjustment one of the analog controls for all displays, select item’Master’ (menu 17-29, menu 17-30,
    menu 17-31).
    6. The GUI menu returns to the Image settings menu of the Master, and the procedure can be repeated. (see Master Adjustment
    of the Analog Controls, page 123)
    7. PressEXITon the Remote Control to return.
    New Value of the adjusted analog control is stored in the selected Display.
    126
    R5976468 CINE VERSUM SYSTEM 03112003 
    						
    All Barco manuals Comments (0)

    Related Manuals for Barco Projector Cineversum 120 Quickstart Manual