Barco Projector Cineversum 120 Quickstart Manual

							17. Adjusting the Picture
8. Select the Orientation item which suit the projector mounting by rotating the jog dial on the Master or the up/down arrow keys on
the Remote Control.
9. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The projector fits to the selected image orientation and the system returns to operation automatically after a few seconds. (im-
age 17-1)
Installation
Input slots
File service
Display list
Internal pattern
When no signal
Source transition
OSD Configuration
Language
Keystone
Global keystone: Yes
Output: [Largest]
Default input balance
Back
Menu 17-4
Display List
2CV50 1:On
3 CV50 2: Off (Stdby)
4CV80 1:On
5 CV120 1: Off (Stdby)
6CV80 2:On
Back
Menu 17-5
Display settings
Switch OFF
Display Info
Rename
Update Software
IR address: 9
CW Index
Orientation
Projector_mode
Back
Menu 17-6
Orientation
Front/Table
Rear/Table
Front/Ceiling
Rear/Ceiling
Back
Menu 17-7
Image 17-1
Image orientation adjustment
17.3 Adjusting the Image Aspect Ratio
How to adjust the image Aspect Ratio
This function allows you to modify or customize the image display mode to enhance the input image.
1. Press the jog dial on the Master or theADJkey on the Remote Control.
The Main menu appears on-screen and in the graphical display. (menu 17-8)
2. Select item ADVANCED SETTINGS by rotating the jog dial on the Master or the up/down arrow keys on the Remote Control
(menu 17-8).
3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The sub menu ADVANCED SETTINGS appears on-screen and in the graphical display. (menu 17-9)
4. Select item ASPECT RATIO by rotating the jog dial on the Master or the up/down arrow keys on the Remote Control.
R5976468 CINE VERSUM SYSTEM 03112003
107 
						

							17. Adjusting the Picture
5. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The sub menu ASPECT RATIO appears on-screen and in the graphicaldisplay, including all available aspect ratios. (menu 17-10)
Explanation
Aspect RatioDescription
FitForces format of all input signals into the native panel resolution.
16:9Wide screen television format/Anamorf format.
4:3Standard television format.
5:4Workstations format.
2.35Panavision or Cinemascope format, frequently used by Hollywood films.
1.88Film format used by a lot of non-action films.
1.78Wide screen television format/Anamorf format.
LetterboxForces the letter format of the input signal into the native panel resolution.
6. Select the desired ASPECT RATIO (depending the image format of the input source) item by rotating the jog dial on the Master
or the up/down arrow keys on the Remote Control and press respectively the jog dial on the Master of keyENTERon the Remote
Control to confirm. (image 17-2)
7. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
Image of the input signal is displayed in the selected format. If item FIT is selected, then the image format of the selected input
source is forced into the native panel resolution, with or without loss of image contents.
Cine VERSUM System
Image Settings
Advanced Settings
Installation
Service
1 NO MODULE
2 NO MODULE
3 VIDEO [VIDEO]
4 NO MODULE
5 NO MODULE
6 NO MODULE
7 RGB-YUV [RGB]
8 NO MODULE
Shutdown
Back
Menu 17-8
Advanced Settings
Aspect Ratio
Position
Pip Configuration
Blanking
Phase
Input Balance
Back
Menu 17-9
Aspect Ratio
*Fit
16:9
4:3
5:4
2.35
1.88
1.78
Letterbox
Back
Menu 17-10
Image 17-2A Letterbox format input signal
B Conversion to native panel resolution
108
R5976468 CINE VERSUM SYSTEM 03112003 
						

							17. Adjusting the Picture
17.4 Adjusting the Decoding Standard
About Decoding Standard
The possibility is offered to decode the NTSC video signals via the default American IRE standard (Decoding a NTSC signal using
the European EBU standard may result in a greenish tint.) and the PAL/SECAM video signals via the European EBU standard.
When the PROJECTOR standard has been chosen, then, video signal are decoded based on the installed Color Parameters.
Choice of the color decoding standard is applicable on the Cine VERSUM 80 and Cine VERSUM 120 only.
Where to select the color decoding
1. Enter the MAIN menu and scroll through the sub menus, using the jog dial or the Remote Control until the Image Settings menu
is displayed. (image 17-3)
2. Select itemPRIMARIESby rotating the jog dial on the Master or the up/down arrow keys on the Remote Control.
3. Press the jog dial on the Master or theENTERkey on the Remote Control to select the desired standard, indicated between
brackets.
4. To leave the GUI, use the itemBACKin the menus or theEXITkey on the Remote Control.
CineVERSUMImage  settings
Advanced Settings
Installation
Service
1 NO MODULE
2 NO MODULE
3 VIDEO [VIDEO]
4 NO MODULE
5 NO MODULE
6 NO MODULE
7 RGB-YUV [RGB]
8 NO MODULE
Shut Down
BackImage SettingsMaster
  Brightness
  Contrast
  Saturation
  Tint
Display
Back
Display List1 CV50  On
2 CV80 On
3 CV120 On
Back[Projector/EBU/ANSI]
Cine VERSUM r01
If 1 display in the linkCV80
CV120Image SettingsDisplay
  Brightness
  Contrast
  Gamma
  Color Temperature
  Primaries :[Projector]
  Lamp mode:[Single]
  Lamp Power:[Normal]
MasterBack
Main Menu/Image Settings/Display/CV80 or CV120 /Primaries
Image SettingsDisplay
  Brightness
  Contrast
  Gamma
  Color Temperature
  Primaries:[Projector]
  W hite peak: [OFF]
MasterBack
Image 17-3
Color standard selection
17.5 White Peak Set up
About White Peak
In video centric applications true color reproduction is generallya priority over brightness. To achieve this a typical design will not
utilize a white segment. This has the side effect of reducing the amount of light allowed through the color wheel, which reduces the
overall brightness. To compensate for this a technique can applied called Spoke Light Capture (SLR).
The spokes are defined to be the time between colors. The DMD is normally kept in the “off” state during this time preventing any
light from getting to the screen. If the light is passed trough the spokes, the average over time across them is made up of a mixture
of the two adjacent colors. This will results in a secondary color. If these spokes are taken three at a time, over time they will sum
up to white light. This “virtual white segment” is the basic principal of SLR and can yield a substantial boost to system brightness.
Where to set up the white Peak
1. Enter the MAIN menu and scroll through the sub menus, using the jog dial or the Remote Control until the Image Settings menu
is displayed. (image 17-4)
2. Select itemWHITE PEAKby rotating the jog dial on the Master or the up/down arrow keys on the Remote Control.
3. Press the jog dial on the Master or theENTERkey on the Remote Control to enable (On) or disable (Off) the white peak feature,
status indicated between brackets.
4. To leave the GUI, use the itemBACKin the menus or theEXITkey on the Remote Control.
R5976468 CINE VERSUM SYSTEM 03112003
109 
						

							17. Adjusting the Picture
CineVERSUMImage  settings
Advanced Settings
Installation
Service
1 NO MODULE
2 NO MODULE
3 VIDEO [VIDEO]
4 NO MODULE
5 NO MODULE
6 NO MODULE
7 RGB-YUV [RGB]
8 NO MODULE
Shut Down
BackImage SettingsMaster
  Brightness
  Contrast
  Saturation
  Tint
Display
Back
Display List1 CV50  On
2 CV80 On
3 CV120 On
Back[On/Off]
Cine VERSUM r01
If the CV80 is the only display in the linkCV80
Main Menu/Image Settings/Display/CV80 or CV120 /Primaries
Image SettingsDisplay
  Brightness
  Contrast
  Gamma
  Color Temperature
  Primaries:[Projector]
  W hite peak: [OFF]
MasterBack
Image 17-4
White peak set up
17.6 Keystone Correction
Keystone correction set up is applicable on the Cine VERSUM 80 and on the Cine VERSUM 120 only.
Overview
• Setting the Keystone correction: Global or on a File
• Applying the Keystone correction
About Keystone correction
In case of an inclined projector mounting, side keystone correction has to be applied to the displayed picture.
Straight lines and the edges of the displayed image may appears jagged, when adjusting the Keystone setting.
The Installation menu includes the items KEYSTONE and GLOBAL KEYSTONE Yes/No. The latter allows to define if keystone
correction may be applied to ALL files (Yes) or only to the active file (No).
Matching to the file on the respective input slots 1 to 8, an additional file is created on the corresponding input
slot numbers, 91 to 98. Both matching files can contain different settings.
17.6.1 Setting the Keystone correction: Global or on a File
How to set the Keystone correction
1. Press the jog dial on the Master or theADJkey on the Remote Control.
The Main menu appears on-screen and in the graphical display. (menu 17-11)
2. Select item INSTALLATION by rotating the jogdial on the Master or the up/down arrow keys on the Remote Control (menu 17-11)
and press to confirm.
3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The sub menu INSTALLATION appears on-screenand in the graphical display. (menu 17-12)
110
R5976468 CINE VERSUM SYSTEM 03112003 
						

							17. Adjusting the Picture
4. Select item GLOBAL KEYSTONE: YES by rotating the jog dial on the Master or the up/down arrow keys on the Remote Control
(menu 17-12).
5. Set Global Keystone to Yes or to No, using the jog dial on the Master or the keyENTERon the Remote Control as toggle switch.
- Confirmation YES: Keystone correction will be applied to ALL files.
- Confirmation NO: keystone correction will be applied to the ACTIVE file.
Cine VERSUM System
Image Settings
Advanced Settings
Installation
Service
1 NO MODULE
2 NO MODULE
3 VIDEO [VIDEO]
4 NO MODULE
5 NO MODULE
6 NO MODULE
7 RGB-YUV [RGB]
8 NO MODULE
Shutdown
Back
Menu 17-11
Installation
Input slots
File service
Display list
Internal pattern
When no signal
Source transition
OSD Configuration
Language
Keystone
Global keystone: Yes
Output: [Largest]
Default input balance
Back
Menu 17-12
17.6.2 Applying the Keystone correction
How to adjust Keystone correction
1. Select item KEYSTONE by rotating the jog dial on the Master or the up/down arrow keys on the Remote Control. (menu 17-13)
2. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
A bar scale with zero point appears on-screen and in the graphical display of the Master. (image 17-5)
3. Adjust the Keystone
- With the Remote Control: press the←and→key to adjust the Keystone correction.
- With the jog dial on the Master: rotate the jog dial to the left or to the right to adjust the Keystone correction.
4. PressEXITon the Remote Control or press the jog dial on the Master to return.
Installation
Input slots
File service
Display list
Internal pattern
When no signal
Source transition
OSD Configuration
Language
Keystone
Global keystone: Yes
Output: [Largest]
Default input balance
Back
Menu 17-13
Image 17-5
Keystone correction
R5976468 CINE VERSUM SYSTEM 03112003111 
						

							17. Adjusting the Picture
17.7 Adjusting the Image Shift and Size
Overview
• Adjusting the Image Shift
• Adjusting the Image Size
17.7.1 Adjusting the Image Shift
How to adjust the Vertical and Horizontal image shift
1. Select the ADVANCED SETTINGS menu (menu 17-8).
2. Select item POSITION by rotating the jog dial on the Master or the up/down arrow keys on the Remote Control. (menu 17-14)
3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The sub menu POSITION appears on-screen and in the graphical display. This menu contains the items Vertical and Horizontal
shift and size. (menu 17-15)
4. Select the SHIFT item, horizontal or vertical, you desire to adjust by rotating the jog dial on the Master or the up/down arrow keys
on the Remote Control.
5. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
A bar scale with zero point appears on-screen and in the graphical display of the Master. (image 17-6)
6. Adjust the shift:
- With the Remote Control: press the←or→key to adjust the shift level.
- With the jog dial on the Master: rotate the jog dial to the left or to the right.
7. PressEXITon the Remote Control or press the jog dial on the Master to return.
Advanced Settings
Aspect Ratio
Position
Pip Configuration
Blanking
Phase
Input Balance
Back
Menu 17-14
Position
Horizontal Shift
Horizontal Size
Vertical Shift
Horizontal Size
Back
Menu 17-15
Image 17-6
Picture shift adjustment
112R5976468 CINE VERSUM SYSTEM 03112003 
						

							17. Adjusting the Picture
17.7.2 Adjusting the Image Size
How to adjust the Vertical and Horizontal image size
1. Select sub menu POSITION (Adjusting the Image Shift, page 112)
2. Select the SIZE item, vertical or horizontal, you desire to adjust by rotating the selection wheel on the Master or the up/down
arrow keys on the Remote Control. (menu 17-16)
3. Press the selection wheel on the Master or the key ENTER on the Remote Control to confirm.
A barscale with zero point appears on-screen and in the graphical display of the Master. (image 17-7)
4. Adjust the size:
- With the Remote Control: press the←or→key to adjust the shift level.
- With the selection wheel on the Master: rotate the wheel to the left or to the right.
5. PressEXITon the Remote Control or press the selection wheel on the Master to return.
Position
Horizontal Shift
Horizontal Size
Vertical Shift
Horizontal Size
Back
Menu 17-16
Image 17-7
Picture size adjustment
17.8 Outline the displayed Image (Blanking)
How to outline the displayed image
Undesired information at the borders of the displayed image can be removed with the blanking adjustment. Follow next steps:
1. Select the ADVANCED SETTINGS menu (menu 17-8).
2. Select item BLANKING by rotating the jog dial on the Master or the up/down arrow keys on the Remote Control.
3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The sub menu BLANKING appears on-screen and in the graphical display. This menu contains the items Top/Bottom and
Left/Right blanking. (menu 17-17)
4. Select the side of the image you desire to apply blanking by rotating the jog dial on the Master or the up/down arrow keys on the
Remote Control.
5. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The corresponding bar scale appears on-screen and in the graphical display of the Master. (image 17-8)
R5976468 CINE VERSUM SYSTEM 03112003
113 
						

							17. Adjusting the Picture
6. Adjust the blanking:
- With the Remote Control: press the←or→key to adjust the blanking level.
- With the jog dial on the Master: rotate the jog dial to the left or to the right.
7. PressEXITon the Remote Control or press the jog dial on the Master to return.
Blanking
Top
Bottom
Left
Right
Back
Menu 17-17
Image 17-8
Blanking adjustment
17.9 Alignment of the Input Balance
Overview
• Input Balance Selection
• Input Balance Adjustment
About the Input Balance alignment
Two kind of input balance alignments, ONLY APPLICABLE on RGB/YUV input signals, can be find in the menu structure, one named
’Default Input Balance’ (classified in the Installation menu) and the other named ’Input Balance’ (classified in the Advanced settings
menu).
Installation
Input slots
File service
Display list
Internal pattern
When no signal
Source transition
OSD Configuration
Language
Keystone
Global keystone: Yes
Output: [Largest]
Default input balance
Back
Menu 17-18
114R5976468 CINE VERSUM SYSTEM 03112003 
						

							17. Adjusting the Picture
Advanced Settings
Aspect Ratio
Position
Pip Configuration
Blanking
Phase
Input Balance
Back
Menu 17-19
The ’Default Input Balance’ is used to align the input balance of the different modules referring to standard input signals.
As standard input signals are required for the alignment of the Default Input Balance, this alignment has to
be consider as FACTORY ALIGNED. Attempting to align the Default Input Balance can have serious conse-
quences on the image performances. For that reason, the Default Input Balance adjustment has been made
inaccessible.
Due to the signal distribution or the signal transmissions, a color imbalance can occurs. To allow the customer to be able to correct
the imbalance per file, the alignment ’Input Balance’, situated in the menu Advanced Settings, has been provided.
Observe the image on color dominance in the black and white areasof the displayed picture. If color dominance has been observed
in one of the areas or in both, then proceed tothe corresponding input balance adjustment.
Adjust the Color Saturation level to zero before starting the Input Balance adjustment.
17.9.1 Input Balance Selection
How to select the Input Balance
1. Check if the active source (File) is a RGB or YUV input signal.
2. Select the ADVANCED SETTINGS menu (menu 17-8).
3. Select item INPUT BALANCE by rotating the jog dial on the Master or the up/down arrow keys on the Remote Control
(menu 17-19).
4. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The sub menu INPUT BALANCE appears on-screen and in the graphical display. This menu contains the items White and Black
balance, as well as the return to the Factory settings. (menu 17-20)
Input Balance
White Balance
Black Balance
Factory Settings
Back
Menu 17-20
After changing the Input Balance, a return to the factory settings can be obtained by selecting the item FAC-
TORY SETTINGS in the Input balance menu, followed by a confirmation.
R5976468 CINE VERSUM SYSTEM 03112003115 
						

							17. Adjusting the Picture
17.9.2 Input Balance Adjustment
How to adjust the Input Balance
Always start with the Black balance adjustment ifa dominant color has been observed in both areas.
1. Select in the Input Balance menu item BLACK BALANCE and confirm.
A sub menu appears on-screen and in the graphical display, showing the adjustable items Black Level RED and BLUE.
(menu 17-21)
2. Select, depending the color dominant, in the Black Balancemenu item BLACK LEVEL RED or Blue and confirm. If necessary
apply the adjustment for both colors.
The corresponding bar scale appears on-screen and in the graphical display of the Master. (image 17-9)
3. Adjust the Black level:
- With the Remote Control: press the←and→key to increase or decrease the color level.
- With the jog dial on the Master: rotate the jog dial to the left or to the right to increase or decrease the color level.
4. PressEXITon the Remote Control or press the jog dial on the Master to return.
5. Select in the Input Balance menu item WHITE BALANCE and confirm.
A sub menu appears on-screen and in the graphical display, showing the adjustable items Gain RED and BLUE. (menu 17-22)
6. Select, depending the color dominant, in the White Balance menu item GAIN RED or Blue and confirm. If necessary apply the
adjustment for both colors.
The corresponding bar scale appears on-screen and in the graphical display of the Master (image 17-9).
7. Adjust the Gain level:
- With the Remote Control: press the←and→key to increase or decrease the color gain.
- With the jog dial on the Master: rotate the jog dial to the left or to the right to increase or decrease the color gain.
8. PressEXITon the Remote Control or press the jog dial on the Master to return.
Black Balance
Black level Red
Black level Blue
Back
Menu 17-21
White Balance
Gain Red
Gain Blue
Back
Menu 17-22
Image 17-9
Input balance adjustment
116R5976468 CINE VERSUM SYSTEM 03112003