Barco Projector Cineversum 120 Quickstart Manual

							6. Installation Guidelines
PDA
B
C
PD
16 9SW
Image 6-5
Calculation of the projector distance (PD)
Below table of the lenses (available at time of printing)
LensesMetric formulas (meter)Inch formulas (inch)
CineVERSUM™(1.2 - 1.44 : 1)WidePD = 1.2 x SWPD = 1.2 x SW
Te l ePD = 1.44 x SWPD = 1.44 x SW
CineVERSUM™(1.44 - 1.8 : 1)WidePD = 1.44 x SWPD = 1.44 x SW
Te l ePD = 1.88 x SWPD = 1.88 x SW
CineVERSUM™(1.6 - 2.24 : 1)WidePD = 1.6 x SWPD = 1.6 x SW
Te l ePD = 2.24 x SWPD = 2.24 x SW
CineVERSUM™(2.24 - 4 : 1)WidePD = 2.24 x SWPD = 2.24 x SW
Te l ePD = 4 x SWPD = 4 x SW
CineVERSUM™(3.6 - 5.6 : 1)WidePD = 3.6 x SWPD = 3.6 x SW
Te l ePD = 5.6 x SWPD = 5.6 x SW
CineVERSUM™(4 - 6.4 : 1)WidePD = 4 x SWPD = 4 x SW
Te l ePD = 6.4 x SWPD = 6.4 x SW
R5976468 CINE VERSUM SYSTEM 0311200337 
						

							6. Installation Guidelines
6.1.2.4 Projector installation requirements
Cine VERSUM 80: Installation requirements
• Position the projector perpendicular to the screen and leveled to achieve an optimal image. An inclination of the projector is
allowed but limited to 10° in one direction (. The latter generates image distortion (keystoned) which can be corrected using
the projector’s menu system.
• The projector lens should be centered horizontally in themiddle of the screen (Vertical shift of the lens built-in).
• Position the screen so that it is not in direct sunlight or room light. Light falling directly onto the screen washes out the colors,
making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.
• A polarizing screen cannot be used with this projector.
The maximum mounting inclination angle for the projector is 10°.
Image 6-6
Projector inclination angle
1 Ceiling mounted projector
2 Table installed projector
Cine VERSUM 120: Installation requirements
• Position the projector perpendicular to the screen and leveled to achieve an optimal image. An inclination of the projector is
allowed but limited due to the maximum keystone correction range.
• A swing of the projector is limited to 10° in both directions (due to the lamp position in the projector).
• The projector lens should be centered horizontally in the middle of the screen (Vertical and Horizontal shift of the lens built-in).
• Position the screen so that it is not in direct sunlight or room light. Light falling directly onto the screen washes out the colors,
making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.
• A polarizing screen cannot be used with this projector.
The maximum mounting swing angle for the projector is 10°.
10 °10 °
10 °
10 °1
2
Image 6-7
Projector swing angle
1 Table installed projector
2 Ceiling mounted projector
6.1.2.5 Lens Control
Cine VERSUM 80: Using the provided Lens vertical Shift control
The picture can be adjusted vertically within the shift range of the lens by rotation the lens shift screw on top of the projector (below
top cover) using a flat screwdriver or byhand to match the setup configuration.
The vertical lens shift range is +100% and –100% with respect to the optical axis of the projection lens (Tilting the projector will
reduce the effectiveness of the lens shift function).
38
R5976468 CINE VERSUM SYSTEM 03112003 
						

							6. Installation Guidelines
When the height of the projected image is adjusted, the image maybecome distorted (keystoned),depending on the relative posi-
tions of the projector and the screen. How to adjust the keystone correction, see Keystone Correction, page 110.
Optical Axis Projector Lens
16
9
Optical Axis Projector Lens
16
9
1
2
Image 6-8
Lens shift
1 Lens shift fixed screen
2 Lens shift fixed projector
Cine VERSUM 120: using the provided Lens Controls
The Cine VERSUM 120 is equipped with a zoom lens which is remote controlled. The following controls are provided:
• Lens FOCUS alignment
• Lens ZOOM alignment
• Lens HORIZONTAL SHIFT alignment
• Lens VERTICAL SHIFT alignment
Picture below shows a running through the menus to access to the lens controls (For details, see owners manual of the Cine VER-
SUM 120):
InstallationInput Slots
File Service
Display List
Internal Pattern
W hen no signal
Source Transition
OSD configuration
Language
Keystone
Global Keystone:Yes
Output: [Largest]
Default Input Balance
Back
Access to Lens controls
Lens  Focus
  Hor. Shift
  Vert. shift
  Zoom
BackLens  Use arrow keys
      to control
        the lens
Back
Display Settings Switch OFF
 Display Info
 Rename
 IR Address 009
 Diagnosis
 Orientation
 Test patterns
 Lens
 Lamp
BackDisplay List1 CV50        On
2 CV80        On
3 CV120      On
Back
Main Menu/Installation/Display list/CV120/Lens
Image 6-9
Access to lens controls
R5976468 CINE VERSUM SYSTEM 0311200339 
						

							6. Installation Guidelines
6.1.2.6 Ceiling Mount for Cine VERSUM 80 Cine VERSUM 120
View Ceiling Mount assembly
R9841750
Image 6-10
Ceiling mount for Cine VERSUM 80
For more details about the ceiling mount Cine VERSUM 80, see the concerning installation manual.
R9842330
Image 6-11
Ceiling mount for Cine VERSUM 120
For more details about the ceiling mount Cine VERSUM 120, see the concerning installation manual.
Ceiling Mount Extension Supports for Cine VERSUM 80 and Cine VERSUM 120
Two extension supports are available and are common for both projectors.
Image 6-12
Extension supports for ceiling mount assembly
For more details about the ceiling mount extension support, see the concerning installation manual.
40
R5976468 CINE VERSUM SYSTEM 03112003 
						

							6. Installation Guidelines
6.2 Plasma Screen Installation Guidelines
Overview
• About Installation of the Unit
• Installation using the Wall mount kit
• Installation using the Table mount kit
6.2.1 About Installation of the Unit
To avoid malfunction, overheating of this unit, and possible fire hazard, make sure that the vents on the main
unit are not blocked when installing. Also hot air is expelled from the air vents, be careful of deterioration and
dirt build up on rear surface wall, etc..
Please be sure to use an M8 (Pitch=1.25mm) bolt. (Only this size bolt can be used.)
Because this unit weights about 40 kg and the lack of depth makes it fairly unstable, please use 2 people or
more when packing, carrying or installing.
This unit incorporates a thin design. To ensure safety if vibrated or shaken, please be sure to take measures
to prevent the unit from tipping over.
Way of installing the unit
Two kits are designed by BARCO for the installation of the unit, a Wall and a Table mount kit.
6.2.2 Installation using the Wall mount kit
How to install the Wall mount kit
1. Be sure to attach in 4 or more locations above and below, left and right of the center line.
2. Use bolts that are long enough to be inserted 12 mm to 18 mm into the main unit from the attaching surfaces for both ’a’ holes
and ’b’ holes. Refer to the side view diagram below.
3. As this unit is constructed with glass, be sure to install it on a flat, not warped surface. (image 6-13, image 6-14, image 6-15)
Image 6-13
Mounting holes
R5976468 CINE VERSUM SYSTEM 0311200341 
						

							6. Installation Guidelines
This side has to be fixed to the plasma backplane
M8x20 (for fixing support plate to plasma backplane)
Image 6-14
Wall mount assembly
Image 6-15
Dimensions wall mount assembly
6.2.3 Installation using the Table mount kit
How to install the Table mount kit
1. Assemble the table mount as illustrated in drawing below. (image 6-16)
2. Mount the table mount onto the rear of the Cine VERSUM 50, using the ’a’ holes (Installation using the Wall mount kit, page 41).
42
R5976468 CINE VERSUM SYSTEM 03112003 
						

							6. Installation Guidelines
Image 6-16
Table mount assembly
R5976468 CINE VERSUM SYSTEM 0311200343 
						

							6. Installation Guidelines
44R5976468 CINE VERSUM SYSTEM 03112003 
						

							7. Connections
7. CONNECTIONS
Overview
• Power Supply Connection
• Connection for Preview and Communication
• Digital Link to Display Modules
• Connection to Video Equipment
7.1 Power Supply Connection
7.1.1 Supplied Power Cords
The following power cords are added to the product
In the package of each product, two power cords are added, one with a plug shape, reference standard ANSI C73.11, and one with
a plug shape, reference CEE (7).
Image 7-1
Power cord ANSI for Cine VERSUM 50, Cine VERSUM 80 andCineVERSUM
MasterImage 7-2
Power cord CEE for Cine VERSUM 50, Cine VERSUM 80 andCine VERSUM
Master
Image 7-3
Power cord ANSI (L-shaped socket) for Cine VERSUM 120Image 7-4
Power cord CEE (L-shaped socket) for Cine VERSUM 120
7.1.2 Power Connection Cine VERSUM Master
AC Power Cord connection
Use the supplied power cord to connect the Cine VERSUM Master to the wall outlet. Plug the female power connector into the male
connector at the rear of the unit. Make sure that the power cord is firmly inserted into the AC socket.
R5976468 CINE VERSUM SYSTEM 03112003
45 
						

							7. Connections
Image 7-5
Insertion of the power plug
AC Power Specifications
AC Power VoltageAuto Range 100 – 240V
AC Power Current1A/50–60Hz
Main FusesStandby Power Supply: T 2AH/250V
Main Power Supply: F 4A L 250V
Power Consumption
Normal operation mode78 W
Depending on input configuration
Standby mode8W
Economic standby mode4W
For continued protection against risk of fire, all fuse replacements must be made using VDE and UL Listed or
Recognized fuses with the same voltage and current rating.
7.1.3 Power Connection Cine VERSUM 80
AC Power Cord connection
Use the supplied power cord to connect the Cine VERSUM 80 to the wall outlet. First, remove the back cover (turn the quarter turn
fastener a quarter turn counterclockwise) to facilitate the power plug insertion. Then, plug the female power connector into the male
connector at the rear of the unit. Make sure that the power cord is firmly inserted into the AC socket and routed from the bottom side.
Image 7-6
Removal back cover
Image7-7
Insertion of the power plug
46R5976468 CINE VERSUM SYSTEM 03112003