Avaya Partner Advanced Communications System Installation, Programming And Use Manual

Overview
D-1
D
Programming Mixed Telephone Types
Overview
This appendix provides information about programming from a PARTNER-34D telephone to MLS 
telephones and from an MLS-34D telephone to PARTNER telephones. In these situations, be 
aware that the button that you press at extension 10 or 11 (the programming extension) is likely to 
be in a different location than the button on the telephone to which the programming applies (the 
target telephone). If you are programming from a PARTNER-18D or MLS-18D...

PA R T N E R® Advanced Communications System Installation, Programming, and Use
Overview
D-2
Figure D-1. Programming from a PARTNER 34-D Telephone
Intercom Intercom
Ext.
Volume Speakerphone
Spkr
Spkr
Mic
HFAI
PARTNER-34D Overlay
Intercom Intercom Ext.
Volume Intercom Intercom
Ext.
MLS-6 Phone
MLS-18D/12D/12 Phone
MLS-34D Phone
Message 

Programming Mixed Telephone Types
Overview
D-3
Figure D-2. Programming from an MLS-34D Telephone
PARTNER-6 Phone
PARTNER-18D/18 Phone
Intercom IntercomExt.Message
Intercom Intercom
Message Ext.
PARTNER-34D Phone
Intercom IntercomExt.Message
MLS-34D Overlay 

PA R T N E R® Advanced Communications System Installation, Programming, and Use
Overview
D-4 

E-1
E
Flow Charts
System Programming Flow Chart–How to Use
To use the following sets of Flow Charts, follow these instructions first:
Place the Programming Overlay on the dial pad of the system display phone at extension 10 or 11.

To Start System Programming: 
– Press 
f00 
– Press 
s s 

To End System Programming: 
– Press 
f00 

To Use a Specific Procedure: 
– Dial 
# and a three-digit procedure code.
(Example: 
#101 for System Date) 

To Cycle through System Programming Procedures: 
– Press 
N or P...

Flow Charts
E-2
System Flow Chart–System
Outgoing Call Restriction
Button
Dial 
#114
Dial 1=Assigned
2=Not Assigned ✔ 
3=Select Button then press a 
programmable button 
System Date
Dial 
#101
Dial the date (MMDDYY) 
Number of Lines
Dial 
#104
Dial two digits (01-31) (R 4.0), or 
Dial two digits (01-19) (Prior to R 4.0),
for # of outside lines assigned to every 
extension. 3 per ACS processor & 
308EC module. 2 per 206 or 200 module 
✔. 4 per 400 module ✔ 
WARNING 
Do not use Number of Lines (#104) after...

Flow Charts
E-3
System Flow Chart–System Speed Dial numbers
System Flow Chart–Lines
To program a number: 
Press 
f00 to enter programming mode 
Press 
f
Dial a three-digit code (600-699) 
Dial the telephone number–up to 28 digits including special characters. 
To “mark” it (to override restrictions), dial * before the telephone # 
To program another number, or to change a number, repeat: 
Press 
NP, enter a new extension # and 
repeat above steps 
Press 
f00 to exit programming mode To remove a number:...

PA R T N E R® Advanced Communications System Installation, Programming, and Use
E-4
System Flow Chart–Extensions
Line Assignment
Dial 
#301
Dial a system extension # 
To remove all existing line assignments, 
press 
r before selecting a line.
Dial a line number
Dial 1=Assigned ✔
2=Not Assigned 
3=Select Button then press a programable 
button (to assign the line to that button). If 
you use option 3 after a line has been 
assigned, the line moves from the old 
button to the new button you select.
Press...

Flow Charts
E-5
System Flow Chart–Extensions (Continued)
Call Waiting
Dial 
#316
Dial a system extension #
Dial 1=Assigned
2=Not Assigned ✔ 
Press 
n to program another extension
Caller ID Log Answered Calls
Dial 
#317
Dial a system extension #
Dial 1=Active
2=Not Active ✔ 
Press 
n to program another extension
Caller ID Log Line Association
Dial 
#318
Dial a system extension #
Dial a system line #
Press 
n to program another extension
To associate another extension: 
Press
 N P, enter a 
new extension #...

PA R T N E R® Advanced Communications System Installation, Programming, and Use
E-6
System Flow Chart–Dialing Restrictions and Permissions
Outgoing Call Restriction
Dial 
#401
Dial a system extension #
Dial 1=No Restriction ✔
2=Inside Only (intercom)
3=Local Only (intercom and local) 
Press 
n to program another extension
Toll Call Prefix
Dial 
#402
Dial 1=0/1 plus Area Code and # ✔
2=Area Code and # only
System Password 
Dial 
#403
Dial four digits to set the password
Disallowed List Assignments
Dial...