Home > ATT > Communications System > ATT DEFINITY Communications System Generic 3 For Single-Carrier Cabinets Instructions Manual

ATT DEFINITY Communications System Generic 3 For Single-Carrier Cabinets Instructions Manual

    Download as PDF Print this page Share this page

    Have a look at the manual ATT DEFINITY Communications System Generic 3 For Single-Carrier Cabinets Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 164 ATT manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Power U p Switch
    September 1995 Issue 1 
    7-3
    Power up AC-Powered Switch
    1. Ensure the associated circuit breakers on the AC power panel are ON.
    NOTE:
    If the system is configured for High or Critical Reliability, power-up 
    the Expansion Port Network (EPN) cabinet first, then the Processor 
    Port Network (PPN) cabinet. 
     Always power up the Control Cabinet 
    last
     in any multi-cabinet configuration.
    2. At the rear of each cabinet, set the circuit breaker to ON. Go to ‘‘Verify 
    Messages.’’
    NOTE:
    This action starts the system initialization and test. All red lights on 
    the circuit packs go on and then off. 
    Power up DC-Powered Switch
    1. At the DC Battery Cabinet, set  circuit breaker to ON.
    NOTE:
    If the system is configured for High or Critical Reliability, power-up 
    the Expansion Port Network (EPN) cabinet first, then the Processor 
    Port Network (PPN) cabinet. 
     Always power up the Control Cabinet 
    last
     in any multi-cabinet configuration.
    2. At DC Power Cabinet, set the circuit breaker(s) on the associated rectifiers 
    ON.
    3. At the rear of each Power Distribution Unit, set the circuit breaker to ON.
    NOTE:
    This action starts the system initialization and test. All red lights on 
    the circuit packs go on and then off. Some red lights may come back 
    on in a few seconds or a few minutes and will b e turned off by other 
    procedures in this chapter.
    Verify Messages on Terminal
    1. After several minutes, verify all tests pass. 
    NOTE:
    If any of the terminal messages indicate a test has failed or the 
    message ‘‘spe down mode’’ is displayed, refer to 
    DEFINITY 
    Communications System Generic 1 and Generic 3i/s/vs 
    Maintenance
    , 555-204-105, to clear the trouble, or call your AT&T 
    representative. 
    						
    							A ctivate the System
    7-4September 1995 Issue 1  
    Screen 7-1. Typical Turn-On Messages for Systems with FLASH Memory
    2. About 2 minutes after REBOOT PERFORMED is displayed, verify the 
    terminal screen displays:
    Login:
    NOTE:
    Most red lights will come on and g o off a gain at this p oint.  Some red 
    lights will stay on until the country options are administered in the 
    next pages.
    Introduction to Terminal Screens and 
    Commands
    Screens
    The system is administered using screens displayed on the terminal. The 
    screens are used to add, change, display, list d ata, and to remove system and 
    telephone features. To access a screen, enter a valid system command in 
    response to the command: prompt.
     
           TN786 FLMM Release 1.8.0
           INVOKING EMERGENCY TRANSFER
            ROM CHECKSUM TEST ( = 9CAE )     PASSED
            SOFT INT TEST                    PASSED
            NMI TEST                         PASSED
            READ_WRITE MEMORY                PASSED
            MEMORY BOARD 1 PARITY BIT TEST   PASSED
            MEMORY FUNCTIONAL TEST           PASSED
            FLASH TEXT CHECKSUM ( = EF3E )   PASSED
           RESET 4 (REBOOT) PERFORMED   
    						
    							Log in to the System
    September 1995 Issue 1 
    7-5
    Commands
    System commands are standard words and phrases instructing the switch to 
    perform a specific function. The commands are arranged in hierarc hy of 
    keywords; that is, enter one command to take you to a different level. The 
    commands contain three parts: ACTION, OBJECT, and QUALIFIER.
    nACTION is the first p art of the c ommand. When command: appears on the 
    screen. The ACTION specifies the operation you want to do. Examples of 
    permissible entries include add, duplicate, change, remove, display, 
    list, and save.
    nOBJECT is the second part of the command and specifies the p articular 
    object you want to administer. Typical entries are hunt-group, coverage 
    path, and station.
    nQUALIFIER is the last part of the command. It is one or more words or 
    digits used to further identify or complete the OBJECT. For example, 
    hunt 
    group 15
     or station 3600, where 15 and 3600 are q ualifiers.
    An exam ple of the command line required to ad d a station with extension number 
    1234 is add station 1234. In this example, add is the ACTION, station is the 
    OBJECT, and 1234 is the QUALIFIER. In the c ommand line, spaces are required 
    between the ACTION, OBJECT, and QUALIFIER.
    To save time, enter enough letters for each part of the command to make it 
    unique. For example, if you want to enter the command change 
    system-parameters country-options, typing cha sys coun is acceptable.   
    However, typing the entire command will always work.
    NOTE:
    The craft login may not be allowed to perform some of the steps needed to 
    initialize the switch. If access is denied to some of these p rocedures, 
    contact your AT&T representative for assistance.
    Getting Help
    Use the HEL P key for a list of options and the CANCEL key to b a ck out of any 
    command.
    Log in to the System
    To log on the system, do the following:
    1. Verify the screen displays:
    Login:
    2. Type craft and press 
    ENT ER. 
    						
    							A ctivate the System
    7-6September 1995 Issue 1  
    3. Verify the screen displays:
    password:
    4. Type crftpw and press
     EN TER . For security reasons, the p assword is not 
    displayed as it is typed. The system verifies a valid login and password 
    name were entered. If an invalid login or p assword  name was entered, the 
    screen displays:
    login incorrect: 
    In this case, repeat the procedure using the correct login and matching 
    password.
    If the system recognizes the login and password name, the screen will 
    display the software version.
    5. Verify the screen display is similar to:
    Terminal Type (513, 715, 4410, 4425, VT220): [513] 
    6. Type the number of your management terminal and press 
    ENT ER. 
    7. Verify the screen displays:
    command:
    Set Required Country Options
    Certain country options need to be set to turn red failure indication lights off on 
    the circ uit packs.
    1. Verify the screen displays:
    command:
    2. Type change system-parameters country options and press 
    ENT ER .
    The following sc reen is displayed.  The cursor is set on Companding 
    Mode line. 
    						
    							Set Required  Country O ptions
    September 1995 Issue 1 
    7-7
    3. The default is Mu-Law.  If your country uses A-Law comp anding, type 
    A-Law.  If it uses Mu-Law and Mu-Law is displayed, go to Step 4 below. 
    Companding mode can b e A-law or Mu-law. The switch should have been 
    shipped with the correct Tone Detector circ uit packs for your country. If 
    you have TN420C you must use A-law.  If you have TN748 or TN756 you 
    must use  Mu-law. If you have TN2182, then your companding mode is 
    d i ctated b y your local practices.  Ad ministering the correct companding 
    mode will turn off any red lights on these c irc uit packs or on the tone-clock 
    boards (for examp le TN780).
    4. Press 
    ENTE R when this information is correct.
    Other items eventually need to b e entered on this screen, but this is all that 
    must be done to turn the red alarm indication lights off.  Refer to Table 7-1 
    for a list of the country codes.
    change system-parameters country-options               Page 1 of 21
    SYSTEM PARAMETERS COUNTRY-OPTIONS
             Companding Mode: A-Law           Base Tone Generator Set: 1
         440Hz PBX-dial Tone? n                   Secondary-dial Tone? n
           Digital Loss Plan: 1
      Analog Ringing Cadence: 1    Set Layer 1 timer T1 to 30 seconds? n
    Analog Line Transmission: 1
    TONE DETECTION PARAMETERS
    Tone Detection Mode: 5            Dial Tone Validation Timer 
    (msec):                      Interdigit Pause: 
    						
    							A ctivate the System
    7-8September 1995 Issue 1  
    5. If all the red lights do not go off, reseat (unplug and reinsert) any 
    purple-labeled circuit packs displaying red lights.
    !CAUTION:
    To avoid a disk crash, never reseat the DEFINITY  AUDIX System 
    without first shutting it d own. Shut down the DEFINITY AUDIX System 
    (and allow the disk to completely spin down) before unplugging the 
    DEFI NI TY AUDIX assembly. See Ap pendix C, DEFI NI TY AUDIX 
    System Power Procedures for the procedure for manually shutting 
    down and powering up DEFI NI TY AUDIX System. 
    !CAUTION:
    Before attempting to reseat white-labeled control circuit p acks or the 
    purple-labeled tone d etector/generator circuit pack (in the 
    single-carrier cabinet only), first power down the switch.
    6. If the red lights still do not go off, read the note below and then refer to 
    DEFI NI TY Com munications System Generic 1 and Generic 3i/s/vs 
    Maintenance
    , 555-204-105, to resolve the trouble, if necessary.
    NOTE:
    Ignore the red alarm indication light on the TN767 or TN464 DS1 
    circuit pack until after the Digital Service Level 1 (DS1) circuit pack is 
    administered.
    Table 7-1. Country Codes
    Country Country Code Country Country Code
    global 0 Spain 11
    USA 1 Fra n c e 12
    Australia 2 Germany 13
    Japan 3 Czechoslovakia 14
    Italy 4 Russia 15
    The Netherlands 5 Argentina 16
    Singapore 6 Greece 17
    Mexic o 7 China 18
    Belgium 8 Hong Kong 19
    Saudi Arabia 9 Thailan d 20
    United Kingdom 10 Macedonia 21 
    						
    							Change Craft Password
    September 1995 Issue 1 
    7-9
    Alarms will appear in the Alarm Log when power is applied to the system 
    before all equipment connecting to port circuit packs is installed. 
    Normally, some alarms will be logged when power is applied to the 
    system, but should be resolve d quickly. If no equipment is connected to 
    the port circuit packs, alarms associated with these ports can take u p to 
    four hours to log, but will clear automatically after all equipment is installed 
    and operating correctly.
    Change Craft Password
    The password for the craft login must be changed by the installing technician to 
    prevent unauthorized administration changes.
    !CAUTION:
    After the ‘‘craft’’ password is changed, the new password must b e 
    safeguarded so no unauthorized administration changes can be made. 
    This password MUST NOT  B E REV EA LED  t o t he customer or to any 
    unauthorized person.
    Passwords are changed using the Change Password Screen (see Screen 7-2). 
    To change the ‘‘craft’’ password, perform the following.
    1. Verify the screen displays:
    command:
    2.Type change password craft. Press 
    ENT ER. 
    						
    							A ctivate the System
    7-10September 1995 Issue 1  
    Screen 7-2. Typical Change Password Screen
    3. Verify the screen displays Change Password  Screen.
    Cursor is positioned on ‘‘Password for Login Making Change:”
    4. Type the password assigned to the craft login (assigned as 
    crftpw when 
    system is shipped) and press 
    ENT ER.
    Cursor is positioned on ‘‘Login’s Password:’’.
    5. Enter selected new password (see note below).
    NOTE:
    Valid passwords consist of a combination of from four to eleven 
    alpha or numeric characters. At least one letter and one number 
    must be used in each password.
    6. Press 
    ENTE R.
    Cursor is positioned on ‘‘Reenter Login’s Password:’’.
    7. Type new password again.
    8. Press 
    ENTE R.
    9. Verify the screen displays:
    command successfully completed 
    command:
      change password craft  Page 1 of 1
                                   PASSWORD ADMINISTRATION
    Password For Login Making Change:
    LOGIN BEING CHANGED
    Login Name: craft
    LOGIN’S PASSWORD INFORMATION
    Login’s Password:
    Reenter Login’s Password:  
    						
    							Set Date and Time
    September 1995 Issue 1 
    7-11
    Set Date and Time
    The system date and time are set using the Set Date and Time Screen (see 
    Screen 7-3). This screen is d isplayed on the terminal sc reen and is changed with 
    the terminal keyboard. To set the system time and date, p erform the following:
    1. Verify the screen displays:
    command:
    2. Type set time. Then press 
    ENTE R.
    3. Verify the screen displays Set Date and Time Screen (shown below).
    Cursor is positioned on Day of the Week: field.
    Screen 7-3. Typical Date and Time Screen
    4. Type 
    day of week in English (Sunday through Saturday) and press TA B to 
    move to next field.  See Table 7-2 for English day of the week names.
     set time                                        Page 1 of 1
       
                       DATE AND TIME
        
     DATE
        
       Day of the Week: _________     Month: __________
       Day of the Month: __             Year: ____
        
     TIME
        
                   Hour: __           Second: xx
                 Minute: __ 
    						
    							A ctivate the System
    7-12September 1995 Issue 1  
    Cursor is positioned on Month: field.
    5. Type c urrent month in English (January through December) and press TAB 
    to move to next field.  See Table 7-3 for English month names.
    Cursor is positioned on Year: field.
    Cursor is positioned on Day of the Month: field.
    Table 7-2. English Day of the Week Names
    Day Number Day Name
    1 Sunday
    2 Monday
    3 Tuesday
    4 Wednesday
    5 Thursday
    6 Friday
    7 Saturday
    Table 7-3.  English Month Names
    Month Number English Month Name
    1 January
    2 February
    3 March
    4April
    5May
    6 June
    7 July
    8 Au gust
    9 September
    10 October
    11 November
    12 December 
    						
    All ATT manuals Comments (0)

    Related Manuals for ATT DEFINITY Communications System Generic 3 For Single-Carrier Cabinets Instructions Manual