Home > ATT > Communications System > ATT DEFINITY Communications System Generic 3 For Single-Carrier Cabinets Instructions Manual

ATT DEFINITY Communications System Generic 3 For Single-Carrier Cabinets Instructions Manual

    Download as PDF Print this page Share this page

    Have a look at the manual ATT DEFINITY Communications System Generic 3 For Single-Carrier Cabinets Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 164 ATT manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Test Telephones and Other Equipment
    10-10Issue 1  September 1995  
    6. At the test telephone, hang up the receiver.
    7. On the attendant console, press Night key.
    8. Verify Night lamp  goes dark.
    Procedure—Ringing Device Not Installed
    1. Connect a spare 2500-typ e telephone to the information outlet indicated 
    on the console parameters screen.
    2. On the attendant console, press Night key.
    3. Verify Night lamp lights.
    4. Select a working telephone as the test telephone.
    5. At the test telephone, pick up the receiver, dial a trunk access code and 
    the listed  directory numb er for the attendant console.
    6. Verify ringing is heard on the spare telephone.
    7. At the test telephone, hang up the receiver.
    8. Disconnect the spare telephone from the information outlet.
    9. Press the Night key on the attendant console.
    10. Verify the Night lamp g oes off.
    11. Notify the customer that installation is complete and the external ringing 
    device can be installed.
    Test Queue Warning Indicator
    Description
    Make a test call to an extension associated with a Uniform Call Distribution (UCD) 
    or Direct Department Calling (DDC) group, and verify the queue warning 
    indicator lamp lights. If the queue warning indicator has not yet been installed by 
    customer, connect a spare telephone to the information outlet reserved for queue 
    warning indicator and make a test call.
    Procedure—Queue Warning Indicator Installed
    1. Administer Queue Warning Indicator number to 0 on Hunt Group Screen. 
    Record old number.
    2. Make sure all telephones in the group are disconnected or are “ busy.”
    3. Select a working telephone as the test telephone. 
    						
    							Test Queue Warning Indicator
    Issue 1  September 1995 
    10-11
    4. At the test telephone, pick up the receiver and d ial the numb er associated 
    with a uniform call d istribution (UCD) or a direct  department calling (DDC) 
    group.
    5. Verify the lamp  lights (see the following note).
    NOTE:
    Delay Recorded Announcement is heard if it is administered for this 
    group. The  delay announcement is followed by music if 
    Music-on-Hold is administered.
    6. At the test telephone, hang up the receiver.
    7. Administer queue warning threshold number to numb er changed in 
    Step 1.
    8. Restore service to all telephones made busy or disconnected in Step 2.
    Procedure—Queue Warning Indicator Not
    Installed
    1. Administer Queue Warning Indicator number to 0 on Hunt Group Screen. 
    Record old number.
    2. Make sure all telephones in the group are disconnected or are “ busy.”
    3. Connect a spare 2500-typ e telephone to an information outlet.
    4. Select a working telephone as the test telephone.
    5. At the test telephone, pick up the receiver and the dial numb er associated 
    with a uniform call d istribution (UCD) or a direct  department calling (DDC) 
    group.
    6. Verify ringing is heard on the spare telephone (see the following note).
    NOTE:
    Delay Recorded Announcement is heard at the test telephone if it is 
    administered for this group. The delay announcement is followed by 
    music if Music-on-Hold is administered.
    7. At the test telephone, hang up the receiver.
    8. Disconnect the spare telephone from the information outlet.
    9. Administer queue warning threshold number to numb er changed in 
    Step 1.
    10. Restore service to all telephones made busy or disconnected in Step 2. 
    Notify customer that installation is complete and that queue warning 
    indicator lamp  can be installed. 
    						
    							Test Telephones and Other Equipment
    10-12Issue 1  September 1995  
    Test Integrated Announcement
    Description
    The TN750 Announcement circuit pack provides the ability to store messages. 
    The mess a ges can be recorded from telephones on- or off-p remises and have 
    flexible message lengths.
    The telephone selected as the test telephone must have a c lass of service (COS) 
    with console permission enabled.
    Procedure — Record Announcement
    1. Select test telephone with console permission enabled. 
    2. Dial access code followed by the integrated announcement extension 
    number. Dial Tone is heard.
    3. Dial “1.” A short burst of tone is heard and recording begins.
    4. Speak the announcement into the telephone.
    5. When you have finished recording the announcement, dial “#” or hang up. 
    Recording stops and dial tone is heard.
    Procedure — Playback Announcement
    1. Dial access code followed by the integrated announcement extension 
    number. Dial Tone is heard.
    2. Dial “2.” The announcement is heard and dial tone is heard at comp letion 
    of announcement.
    Procedure —Delete Announcement
    1. Dial access code followed by the integrated announcement extension 
    number. Dial Tone is heard.
    2. Dial “3.” A confirmation tone is heard  and announcement is deleted. 
    						
    							Test Music-on-Hold
    Issue 1  September 1995 
    10-13
    Test Music-on-Hold
    Description
    Verify music is provided to a held party during any hold interval.
    Procedure
    1. Select a working telephone as the test telephone.
    2. At the test telephone, pick up the receiver and dial 0 for the attendant 
    console.
    3. At attendant console, answer call by pressing call appearance button (a 
    through f ) associated with the flashing Atnd lamp. The aud i ble alert 
    stops. Atnd lamp lights steadily.
    4. Press Hold at attendant console. The Hold lamp associated with the call 
    appearance button lights.
    5. Verify music is heard at the test telephone.
    6. Hang up the test telephone.
    Test Emergency Transfer
    Description
    Put system in emerg ency transfer mode and make call using emergency transfer 
    telephone.
    There may b e one, two, three, or four Emergency Transfer switches, d e pending 
    on the system configuration. The switch is located on the Processor circuit 
    pack(s) in the Processor Port Network (PPN) control carrier, and the switch is 
    located on the Maintenance circuit pack in the Expansion Port Network (EPN) 
    control carrier. 
    The Expansion Port Network (EPN) c a binets may be tested separately from the 
    Processor Port Network (PPN) c a binets in any system, b ut the Processor Port 
    Network (PPN) cabinets in a high or critical-reliability system must have b oth 
    switches set to the ON position to invoke Emergency Transfer. 
    						
    							Test Telephones and Other Equipment
    10-14Issue 1  September 1995  
    Procedure
    1. At c ontrol carrier, set Emergency Transfer switch(es) to ON p osition. See 
    Note.
    NOTE:
    Pull out on Switches to overc ome detents.
    2. At emergency transfer telephone connected to the port network being 
    tested, pick up the receiver and press Ground Start key, if so equi p ped. 
    Dial tone is heard.
    3. Dial numb er associated with an outside number. Audible ringing or busy 
    tone is heard.
    4. Hang up the test telephone.
    5. At control carrier, set Emergency Transfer switch(es) to AUTO position.
    Test Remote Access Interface (known 
    as Initialization and Administration 
    System)
    Description
    Test the communication link between the switch and Initialization and 
    Administration System (INADS) and verify the alarm notification process. Make a 
    remote test from Initialization and Administration System (INADS) to the system 
    and a local test from the system to Initialization and Administration System 
    (INADS).
    NOTE:
    In some countries, this remote access interface is not allowed. Check with 
    your AT&T representative.
    Procedure—Remote Test
    1. Call outside personnel who will be accessing the switch remotely to 
    perform a dministration, maintenance, and testing.
    2. Ask remote access p ersonnel to c all system and login and disp lay System 
    Parameters Maintenance sc reen. The login must be successful.
    NOTE:
    Requirement: Product Identification on the System Parameters 
    screen must match the Product Identification administered by the 
    local technician. 
    						
    							Test Basic Rate Interface (BRI)
    Issue 1  September 1995 
    10-15
    3. Remote access personnel enters test inads-link command, terminates 
    login, and disconnects.
    4. Remote access personnel then check the appropriate trouble ticket. The 
    trouble ticket should show ‘‘INADS,n,MINOR’’ in the description field to 
    indicate a minor off-board alarm was reported to the remote access 
    personnel. There may be additional text in the description field if other 
    resolved alarms were reported.
    5. Remote access personnel make second call and login to system and 
    checks the error log to verify no problems. See 
    DEFINITY Communications 
    System Generic 1 and Generic 3i/s/vs Maintenance
    , 555-204-105, or 
    DEFI NI TY Com munications System Generic 3r Maintenanc e, 
    555-230-105, for error log and error c o de information.
    6. Remote access personnel terminate login and disconnects.
    Procedure—Local Test
    1. Log in and enter test inads-link command.
    2. Request remote access personnel to verify a trouble ticket was created.
    3. Check error log to verify no problems.
    4. Log off the system.
    Test Basic Rate Interface (BRI)
    Description
    Check for normal voice telephone function (dial tone, ability to make and receive 
    calls). Check for the correct Service Profile Identifier (SPID) on a display 
    Telephone and the G3 Management Terminal (G3-MT).
    Procedure—Dial Tone
    1. Lift handset of Basic Rate Interface (BRI) telephone and listen for dial 
    tone.
    Procedure—Make and Receive Calls
    1. Select a working telephone with display and dial that telephone’s 
    extension number from the Basic Rate Interface (BRI) test telephone. The 
    called telephone rings.
    2. At the called telephone, pick up the receiver. Conversation must be 
    satisfactory. 
    						
    							Test Telephones and Other Equipment
    10-16Issue 1  September 1995  
    3. Verify the extension number of the calling telephone is displayed on the 
    display of the called telephone. The extension must be correct.
    4. Hang up both telephones.
    5. Call the Basic Rate  Interface (BRI) test telephone from the other 
    telephone. The Basic Rate Interface (BRI) test telephone rings.
    6. Verify the name and extension of the called Basic Rate Interface (BRI) test 
    telephone is correct as displayed on the calling telephone.
    7. Hang up both telephones.
    Procedure—Checking the Service Profile
    Identifier (SPID)
    This test requires a display telephone at the test telephone station.
    1. Use a ppropriate procedures to display the Service Profile Identifier (SPID) 
    on the test telephone. Procedures differ depending on the model of 
    telephone being used. The Service Profile Identifier (SPID) must be 
    correct. 
    						
    							Issue 1  September 1995 A-1 
    A
    Approved Grounds
    This chapter describes the approved grounds appropriate for the single-carrier 
    cabinets.
    Definition of Approved Ground
    An approved ground is the closest acceptable medium for grounding the 
    building entrance protector, entrance cable shield, or single-point ground of 
    electronic Private Branch Exchange (PBX) equipment. 
    If more than one type of ap proved ground is available on the premises, the 
    grounds must be bonded together as required in Section 250-81 of the National 
    Electrical Code (NEC), or the ap plicable code in your country. 
    Acceptable Mediums for Protective 
    Ground
    The following protective ground types are acceptable:
    Grounded Building Steel. — The metal frame of the building where it is 
    effectively grounded by one of the following grounds: acceptable metallic water 
    pipe, concrete encased ground, or a ground ring. 
    Acceptable Water Pipe. — A metal underground water p i pe, at least 1/2 inch 
    (1.3 c m) in d iameter, in d irect contact with the earth for at least 10 feet (3 meters). 
    The p i pe must be electrically continuous (or made electrically continuous by 
    bonding around insulated joints, plastic pipe, or plastic water meters), to the 
    point where the protector ground wire is connected. A metallic underground 
    water p ipe must be supplemented by the metal frame of the b uilding, a concrete  
    						
    							Approved Grounds
    A-2Issue 1  Septemb er 1995 
    encased ground, or a ground ring. If these grounds are not available, the water 
    pipe ground can be supplemented by one of the following types of grounds: 
    nOther local metal underground systems or structures — Local 
    underground structures such as tanks and piping systems
    nRod and pipe electrodes — A 5/8 inch (1.6 cm) (solid rod) or 3/4 inch
    (1.9 c m) (conduit or pipe) electrode driven to a minimum depth of 8 feet 
    (2.5 meters)
    nPlate electrodes — Must have a minimum of 2 square feet (0.6 sq. meter) 
    of metallic surface exposed to the exterior soil
    Concrete Encased Ground. — An electrode encased by at least 2 inches 
    (5 cm) of concrete and located within and near the bottom of a concrete 
    foundation or footing in direct contact with the earth. The electrode must be at 
    least 20 feet (6 meters) of one or more steel reinforcing bars or rods 1/2 inch 
    (1.3 c m) in diameter, or at least 20 feet (6 meters) of bare, solid copper, 
    4 AWG wire. 
    Ground Ring. — A buried ground that encircles a building or structure at a 
    d e pth of at least 2-1/2 feet (0.8 meter) b elow the earths surface. The ground ring 
    must be at least 20 feet (6 meters) of 2-AWG, bare, cop p er wire. 
    Approved Floor Grounds
    Approved floor grounds are those grounds on the floor of each high-rise building 
    suitable for c onnection to the ground terminal in the riser closet and to the Private 
    Branch Exchange (PBX) equipment single-point ground terminal. Approved floor 
    grounds may include the following: 
    nBuilding steel
    nThe grounding conductor for the secondary side of the power transformer 
    feeding the floor 
    nMetallic water pipes
    nPower feed metallic conduit supplying panel boards on the floor 
    nA grounding point specifically provided in the building for the purp ose
    !WARNING:
    If the approved ground or approved floor ground can only be accessed 
    inside a dedicated power equipment room, then connections to this ground 
    should be made by a licensed electrician. 
    NOTE:
    All protective grounds must b e electrically connected together to form a 
    single grounding electrode system.  
    						
    							Issue 1  Septemb er 1995 B-1 
    B
    Earthquake Protection Procedures
    This a p pendix describes earthquake protection installation procedures to 
    perform if your site experiences earthquake activity. 
    Use the following procedures to install earthquake protection for your c a binets.
    Install Floor Mounting to Attach 
    Cabinet to Floor
    Attach your DEFINITY System Generic 3 (G3) cabinets to the floor by completing 
    the following steps:
    1. Place the Front Mounting Angle at the location selected for the front of the 
    control cabinet. 
    2. Using the angle as the template, mark the location of the mounting bolts.
    3. Drill two holes 1/2-inch (1.3 c m) in diameter and 1-1/2 (3.8 cm) inches 
    deep at the spot marked in Step 2.
    4. Mount the Front Mounting An gle to the floor (see Figure B-1). 
    						
    All ATT manuals Comments (0)

    Related Manuals for ATT DEFINITY Communications System Generic 3 For Single-Carrier Cabinets Instructions Manual