Amanda Telephone Switches Instructions Manual

Chapter 6: Programming the NEC Electra, Level I 53
4. Press the LK4 key.
5. Do one of the following:
 Press 15 for CO/PBX Ring Assignment (Day Mode).
 Press 16 for CO/PBX Ring Assignment (Night Mode).
If you select 15 you can program both Day Mode and Night Mode during this 
same programming session. The 15 or 16 is the second number from the left on 
the display.
This places you in memory block 4-15 or 4-16—CO/PBX Ring Assignment.
The first two characters at the left end of the display is the...

54 Telephone Switching Systems for Amanda@SOHO
4. Press the FNC key again.
The FNC key’s light goes off.
To cancel Call Forward—Busy/No Answer:
1. Press the FNC key.
The FNC key’s light goes on.
2. Press 62.
3. Press the FNC key again.
The FNC key’s light goes off.
To set Call Forward—All Calls:
1. Press the FNC key.
The FNC key’s light goes on.
2. Press 61.
3. Enter the destination station number.
4. Press the FNC key again.
The FNC key’s light goes off.
To cancel Call Forward—All Calls:
1. Press the...

Chapter 6: Programming the NEC Electra, Level I 55
NEC Electra, Level I (release 2.00+) 
####################################################
# NEC Electra Level 1                              #
####################################################
dl_dtwait F-         # Dial code to put a caller on transfer hold         :
dl_ndtret -          # Dial code to use when there is no transfer dialtone:
dl_rnaret F-         # Dial code to return to caller after Ring No Answer :
dl_bsyret F-         # Dial code...

56 Telephone Switching Systems for Amanda@SOHO 

Chapter 7:
Programming the NEC Electra II
Getting Started
This chapter cover the NEC Electra II, software release 3.0 and later.
To connect Amanda@SOHO to an NEC Electra II, you need one SLI-8G-21 single-line 
interface card (this works for up to eight analog voice mail ports).
Run one pair wire for each voice mail port from the punch down block to the connector on 
the SLI.
Once the two are connected, you are ready to program the NEC Electra II. The 
programming can be done from any station—so long as...

58 Installing and Administering Amanda@SOHO
4. Press the TRF key to write the setting to the database and move on to the next data 
setting. For example, after providing a setting for port one or feature one, you move 
on to port two or feature two. When you reach the last port or feature, you move on to 
the next memory block. For example, you would move from memory block 4-14 to 4-
15.
5. Press the SPKR key to stop programming.
The following diagram shows a typical telephone set with its display and...

Chapter 7: Programming the NEC Electra II 59
Programming Voice Mail Access
The hunt group should be circular.
To program voice mail access:
1. Press the FNC key.
2. Press #0*8974.
3. To learn what physical port number is the first voice mail port:
a. Press the LK7 key.
b. Press 1.
This puts you in memory block 7-1, the card interface slot assignment.
c. Press the TRF key until the unit name SLI8G-21 appears on the display.
The first port on this card is on the lower right of the display. It is a...

60 Installing and Administering Amanda@SOHO
Programming the Hunt Group
The hunt group should be circular.
To program the Intercom Master Hunt Number:
1. Press the LK4 key.
2. Press 14.
This puts you in memory block 4-14, Intercom Master Hunt Number.
3. Go to the Tel Port No. and type the two-digit port number for the first port (for exam-
ple, 25.)
4. Press LK2 to modify the displayed setting to YES.
5. Press the TRF key to enter.
Programming sample:
Tel Port No.    Data No.    Title    Setting Data.
25/...

Chapter 7: Programming the NEC Electra II 61
Programming sample:
Tel Port No.    Data No.    Title    Setting Data.
25/ _______14___ICMFWD__ 303
9. Press the TRF key.
10. Repeat steps D through G for the rest of the voice mail ports in the hunt group.? for 
the rest of the extension in the hunt group?
Programming a Quick Transfer
To set the quick transfer to the extension for the first port:
1. Press the LK1 key.
2. Press 8.
This puts you in memory block 1-8.
3. Enter the extension (for example, 300) for...

62 Installing and Administering Amanda@SOHO
4. To change the field to 7*:
a. Press 7.
b. Press the LNR/SPD key.
c. Press #.
5. Type 502 (to set MWI).
Programming sample:
                       Dial code field        Function number
47:__2DG_____(7*
) =       502
TIME    DISPLAY
6. Press the TRF key to save your change.
The Dial code field should be 7#, which is what you need for canceling the message 
waiting indicator.
7. Type 503 (to cancel MWI).
Programming sample:
                       Dial code...