2012 Na Yamaha Super Tenere Manual

haha CABLE ROUTING
2-60
1. Headlight relay
2. Turn signal/hazard relay
3. Radiator fan motor relay
4. Main fuse
5. Starting circuit cut-off relay
6. Rectifier/regulator coupler
7. Stator coil coupler
8. Joint coupler
9. Battery
10. Positive battery lead
11. Crankshaft position sensor coupler
12. Negative battery lead coupler
13. Negative battery lead
14. Starter relay
15. Fuse box 1
16. Fuse box 2
17. Grip warmer coupler
18. Accessory light coupler
19. Left handlebar switch coupler
20. Stator coil lead...

haha CABLE ROUTING
2-61
Electrical components tray (right side view)
AA
A
B
C
D
E
J
F
F
K
L
MN
123456
7
8
9
10
11
12
13
15
16
17
1819
20
20
21
22
23
24
25
26
30
33
20
31
32
34
34
35
36
10
37
3730
S
R
O
PQ
G
14
H
I
1314
T
U
AB
V
W
X
Z
27
28
29
Y
AC
AD
AE
AFAG13
AH
11
12
AI
AJ
AK
AL  

haha CABLE ROUTING
2-62
AA. Route the stator coil lead over the wire harness.
AB. Fasten the stator coil lead, wire harness, wire  harness (starting circuit cut-off relay lead and 
starter relay lead), and wire harness 
(rectifier/regulator lead and stator coil lead) with 
the plastic band. Route the leads in the order 
shown in the illustration. Point the end of the plastic 
band downward. Do not cut off the excess end of 
the plastic band.
AC. Position the rubber cover at the location shown in  the...

haha CABLE ROUTING
2-63
Engine (right side view)
A
12
3456
3
3
4
5
5
C
E
F
B
6
7
G
D  

haha CABLE ROUTING
2-64
1. Brake hose (hydraulic unit to rear brake caliper)
2. Rear wheel sensor lead
3. O 2 sensor #1 lead
4.

O 2 sensor #2 lead
5

. Crankshaft position sensor lead
6. Rear brake light switch lead
7. Footrest plate
A. Route the crankshaft position sensor lead to the  front of the O 2 sensor #1 lead, and then fasten the 
lead

s with the holder.
B. Make sure that there is no slack in the crankshaft  position sensor lead.
C. Route the rear brake light switch lead to the inside  of the...

haha CABLE ROUTING
2-65
Rear brake hose (right side view)
A
B
1
1
1
2
22
3
3
5
45
4
5
4
5
4
5
45
4
4
5
5
C
D
E
F
G
K
LM
HI
I
J  

haha CABLE ROUTING
2-66
1. Brake fluid reservoir hose
2. Brake hose (rear brake master cylinder to  hydraulic unit)
3. Rear brake light switch lead
4. Brake hose (hydraulic unit to rear brake caliper)
5. Rear wheel sensor lead
A. Install the brake fluid reservoir hose onto the hose  fitting of the brake fluid reservoir, making sure that 
the hose contacts the reservoir.
B. Fasten the brake hose (rear brake master cylinder  to hydraulic unit) with the holder. Position the 
holder 20 –40 mm (0.79 –1.57...

haha CABLE ROUTING
2-67
Throttle bodies (top view)
A
B
C
DF
D1
3
2
45
8
8
6
7
8
9
14
1110
15
12
E
16
13
17
2419
2120
2223
G
H
I
J
18  

haha CABLE ROUTING
2-68
1. Cylinder-#1 left ignition coil lead
2. Accelerator position sensor lead
3. Cylinder-#1 right ignition coil lead (white tape)
4. Cylinder-#2 left ignition coil lead
5. Cylinder-#2 right ignition coil lead (white tape)
6. Throttle servo motor lead (yellow tape)
7. Throttle position sensor lead
8. Wire harness
9. Canister purge hose (throttle body to hose joint)
10. Coolant temperature sensor lead
11. Injector #2 lead
12. Canister purge hose (hose joint to canister)
13. Injector...

haha CABLE ROUTING
2-69
Hydraulic unit assembly (top view)
A
B
C
D
2
2
12
4
3
6
8
9
16
17
N
12
H
16
1718
18
19
19
G
F
E
14
5
5
5
4
1110
7
13
15
15
11
K
I
L
M
O
J