2012 Na Yamaha Super Tenere Manual

haha CHASSIS SPECIFICATIONS
2-10
EAS20300
CHASSIS SPECIFICATIONS
Chassis Frame type Backbone
Caster angle 28.00°
Trail 126.0 mm (4.96 in)
Front wheel
Wheel type Spoke wheel
Rim size 19M/C × MT2.50
Rim material Aluminum
Wheel travel 190.0 mm (7.48 in)
Radial wheel runout limit 2.0 mm (0.08 in)
Lateral wheel runout limit 2.0 mm (0.08 in)
Rear wheel
Wheel type Spoke wheel
Rim size 17M/C × MT4.00
Rim material Aluminum
Wheel travel 190.0 mm (7.48 in)
Radial wheel runout limit 2.0 mm (0.08 in)
Lateral wheel...

haha CHASSIS SPECIFICATIONS
2-11
Front disc brake Disc outside diameter  × thickness 310.0  × 4.5 mm (12.20  × 0.18 in)
Brake disc thickness limit 4.0 mm (0.16 in)
Brake disc deflection limit 0.10 mm (0.0039 in)
Brake pad lining thickness (inner) 4.5 mm (0.18 in)
Limit 0.5 mm (0.02 in)
Brake pad lining thickness (outer) 4.5 mm (0.18 in)
Limit 0.5 mm (0.02 in)
Master cylinder inside diameter 16.00 mm (0.63 in)
Caliper cylinder inside diameter 30.23 mm (1.19 in)
Caliper cylinder inside diameter 27.00 mm...

haha CHASSIS SPECIFICATIONS
2-12
Quantity 485.0 cm³ (16.40 US oz, 17.11 Imp.oz)
Level 150.0 mm (5.91 in)
Spring preload adjusting positions
Minimum 8
Standard 5.5
Maximum 0
Rebound damping adjusting positions *With the adjusting screw fully turned in
Minimum 10 click(s) out*
Standard 8 click(s) out*
Maximum 1 click(s) out*
Compression damping adjusting positions
*With the adjusting screw fully turned in
Minimum 13 click(s) out*
Standard 6 click(s) out*
Maximum 1 click(s) out*
Rear suspension
Type...

haha ELECTRICAL SPECIFICATIONS
2-13
EAS20310
ELECTRICAL SPECIFICATIONS
Voltage System voltage 12 V
Ignition systemIgnition system TCI
Ignition timing (B.T.D.C.) 5.0 °/1100 r/min
Engine control unit
Model/manufacturer TBDFD6/DENSO
Ignition coilMinimum ignition spark gap 6.0 mm (0.24 in)
Primary coil resistance 1.19–1.61  
Secondary coil resistance 8.50–11.50 k 
AC magneto
Standard output 14.0 V, 42.9 A at 5000 r/min
Stator coil resistance 0.112– 0.168  at 20 °C (68 °F)
Rectifier/regulator
Regulator type...

haha ELECTRICAL SPECIFICATIONS
2-14
Traction control system indicator light LED
Electric starting system
System type Constant mesh
Starter motor
Power output 0.75 kW
Armature coil resistance 0.0100– 0.0200 
Brush overall length 12.0 mm (0.47 in)
Limit 6.50 mm (0.26 in)
Brush spring force 6.02 –6.51 N (614 –664 gf, 21.69 –23.45 oz)
Mica undercut (depth) 0.70 mm (0.03 in)
Starter relay Amperage 180.0 A
Coil resistance 4.18 –4.62  
Horn
Horn type Plane
Quantity 1 pc
Maximum amperage 3.0 A
Turn...

haha ELECTRICAL SPECIFICATIONS
2-15
Accessory light fuse (OPTION) 20.0 A
Spare fuse 30.0 A
Spare fuse 20.0 A
Spare fuse 15.0 A
Spare fuse 10.0 A
Spare fuse 7.5 A
Spare fuse 3.0 A  

haha TIGHTENING TORQUES
2-16
EAS20320
TIGHTENING TORQUES
EAS20331
GENERAL TIGHTENING TORQUE 
SPECIFICATIONS
This chart specifies tightening torques for stan-
dard fasteners with a standard ISO thread pitch. 
Tightening torque specifications for special com-
ponents or assemblies are provided for each 
chapter of this manual. To avoid warpage, tight-
en multi-fastener assemblies in a crisscross pat-
tern and progressive stages until the specified 
tightening torque is reached. Unless otherwise...

haha TIGHTENING TORQUES
2-17
EAS20340
ENGINE TIGHTENING TORQUES Item Thread 
size Q’
ty Tightening torque Remarks
Exhaust pipe nut M8 4 20 Nm (2.0 m·kgf, 14 ft ·lbf)
Exhaust pipe bolt M8 1 20 Nm (2.0 m·kgf, 14 ft ·lbf)
Exhaust pipe protector screw M6 2 8 Nm (0.8 m ·kgf, 5.8 ft ·lbf)
Exhaust pipe joint bolt M8 1 20 Nm (2.0 m·kgf, 14 ft ·lbf)
O 2 sensor
M18 2 45 Nm (4.5 m·kgf, 33 ft ·lbf)
Muffler bolt M10 1 47 Nm (4.7 m·kgf, 34 ft ·lbf)
Muffler cover bolt M6 2 7 Nm (0.7 m·kgf, 5.1 ft ·lbf)
Muffler cover...

haha TIGHTENING TORQUES
2-18
Water pump inlet hose clamp 
screw (water pump side) M6 1 2.5 Nm (0.25 m
·kgf, 1.8 ft ·lbf)
Water pump housing cover bolt M6 1 10 Nm (1.0 m ·kgf, 7.2 ft ·lbf)
Coolant drain bolt (water pump) M6 1 10 Nm (1.0 m ·kgf, 7.2 ft ·lbf)
Generator cover bolt  M6 2 12 Nm (1.2 m ·kgf, 8.7 ft ·lbf) l=55 mm 
(2.17 in) 
Generator cover bolt  M6 12 12 Nm (1.2 m ·kgf, 8.7 ft ·lbf) l=25 mm 
(0.99 in)
Generator rotor bolt  M12 1 130 Nm (13 m·kgf, 94 ft· lbf)
Stator coil bolt M6 3 10 Nm (1.0...

haha TIGHTENING TORQUES
2-19
Rear balancer shaft retainer 
screw M6 1 12 Nm (1.2 m
·kgf, 8.7 ft ·lbf)
Rear balancer holder bolt M6 1 10 Nm (1.0 m ·kgf, 7.2 ft ·lbf)
Crankcase bolt  M10 6 See TIP.l=130 mm 
(5.12 in)
Crankcase bolt  M8 6 24 Nm (2.4 m·kgf, 17 ft ·lbf) l=78 mm 
(3.07 in)
Crankcase bolt  M8 7 24 Nm (2.4 m·kgf, 17 ft ·lbf) l=80 mm 
(3.15 in)
Crankcase bolt  M8 5 24 Nm (2.4 m·kgf, 17 ft ·lbf) l=60 mm 
(2.36 in)
Crankcase bolt  M6 6 10 Nm (1.0 m·kgf, 7.2 ft ·lbf) l=50 mm 
(1.97 in)
Crankcase...