2012 Na Yamaha Super Tenere Manual

haha 4
CHASSIS
GENERAL CHASSIS ....................................................................................... 4-1
INSTALLING THE SEATS........................................................................\
. 4-2
INSTALLING THE CARRIERS .................................................................. 4-2
REMOVING THE ABS UNIT COVER ....................................................... 4-7
INSTALLING THE ABS UNIT COVER ...................................................... 4-7
REMOVING THE...

haha REAR BRAKE............................................................................................... 4-51
INTRODUCTION ..................................................................................... 4-58
CHECKING THE REAR BRAKE DISC.................................................... 4-58
REPLACING THE REAR BRAKE PADS................................................. 4-58
REMOVING THE REAR BRAKE CALIPER ............................................ 4-59
DISASSEMBLING THE REAR BRAKE CALIPER...

haha SWINGARM................................................................................................... 4-99
REMOVING THE SWINGARM.............................................................. 4-101
CHECKING THE SWINGARM .............................................................. 4-101
INSTALLING THE SWINGARM ............................................................ 4-101
SHAFT DRIVE ............................................................................................. 4-103...

haha GENERAL CHASSIS
4-1
EAS21830
GENERAL CHASSIS Removing the seats and carriers
Order Job/Parts to remove Q ’ty Remarks
1 Rider seat 1
2 Hexagon wrench 1
3 Passenger seat 1
4 Rider seat height position adjuster 1
5 Standard carrier 1
6 Standard carrier bracket 1
7 Left grab bar 1
8 Right grab bar 1
9 Additional carrier 1
10 Seat bracket 1
For installation, reverse the removal proce-
dure.
8 6
2 1
4 3
7
(4)
5
9
10
20 Nm (2.0 m 
kgf, 14 ft 
Ibf)T.R.
20 Nm (2.0 m 
kgf, 14 ft 
Ibf)T.R.
32 Nm (3.2 m ...

haha GENERAL CHASSIS
4-2
EAS23P1003
INSTALLING THE SEATS
1. Install: Passenger seat  “1”
TIP
Insert the projection “a”  on the rear of the pas-
senger seat into the seat holder  “b” in the addi-
tional carrier.
2. Install:
Rider seat height position adjuster  “1”
 Rider seat “2”
TIP
The rider seat height can be adjusted to one of 
two positions to suit the rider ’s preference.
▼▼▼▼ ▼ ▼▼▼ ▼▼▼▼▼ ▼ ▼ ▼▼▼▼ ▼ ▼▼▼▼ ▼ ▼▼▼ ▼▼▼▼
To install the rider seat in the high posi-
tion
a. Install the rider seat height...

haha GENERAL CHASSIS
4-3
Standard carrier
Additional carrier
1. Install: Seat bracket  “1”
TIP
Make sure that the spring nuts  “2” contact the 
edges “a”  of the recesses in the seat bracket.
Temporarily tighten the seat bracket bolts “3”.
2. Install: Additional carrier  “1”
TIP
Temporarily tighten the additional carrier bolts 
“2”. 3. Tighten:
 Seat bracket bolts  “1”
  Additional carrier bolts  “2”
TIP
Before tightening the bolts, make sure to align 
the bolt holes “a” in the additional carrier...

haha GENERAL CHASSIS
4-4
TIP
Align the slots  “a” in the washer with the projec-
tions “b”  on the grab bar.
5. Remove: Rubber plug “1”
6. Install: Standard carrier  “1”
TIP
Use the two standard carrier bracket bolts  “2” 
and the standard carrier bolt (45 mm) “3”.
T R.. Standard carrier bolt
20 Nm (2.0 m· kgf, 14 ft·lbf)
1
2 a
b
1
3
1
2  

haha GENERAL CHASSIS
4-5
Removing the tail/brake light assembly Order Job/Parts to remove Q ’ty Remarks
Rear fuel tank bracket/Seat lock assembly Refer to  “FUEL TANK” on page 7-1.
Standard carrier bracket/Seat bracket Refer to  “Removing the seats and carriers”.
1 ABS unit cover 1
2 Rear turn signal light coupler 2 Disconnect.
3 License plate light coupler 1 Disconnect.
4 Tail/brake light coupler 1 Disconnect.
5 Tail/brake light assembly 1
6 Lean angle sensor coupler 1 Disconnect.
7 Lean angle sensor...

haha GENERAL CHASSIS
4-6
Removing the tail/brake light assembly Order Job/Parts to remove Q ’ty Remarks
11 Seat lock cable 1
12 Seat lock bracket 1
13 Seat lock 1
For installation, reverse the removal proce-
dure.
11
12
13
7 Nm (0.7 m 
kgf, 5.1 ft 
Ibf)T.R.
7 Nm (0.7 m 
kgf, 5.1 ft 
Ibf)T.R.
15 Nm (1.5 m 
kgf, 11 ft 
Ibf)T.R.
15 Nm (1.5 m 
kgf, 11 ft 
Ibf)T.R.
1.0 Nm (0.10 m 
kgf, 0.72 ft 
Ibf)T.R.
3.0 Nm (0.30 m 
kgf, 2.2 ft 
Ibf)T.R.  

haha GENERAL CHASSIS
4-7
EAS23P1103
REMOVING THE ABS UNIT COVER
1. Remove: ABS unit cover  “1”
TIP
Remove the quick fastener screw  “2”, and then 
pull the ABS unit cover off as shown in the illus-
tration.
EAS23P1068
INSTALLING THE ABS UNIT COVER
1. Install: Frame ground lead  “1”
TIP
Make sure that the frame ground lead terminal 
“a” contacts the stopper  “b” on the frame.
2. Install: Plastic locking tie  “1”
TIP
Fold the ABS test coupler lead  “2”, and then 
fasten the ABS test coupler lead, lean...