2012 Na Yamaha Super Tenere Manual

haha FRONT WHEEL
4-28
▼▼▼▼ ▼ ▼▼▼ ▼▼▼▼▼ ▼ ▼ ▼▼▼▼ ▼ ▼▼▼▼ ▼ ▼▼▼ ▼▼▼▼
a. Insert the front wheel axle from the right side 
and tighten it to 72 Nm (7.2 m ·kgf, 52 ft ·lbf).
b. In the order pinch bolt  “1”  pinch bolt  “2”  
pinch bolt  “1”, tighten each bolt to 21 Nm (2.1 
m· kgf, 15 ft ·lbf) without performing temporary 
tightening.
▲▲▲▲ ▲ ▲▲▲ ▲▲▲▲▲ ▲ ▲ ▲▲▲▲ ▲ ▲▲▲▲ ▲ ▲▲▲ ▲▲▲▲
6. Measure:
TIP
Measure the distance  “a” only if the wheel bear-
ings, wheel sensor rotor, or both were replaced.
Distance  “a”...

haha REAR WHEEL
4-29
EAS22030
REAR WHEEL Removing the rear wheel sensor, rear wheel and brake disc
Order Job/Parts to remove Q ’ty Remarks
Fuel tank Refer to “FUEL TANK ” on page 7-1.
1 Rear wheel sensor coupler 1 Disconnect.
2 Rear brake hose holder 2
3 Rear wheel sensor 1
4 Rear wheel axle pinch bolt 1 Loosen.
5 Rear wheel axle nut 1
6 Brake torque rod 1
7 Rear wheel axle 1
8 Rear brake caliper 1
9 Rear wheel 1
10 Rear wheel sensor housing 1
11 Collar 1
1
9
11
10
5
(6)
8
3
7
6
4
2
2
LS
New
LT
7 Nm...

haha REAR WHEEL
4-30
Removing the rear wheel sensor, rear wheel and brake disc Order Job/Parts to remove Q ’ty Remarks
12 Rear brake disc cover 1
13 Rear brake disc 1
For installation, reverse the removal proce-
dure.
13
12
(6)
LS
New
LT
7 Nm (0.7 m
kgf, 5.1 ft 
Ibf)T.R.7 Nm (0.7 m 
kgf, 5.1 ft 
Ibf)T.R.
23 Nm (2.3 m 
kgf, 17 ft 
Ibf)T.R.
25 Nm (2.5 m 
kgf, 18 ft 
Ibf)T.R.
30 Nm (3.0 m 
kgf, 22 ft 
Ibf)T.R.
125 Nm (12.5 m 
kgf, 90 ft 
lbf)T.R.  

haha REAR WHEEL
4-31
Disassembling the rear wheel Order Job/Parts to remove Q ’ty Remarks
1 Dust seal 1
2 Rear wheel drive hub 1
3 Wheel bearing 1
4Collar 1
5 Rear wheel drive hub damper 6
6 Bearing 1
7 Spacer 1
8 Rear wheel sensor rotor 1
9 Oil seal 1
10 Wheel bearing 1
For assembly, reverse the disassembly pro-
cedure.
132
4
5
6
10
8(5)
9
7
New
New
New
LS
8 Nm (0.8 m

kgf, 5.8 ft 
Ibf)T.R.
LS
LT  

haha REAR WHEEL
4-32
EAS22050
REMOVING THE REAR WHEEL
NOTICE
ECA23P1013
Keep magnets (including magnetic pick-up 
tools, magnetic screwdrivers, etc.) away 
from the rear wheel hub  “1”, otherwise the 
wheel sensor rotor equipped in the wheel 
hub may be damaged, resulting in improper 
performance of the ABS system.
1. Stand the vehicle on a level surface.
WARNING
EWA13120
Securely support the vehicle so that there is 
no danger of it falling over.
TIP
Place the vehicle on the centerstand so that the...

haha REAR WHEEL
4-33
 Oil seal
Refer to  “CHECKING THE FRONT WHEEL ” 
on page 4-23.
2. Check: Tire
 Rear wheel
Damage/wear   Replace.
Refer to  “CHECKING THE TIRES ” on page 
3-17 and “ CHECKING THE WHEELS ” on 
page 3-16.
3. Check: Spokes
Refer to  “CHECKING AND TIGHTENING 
THE SPOKES ” on page 3-16.
4. Measure:
Radial wheel runout
 Lateral wheel runout
Refer to  “CHECKING THE FRONT WHEEL ” 
on page 4-23.
EAS22200
MAINTENANCE OF THE REAR WHEEL 
SENSOR AND SENSOR ROTOR
NOTICE
ECA23P1016
 Handle...

haha REAR WHEEL
4-34
▲▲▲▲ ▲ ▲▲▲ ▲▲▲▲▲ ▲ ▲ ▲▲▲▲ ▲ ▲▲▲▲ ▲ ▲▲▲ ▲▲▲▲
2. Install: Rear wheel sensor rotor
NOTICE
ECA23P1019
Replace the wheel sensor rotor bolts with 
new ones.
3. Measure:
Wheel sensor rotor deflection
Out of specification   Correct the wheel sen-
sor rotor deflection or replace the wheel sen-
sor rotor.
Refer to  “MAINTENANCE OF THE REAR 
WHEEL SENSOR AND SENSOR ROTOR ” 
on page 4-33.
EAS22150
ADJUSTING THE REAR WHEEL STATIC 
BALANCE
TIP
 After replacing the tire, wheel or both, the rear...

haha REAR WHEEL
4-35
5. Tighten: Brake torque rod bolts
 Rear wheel axle nut
 Rear wheel axle pinch bolt
6. Measure:
TIP
Measure the distance  “a” only if the wheel bear-
ings, wheel sensor rotor, or both were replaced.
Distance  “a”
(between the wheel sensor rotor “1”  and 
wheel sensor housing “2”)
Out of specification   Reinstall the bearing 
or replace the wheel sensor rotor.
7. Install: Rear wheel sensor
NOTICE
ECA23P1017
To route the rear wheel sensor lead, refer to 
“CABLE ROUTING ” on page...

haha FRONT BRAKE
4-36
EAS22210
FRONT BRAKE Removing the front brake pads
Order Job/Parts to remove Q ’ty Remarks
The following procedure applies to both of 
the front brake calipers.
1 Brake pad clip 2
2 Brake pad pin 1
3 Brake pad spring 1
4 Front brake pad 2
5 Front brake hose holder 1 Left side only.
6 Front reflector 1
7 Front wheel sensor lead holder 1 Left side only.
8 Front brake caliper 1
9 Bleed screw 1 Left brake caliper side.
10 Bleed screw 1 Right brake caliper side.
For installation,...

haha FRONT BRAKE
4-37
Removing the front brake master cylinder Order Job/Parts to remove Q ’ty Remarks
Brake fluid Drain.
Refer to 
“BLEEDING THE HYDRAULIC 
BRAKE SYSTEM (ABS) ” on page 3-14.
1 Hand shield 1
2 Grip end 1
3 Rear view mirror 1
4 Upper hand shield bracket 1
5 Brake master cylinder reservoir cap 1
6 Brake master cylinder reservoir diaphragm hold-
er 1
7 Brake master cylinder reservoir diaphragm 1
8 Lower hand shield bracket 1
9Brake  lever 1
8
1
2
3
4
9
7
6
5
S
LT
10 Nm (1.0 m
kgf, 7.2 ft...