Xerox WorkCentre PE120 User Manual

							D
Your machine is a full-featured laser printer that has been 
optimized to meet most of your printing needs. Recognizing 
that each user may have different requirements, however, 
Xerox makes several options available to enhance your 
machine’s capabilities.
This chapter includes:
• Installing Memory DIMM
• Installing an Optional Tray
INSTALLING MACHINE 
O
PTIONS
Downloaded From ManualsPrinter.com Manuals 
						

							Installing Machine OptionsD.2
Installing Memory DIMM
Your machine has a dual in-line memory module (DIMM) slot. 
Use this DIMM slot to install more memory option for the 
machine.
NOTE: Your machine has 32 MB of memory which can be 
expanded to 160 MB. Use only a Xerox-approved DIMM. Contact 
your Xerox dealer.
CAUTION: Static electricity can damage DIMMs. When handling a 
DIMM, either wear an antistatic wrist strap, or frequently touch the 
surface of the DIMM antistatic package and then touch bare metal 
on the machine.
1Turn the machine off and unplug all cables and the power 
cord from the machine.
2Hold the control board cover and remove it.
3Completely open the latches on each side of the DIMM slot.
Downloaded From ManualsPrinter.com Manuals 
						

							Installing Machine OptionsD.3
D
4Remove the memory DIMM from its antistatic package. 
Locate the alignment notches on the bottom edge of each 
DIMM.
5Holding the memory DIMM by the edges, align the notches 
on the memory DIMM with the grooves at the top of the 
memory DIMM slot.
6Push the DIMM straight into the DIMM slot until it snaps into 
place. Make sure the latches fit over the notches located on 
either side of the DIMM.
Connection
points
Notches
Groove
Notch
LatchNotch
Downloaded From ManualsPrinter.com Manuals 
						

							Installing Machine OptionsD.4
7Replace the control board cover. 
8Reconnect the power cord and printer cable, and turn the 
machine on.
NOTE: After installing the memory DIMM, you need to select it in 
the printer properties of the PostScript printer driver so that 
you can use it with your machine (
WorkCentre PE120i only):
1. Make sure that the PostScript printer driver is installed in your 
computer. For details about installing the PS printer driver, see 
page B.2.
2. Click the Windows 
Start menu.
3. For Windows 95/98/Me/NT 4.0/2000, select 
Settings and then 
Printers.
For Windows XP, select 
Printers and Faxes.
4. Select the 
Xerox WC PE120 Series PS printer.
5. Click the right mouse button on the machine icon and select 
Properties.
6. For Windows 95/98/Me, select 
Device Options tab.
For Windows NT 4.0/2000/XP, select 
Device Settings tab.
7. Select the memory DIMM you installed in from 
Printer 
Memory 
in the Installable Option section and click OK.
For Windows 98, select 
Installable Option → VMOption → 
change setting for:VMOption → change memory .
Downloaded From ManualsPrinter.com Manuals 
						

							Installing Machine OptionsD.5
D
Removing a Memory DIMM
1Follow steps 1 through 2 on page D.2 to access the control 
board.
2Push the latches at both ends of the DIMM slot away from 
the DIMM. Pull out the DIMM.
3Place the DIMM in its original packaging or wrap it with a 
sheet of thin metal, such as aluminium foil, and store it in a 
box.
4Follow from step 7 on page D.4.
Downloaded From ManualsPrinter.com Manuals 
						

							Installing Machine OptionsD.6
Installing an Optional Tray
You can increase the paper handling capacity of your machine 
by installing an optional Tray 2. This tray holds 250 sheets of 
paper. 
1Turn the machine off and unplug all cables from the 
machine.
2Remove the packing material from the tray and remove the 
tape fixing the interface cable to the tray.
3Find the location of the connector and the optional tray 
positioners.
Downloaded From ManualsPrinter.com Manuals 
						

							Installing Machine OptionsD.7
D
4Place the machine over the tray, aligning the feet on the 
machine with the positioners in the tray.
5Plug the interface cable of the tray into the connector on the 
back of the machine. 
6Load paper in the tray. The instructions for loading paper in 
this tray are the same as for loading the standard paper 
tray. See page 2.7.
7After loading paper, you need to set the paper type and size 
for Tray 2. See page 2.21.
8Reconnect the power cord and cables and then turn the 
machine on.
Lifting handles are 
located at the lower 
edge of both sides of 
the machine.
Downloaded From ManualsPrinter.com Manuals 
						

							Installing Machine OptionsD.8
Setting Tray 2 in the Printer Properties
If you installed Tray 2 with your machine on, the machine does 
not recognize it. In this case, you need to set the tray in the 
printer properties window so that you can use it for PC printing.  
The procedure for setting the tray may differ depending on the 
selected printer driver.
To set the tray in the printer properties of the PCL 6 printer 
driver:
1Click the Windows Start menu.
2For Windows 98/Me/NT 4.0/2000, select Settings and then 
Printers.
For Windows XP, select 
Printers and Faxes.
3Select the Xerox WC PE120 Series PCL 6 icon.
4Click the right mouse button on the machine icon and select 
Properties.
5Click the Printer Configuration tab, and select Tray 2 
from the 
Optional Tray drop-down list.
6Click OK.
To set the tray in the printer properties of the PostScript printer 
driver (WorkCentre PE120i only).
1Click the Windows Start menu.
2For Windows 95/98/Me/NT 4.0/2000, select Settings and 
then 
Printers.
For Windows XP, select Printers and Faxes.
3Select the Xerox WC PE120 Series PS machine icon.
4Click the right mouse button on the machine icon and select 
Properties.
5Click the Device Settings tab, and select Installed from 
the 
Tray2 drop-down list.
6Click OK.
Downloaded From ManualsPrinter.com Manuals 
						

							E
SPECIFICATIONS
This chapter includes:
• General Specifications
• Scanner and Copier Specifications
• Printer Specifications
• Facsimile Specifications
• Paper Specifications
Downloaded From ManualsPrinter.com Manuals 
						

							SpecificationsE.2
General Specifications
ItemDescription
Automatic document 
feederUp to 50 sheets (20 lb, 75 g/m2)
ADF document size 
Width: 142 to 216 mm (5.6 to 8.5 inches)
Length: 148 to 356 mm (5.8 to 14 inches)
Paper input capacity
Paper tray (standard Tray 1 and optional Tray 2): 250 
sheets (weight: 75 g/m2, 20 lb)
Bypass tray: 50 sheets for plain paper (weight: 75 g/m
2, 
20 lb), 5 sheets for card stock, labels, transparencies, 
and envelopes
Paper output capacity
Front output tray: 150 sheets (face down)
Rear output slot: 1 sheet (face up)
Paper type
Paper tray: Plain paper (60 ~ 90 g/m2, 16 ~ 24 lb)
Bypass tray: Plain paper, Transparencies, Labels, Card, 
Post card, Envelopes (60 ~ 120 g/m
2, 16 ~ 32 lb)
Consumables
1-piece toner cartridge system
Power requirements
100 ~ 127 VAC, 50/60 Hz, 5.0 A
220 ~ 240 VAC, 50/60 Hz, 2.6 A
Power consumption
Sleep mode: 30 W
Average: 400 W
Noise
*
Standby mode: Less than 39 dBA
Printing: Less than 54 dBA
Copy: Less than 55 dBA
Warm-up time
Less than 42 seconds
Operating conditions
Temperature: 50 oF to 89 oF (10 oC to 32 oC)
Humidity: 20 % to 80 % RH
LCD
16 characters x 2 lines
Toner cartridge life
**3,500 or 5,000 pages at ISO 19752 5 % coverage (Ships 
with 3,500 pages Start Toner Cartridge)
SET dimension 
(W x D x H)
450 x 435 x 457 mm
Weight
Net: 17 Kg (including consumables)
Gross: 21 Kg (including consumables, accessories and 
package)
Downloaded From ManualsPrinter.com Manuals