Xerox Workcentre 24 Pcl 6 Manual

1–9
USER GUIDE (COPIER)
Paper Trays
Trays 1,2,3 and 4 are located at the lower front of the printer/
copier.  Tray 5 (Bypass) is located on the left side of the printer/
copier.  
Tandem Tray ModuleTrays 1and 2 are adjustable from 5.5x8.5 in. through 11x17 in. (A5 
through A3) and can accommodate up to 520 sheets based on 
paper weight.  Trays 3 and 4 are high capacity paper trays and 
can accommodate a total of 2000 sheets, 8.5x11 in. (A4 and B5) 
based on paper weight.
3-Tray ModuleTrays 1 through 4...

1–10
USER GUIDE (COPIER)
Power Saver Mode
Power Saver Mode automatically cuts off the electricity to the 
machine if it is left unused for a certain duration. The Power Saver 
feature has two modes, a Low Power mode and Sleep mode. The 
machine enters the Low Power mode after the preset time has 
elapsed if the machine is left unused for a fixed period of time.  
The machine then enters the Sleep mode if a further preset time 
elapses. 
• Low Power mode
In this mode, the power to the control panel and...

1–11
USER GUIDE (COPIER)
Quick Start Guide to Copying
This section will lead you quickly through a number of features 
and steps used in making copies. 
For more information about copy features, refer to the section 
entitled Copier Features, in this chapter.
Making Copies Using the Duplex Automatic Document Feeder
1Place original in the Original Input Area face up.  A stack of up to 
50 originals may be place in the tray.
2Slide the documents forward until the green indicator lights, 
indicating the...

1–12
USER GUIDE (COPIER)
Making Copies from the Document Glass
1Open the Document Cover.
2Place the original face down on the Document Glass, aligning the 
left rear corner with the registration guide.
3Close the cover before making a copy.
4Press the Start button.
5Remove the copies from the output tray. Remove the original 
document from the Document Glass. 

1–13
USER GUIDE (COPIER)
Making Copies Using Features
The feature tabs on the Touch Screen enable you to configure the 
printer/copier to suit your copying needs.
The procedure below leads you quickly through a number of 
features you may want to use in making copies. It assumes that 
the feature tabs are in the default configuration. 
For more information about copy features, refer to the section 
entitled Copier Features, in this chapter.
1Press Clear All to clear any previous programming
Use any of...

1–14
USER GUIDE (COPIER)
4Select an option under 2 Sided if a setting other than the default, 1 
to 1 Sided, is desired.
If another option is desired, perform one of the following:
•1 to 1 Sided for default one-sided copies.
•1 to 2 Sided for two-sided copies from one-sided input.  
•Press Head to Head for two-sided, head-to-head output, 
as for books.  
•Press Head to Toe for two-sided, head to toe output, as for 
calendars.
•2 to 2 Sided for two-sided copies from two-sided input.
You must specify the...

1–15
USER GUIDE (COPIER)
6Select an option in Paper Supply if a tray other than the default, 
Auto Paper, is desired.
If another option is desired, perform one of the following:
• Press the desired Paper Supply option on the Basic Copying 
screen.
•Press More… to see additional options.
Press the desired option and touch the Save button to return to 
the Basic Copying screen.
7On the Added Features tab, select Output to program the desired 
copy output option.
•Press Collated for collated output....

1–16
USER GUIDE (COPIER)
9If other features are desired, select the appropriate feature tab 
and feature button on the Touch Screen. 
10Perform one of the following:
• If you use the Duplex Automatic Document Feeder, place the 
document face up into the Original Input Area.  The Document 
Feeder Lamp lights when the document is in the correct 
position.  Ensure that the paper guide is against the original 
document.
• Raise the Document Cover and place the document face 
down on the Document Glass.
•...

1–17
USER GUIDE (COPIER)
Loading Paper
This section contains basic information about loading paper and 
transparencies, and about using paper trays. It also includes some 
paper usage guidelines for the WorkCentre 24.
For more information about the materials you can use, refer to the 
Recommended Materials for the WorkCentre 24.
Tray 1
Tray 1 can accommodate an assortment of standard paper sizes, 
from 5.5x8.5 through 11x17 inch, and A3 through B5. Tray 1 has 
width and length adjustment guides that can...

1–18
USER GUIDE (COPIER)
Auto Size Detect for Tray 5 (Bypass)
Certain standard paper sizes can be automatically detected in 
Tray 5 (Bypass) by selecting Auto Size Detect on the Tray 5 
programming screen. The following paper sizes can be used with 
the Auto Size Detect feature: 
• US/Canada - 5.5x8.5 in. LEF/SEF, 8x10 in. LEF, 8.5x11 in. 
LEF/SEF, 8.5x13 in. SEF, 8.5x14 in. SEF, 11x17 in. SEF.
• Europe - A5 LEF/SEF, A4 LEF/SEF, A3 SEF, B5 LEF/SEF, B4, 
Postcard (100 x 148mm).
All other paper sizes must...