Xerox Workcentre 24 Pcl 6 Manual

v
TABLE OF CONTENTS
Accessory) 89
Component Names and Functions 89
Document Specifications 90
Documents Not Recommended 91
Loading the Documents 91
Placing Documents on the Document Glass 91
Loading Documents in the DADF 92
Finisher (Optional Accessory) 93
Using the Finisher 93
Stapling Options 94
Job Status 96
Checking Current Jobs 96
Changing the Print Priority 97
Checking Completed Jobs 98
Outputting/Deleting Secure Prints 99
Outputting Sample Prints 101
Delayed Print 103
Deleting Stored Documents...

vi
TABLE OF CONTENTS 

1
1–1
1. User Guide (Copier)
Getting to Know Your Copier
Your new Xerox WorkCentre M24 works as a digital copier. This 
section will provide an introduction to the WorkCentre M24 which 
is also referred to as the WorkCentre 24.  
For more information about copy features, refer to the section 
entitled Copier Features in this chapter. 

1–2
USER GUIDE (COPIER)
123
4
10
8
9
11
7
5
6
12
13
14
15
16
17 

1–3
USER GUIDE (COPIER)
NumberNameFunction
1Duplex Automatic 
Document Feeder 
(DADF)
(Optional Accessory)Automatically feeds up to 50 documents. Also works as a 
Document Glass cover when making copies from the platen 
glass.
2Original Input AreaLocation where originals are fed onto platen glass for copying.
3Original Catch TrayOriginal return area.
4Control PanelUsed to program the copier for individual jobs.
5Center Output TrayOutput delivered here face down.
6Power SwitchPowers machine On/Off.
7Front...

1–4
USER GUIDE (COPIER)
Control Panel
The Control Panel is used to program individual jobs.  
• The Numeric Keypad is used to enter copy quantity or other 
numeric information.  
• The Contrast Dial adjusts the brightness of the touch screen.  
• The Touch Screen is where you make selections for the jobs 
you are programming. 
AccessUse this feature to change machine default settings, and to create 
or modify user access numbers.
Power SaverLights up green and is initiated automatically if the machine is...

1–5
USER GUIDE (COPIER)
InterruptStops the printer/copier during the current job.  This allows 
another job to be run. There are two indications that the job has 
been interrupted:
• The printer/copier displays a message indicating that Job 
Interrupt has been selected, and it is ready to copy.
• The indicator light flashes to acknowledge that the Interrupt 
button has been selected.  The light will continue to flash until 
the printer/copier has completed the activity in process.  The 
light will remain...

1–6
USER GUIDE (COPIER)
Job MemoryIndicator lights when data is stored in the machines memory.
OnlineIndicator lights when data is being received from a client.
FeaturesAllows you to alternate between scanning and copying feature 
screens.
Job StatusAllows you to check or cancel  jobs currently executing, or to 
check or print saved documents.
Machine StatusAllows you to check the machine status, meters, the state of 
consumables, and output reports. 

1–7
USER GUIDE (COPIER)
Touch Screen 
Press the buttons and tabs displayed in the Touch Screen to 
select features or respond to on screen instructions. The selected 
buttons are highlighted to indicate activation.  Buttons that do not 
have three-dimensional shadows are not active, and cannot be 
selected.
Message AreaMessages such as machine status and operation instructions are 
displayed here
Unused MemoryThe amount of memory remaining to store a scanned original is 
displayed prior to output....

1–8
USER GUIDE (COPIER)
Power Switch
The power switch is located on the right top corner of the machine.  
Press the switch to the ( | ) position to turn the power on. 
Ground Fault ProtectorLocated at the rear of the machine where the power cord attaches.  
The Ground Fault Protector removes all power from the machine if 
a fault is detected in the power to the printer/copier.  To reset the 
GFI, press the switch in.
Audio Tones 
Tone volume may be adjusted or turned off in System Settings 
mode. Three...