Xerox Phaser 6120 User Manual

							Loading Media 64
10After you have finished printing envelopes and before reloading paper, do 
the following:
aPull the lever, and then open the top cover.
Downloaded From ManualsPrinter.com Manuals 
						

							Loading Media 65
bLower both green fuser separator levers.
cClose the top cover.
Downloaded From ManualsPrinter.com Manuals 
						

							Loading Media 66
Loading Labels/Postcard/Thick Stock/Glossy Stock 
and
 Transparency
1Remove the lid from Tray 1, and then open the front panel of Tray 1.
2Remove any media from the tray.
3Slide the media guides to provide more space between them.
Downloaded From ManualsPrinter.com Manuals 
						

							Loading Media 67
4Load the media face up in the tray.
Up to 50 sheets can be loaded into the tray at one time.
5Slide the media guides against the edges of the media.
6Close the front panel of Tray  1, and then reattach the lid.
Downloaded From ManualsPrinter.com Manuals 
						

							Loading Media 68
Tray 2
Loading Plain Paper
1Pull out Tray 2 as far as possible.
2Lift up Tray 2 to remove it.
Downloaded From ManualsPrinter.com Manuals 
						

							Loading Media 69
3Remove the lid from Tray 2.
4Press down the media pressure plate to lock it into place.
5Load the paper face up in the tray.
Downloaded From ManualsPrinter.com Manuals 
						

							Loading Media 70
Do not load above the 100% line. Up to 500 sheets (80 g/m2 
[22
 lb.]) of plain paper can be loaded into the tray at one time.
6Reattach the lid to Tray 2.
100%
75
50
Downloaded From ManualsPrinter.com Manuals 
						

							Loading Media 71
7Reinsert Tray 2 into the printer.
Downloaded From ManualsPrinter.com Manuals 
						

							Duplexing 72
Duplexing
Select paper with high opacity for duplex (2-sided) printing. Opacity refers to 
how effectively paper blocks out what is written on the opposite side of the 
page. If the paper has low opacity (high translucency), then the printed data 
from one side of the page will show through to the other side. Check your 
application for margin information. For best results, print a small quantity to 
make sure the opacity is acceptable.
Duplex (2-sided) printing can be done manually or can be done automatically 
with the duplex unit installed and enabled.
Note:
Only plain paper, 75–90 g/m2 (20–24 lb bond) can be autoduplexed. 
See
 “Media Specifications” on page 45. Duplexing envelopes, labels, 
transparencies, or glossy is not supported.
How do I autoduplex?
You should verify that the duplex unit is physically installed on the printer and 
enabled in the printer driver to successfully duplex the job.
Check your application to determine how to set your margins for 
duplex
 printing.
The following Binding Position settings are available:
In addition, if Pages/Sheet has been set to Booklet, autoduplex printing is 
performed.
If Short Edge is selected, the pages will be laid out to flip 
at the top.
If Long Edge is selected, the pages will be laid out to flip 
at the sides.
1
3
1
21
111
12
3
Downloaded From ManualsPrinter.com Manuals 
						

							Output Tray 73
The following Order settings are available when Booklet is selected:
1Load plain paper into the tray.
2From the printer driver, specify the layout for duplex printing.
3Click OK.
With autoduplexing, the back side is printed first, and then the front 
side is printed.
Output Tray
All printed media is output to the face-down output tray on top of the printer. 
This tray has a capacity of approximately 200 sheets (A4/Letter) of 80 g/m2 
(22 lb.) paper. 
If the media is stacked too high in the output tray, your printer may 
experience paper jams, excessive media curl, or static buildup. 
Remove transparencies as soon as possible from the output tray to 
avoid static buildup.
If Left Binding is selected, the pages can be folded as a 
left-bound booklet.
If Right Binding is selected, the pages can be folded as a 
right-bound booklet.
1
12
3
3
3
1 12
Downloaded From ManualsPrinter.com Manuals