Xerox Phaser 6120 User Manual

							About the Control Panel 34
QUALITY MENU
With this menu, settings for the print quality can be specified.
All factory default values are shown in bold.
TONER 
REMOVALBLACKSettingsYES/NO
When YES is selected, the carousel rotates to the 
black toner cartridge, so that it can be replaced.
For details on replacing the toner cartridge, refer to 
“Replacing a Toner Cartridge” on page 79.
CYANSettingsYES/NO
When YES is selected, the carousel rotates to the 
cyan toner cartridge, so that it can be replaced.
For details on replacing the toner cartridge, refer to 
“Replacing a Toner Cartridge” on page 79.
MAGENTASettingsYES/NO
When YES is selected, the carousel rotates to the 
magenta toner cartridge, so that it can be replaced.
For details on replacing the toner cartridge, refer to 
“Replacing a Toner Cartridge” on page 79.
YELLOWSettingsYES/NO
When YES is selected, the carousel rotates to the 
yellow toner cartridge, so that it can be replaced.
For details on replacing the toner cartridge, refer to 
“Replacing a Toner Cartridge” on page 79.
REMOVE 
ALLSettingsYES/NO
When YES is selected, the carousel rotates to each 
toner cartridge, so that all of them can be replaced.
For details on replacing the toner cartridge, refer to 
“Replacing a Toner Cartridge” on page 79.
TONER OUT 
ACTIONSettingsSTOP/CONTINUE
When set to CONTINUE, printing continues even if the toner 
cartridge is empty.
When set to STOP, printing stops when the toner cartridge is empty.
Downloaded From ManualsPrinter.com Manuals 
						

							About the Control Panel 35
DENSITY 
CALREQUEST 
CALSettingsNO/YES
If YES is selected, image adjustments are performed.
MODESettingsON/OFF
If ON is selected, the image adjustments are applied.
If OFF is selected, image adjustments are not applied.
DENSITY 
CONTROLBLACKSettings1/2/3/4/5
Adjust the density of the black toner to one of five 
levels.
If 1 is selected, the density is at its lightest level. If 5 
is selected, the density is at its darkest level.
CYANSettings1/2/3/4/5
Adjust the density of the cyan toner to one of five 
levels.
If 1 is selected, the density is at its lightest level. If 5 
is selected, the density is at its darkest level.
MAGENTASettings1/2/3/4/5
Adjust the density of the magenta toner to one of 
five
 levels.
If 1 is selected, the density is at its lightest level. If 5 
is selected, the density is at its darkest level.
YELLOWSettings1/2/3/4/5
Adjust the density of the yellow toner to one of five 
levels.
If 1 is selected, the density is at its lightest level. If 5 
is selected, the density is at its darkest level.
TRANSFER 
BELT 
RESET 
COUNTSettings YES/NO
When YES is selected, the transfer belt counter is 
reset. Use this setting after you have installed a new 
transfer belt.
Downloaded From ManualsPrinter.com Manuals 
						

							About the Control Panel 36
CONNECTION SETUP MENU
With this menu, interface settings can be specified.
Restart the printer after changing settings in the 
NETWORK SETUP menu.
All factory default values are shown in bold.
NETWORK 
SETUPTCP/IPENABLESettingsYES/NO
If YES is selected, TCP/IP is enabled.
If NO is selected, TCP/IP is disabled.
DHCP/
BOOTPSettingsON/OFF
Select whether or not the IP address is 
automatically acquired.
If YES is selected, the IP address is 
automatically acquired.
If NO is selected, the IP address is not 
automatically acquired.
IP 
ADDRESSSetting192.168.1.2
Set the IP address for this printer on the 
network.
Use the Up, Down, Left, and Right keys 
to specify the value.
If the IP address is manually specified, 
DHCP/BOOTP is automatically set 
to
 NO.
DEFAULT 
ROUTERSetting192.168.1.2
Specify the IP address of the router if 
one is on the network. Use the Up, 
Down, Left, and Right keys to specify 
the value.
Downloaded From ManualsPrinter.com Manuals 
						

							About the Control Panel 37
SUBNET 
MASKSettings0.0.0.0
Specify the subnet mask for the 
network. Use the Up, Down, Left, and 
Right keys to specify the value.
ENABLE 
HTTPSettingsYES/NO
Specify whether or not HTTP is used.
If YES is selected, the Web page 
provided to the printer by the built-in 
HTTP server is enabled.
If NO is selected, the Web page cannot 
be used.
ENABLE 
AUTO IPSettingsYES/NO
Select whether or not the IP address is 
automatically acquired when DHCP/
BOOTP and PING, ARP are not 
functioning or when there is no 
response.
If NO is selected, the IP address is not 
automatically acquired.
If YES is selected, the IP address is 
automatically acquired.
IPX/SPXFRAME 
TYPESettingsAUTO/802.2/802.3/
ETHER II/SNAP
Specify the protocol used with 
NetWare.
ETHERTALKNAME SettingsPhaser 6120
Specify the name of the printer for 
finding printers with Macintosh 
EtherTalk.
The printer name can contain a 
maximum of 16 characters.
NAME2SettingsAutomatically 
entered
Specify the name of the printer for 
finding printers with Macintosh 
EtherTalk.
The printer name can contain a 
maximum of 16 characters.
Downloaded From ManualsPrinter.com Manuals 
						

							About the Control Panel 38
NETZONESettingsAutomatically 
entered
Specify the Macintosh EtherTalk zone.
The zone name can contain a 
maximum of 16 characters.
NETZONE2SettingsAutomatically 
entered
Specify the Macintosh EtherTalk zone.
The zone name can contain a 
maximum of 16 characters.
ETHERNET 
SPEEDSettingsAUTO/100 FULL DUPLEX/100 
HALF DUPLEX/10 FULL 
DUPLEX/10 HALF DUPLEX
Specify the transmission speed for the network and 
the transmission method for bi-directional 
transmission.
PS 
PROTOCOLSettingsBINARY/QUOTED BINARY
Select whether PostScript jobs are received in the 
binary format or the quoted format.
USB SETUPENABLESettingsYES/NO
If YES is selected, USB is enabled. 
If NO is selected, USB is disabled.
JOB 
TIMEOUTSettings0-60-999
Specify the length of time (in seconds) until the print 
job being received is timed out when USB is being 
used.
PARALLEL 
SETUPJOB 
TIMEOUTSettings0-30-999
Specify the length of time (in seconds) until the print 
job being received is timed out when Parallel is being 
used.
ACTIVE I/
FSettingsETHERNET/PARALLEL
Specify the interface to be used. 
An Ethernet and parallel connection cannot be used at the 
same
 time.
RESET 
CONN 
SETUPSettingsYES/NO
Resets all settings on the Connection Setup menu to 
factory
 defaults.
Downloaded From ManualsPrinter.com Manuals 
						

							About the Control Panel 39
SYSTEM DEFAULT MENU
With this menu, settings can be specified to adjust the operation of the printer, 
such as the time until the machine enters Energy Saver mode.
* These menu items appear only if an optional hard disk is installed. 
** This menu item appears only on 110 V units.
All factory default values are shown in bold.
PRINT 
QUALITYSettingsENHANCED/STANDARD
Select the image quality for prints.
COLOR 
MODESettingsCOLOR/GRAYSCALE
Specify whether printing is in full color or grayscale.
EMULATIO
NSDEFAULTSettingsAUTOMATIC/POSTSCRIPT/PCL5/
PCL XL/HEX DUMP/PDF
Specify the printer control language.
If AUTO is selected, the printer automatically selects 
the printer control language from the data stream.
AUTO 
DEFAULTSettingsPCL5/POSTSCRIPT
Select the printer description language when it cannot 
be identified from the data and 
DEFAULT is set to 
AUTOMATIC.
POSTSCRIP
TERROR 
PAGESettingsON/OFF
Select whether or not an error page is 
printed when a PostScript error occurs.
Downloaded From ManualsPrinter.com Manuals 
						

							About the Control Panel 40
PCLLINE 
TERMINA
TIONSettingsCR=CR LF=CRLF/ 
CR=CR LF=LF/ 
CR=CRLF LF=LF/ 
CR=CRLF LF=CRLF
Select the definitions of the CR/LF codes 
in the PCL language.
FONTPITCH 
SIZESettings44-1000-9999
Specify the bitmap font size in 
the PCL language.
FONT 
NUMBERSettings0-32767
Specify the font used with the 
PCL language.
The font numbers that appear 
correspond to the PCL font 
list. For details on printing the 
font list, refer to 
“PRINTABLE 
PAGES MENU” on page 30.
POINT 
SIZESettings400-1200- 
99975
Specify the outline font size in 
the PCL language.
SYMBOL 
SETSpecify the symbol set used 
with the PCL language.
The default setting is PC8.
STARTUP 
OPTIONSSTART 
PAGESettingsON/OFF
Select whether or not a startup page is printed when 
the printer is turned on.
If YES is selected, the startup page is printed when 
the printer is turned on.
If NO is selected, the startup page is not printed.
SYSSTARTSettingsNO/YES
Select whether or not the PostScript format definitions 
file is applied when the printer is turned on.
If YES is selected, the PostScript format definitions file 
is applied.
If NO is selected, the PostScript format definitions file 
is not applied.
Downloaded From ManualsPrinter.com Manuals 
						

							About the Control Panel 41
DATE & 
TIMESettingsyyyymmdd:hhmmss
Set the date and time on the hard disk’s time-of-day clock.
The settings appear in the following order: year, month, day:hour, 
minutes, seconds.
ENERGY 
SAVERSettings15 MINUTES/30 MINUTES/1 HOUR/2 HOURS
Specify the length of time until the machine enters Energy Saver 
mode.
This menu item appears only when ENERGY SAVER is set to ON.
2 Hours is displayed only on 110 volt units.
SECURITYCONFIGUREENABLESettingsOFF/ON
Select whether or not the menus are 
protected with a password.
If ON is selected, all menus are protected 
with a password.
SET 
PASSWOR
DSettingsSYSADMIN
Specify the password for displaying the 
menus. The specified password is 
applied only if 
SECURITY/CONFIG/
ENABLE
 is set to ON.
The password can contain a maximum of 
16 characters.
CAPTURE 
PRT JOBSettingsOFF/ON/PRINT
Select whether or not received print jobs are saved on the hard disk.
If OFF is selected, print jobs are not saved on the hard disk.
If ON is selected, received print jobs are saved on the hard disk 
without being printed.
If PRINT is selected, received print jobs are printed and saved on the 
hard disk.
Downloaded From ManualsPrinter.com Manuals 
						

							About the Control Panel 42
SERVICE MENU
With this menu, the service representative can adjust the printer and perform 
maintenance operations. This menu cannot be used by the user.
FORMATFORMAT 
FLASHSettingsNO/YES
Select whether or not to initialize the flash RAM.
If YES is selected, the flash RAM is initialized.
FORMAT 
DISKSettingsNO/YES
Select whether or not to initialize the hard disk.
If YES is selected, the hard disk is initialized.
RESTORE /
SAVERESTORE 
FACTORYSettingsNO/YES
Select whether or not all menu items are reset to their 
initial settings.
If YES is selected, all menu items are reset to their 
initial settings.
SAVE 
CUSTOMSettingsNO/YES
Select whether or not all changed menu settings are 
saved.
If YES is selected, all changes are saved.
RESTORE 
CUSTOMSettingsNO/YES
Select whether or not menu items are reverted to the 
previously saved settings.
If YES is selected, the menu items revert to the 
previously saved settings.
Downloaded From ManualsPrinter.com Manuals 
						

							About the Control Panel 43
LANGUAGE MENU
The display language of the message window can be changed to the required 
language. The available languages are:
„English
„Spa nish
„French
„German
„Italian
„Portuguese
„Dutch
„Swedish
The default setting is English.
Downloaded From ManualsPrinter.com Manuals