Xerox Phaser 6120 User Manual
Have a look at the manual Xerox Phaser 6120 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 228 Xerox manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Replacing Consumables 84 10Close the front cover. 11Carefully close the top cover. The printer must complete a calibration cycle (less than 2 minutes) after the toner cartridge has been replaced. If you open the top cover before the message READY appears, the printer stops and repeats the calibration cycle. Downloaded From ManualsPrinter.com Manuals
Replacing Routine Maintenance Items 85 Replacing Routine Maintenance Items Replacing the Imaging Unit 1Pull the lever, and then open the top cover. If there is paper in the output tray, remove it. Fold up the output tray before opening the top cover. Do not touch the transfer belt. 2Carefully pull out the imaging unit. Downloaded From ManualsPrinter.com Manuals
Replacing Routine Maintenance Items 86 Note: Dispose of the used imaging unit according to your local regulations. Do not burn the imaging unit. 3Clean the laser lens by wiping it with a soft, dry cloth. 4Prepare a new imaging unit. Do not touch the drum on the imaging unit. Downloaded From ManualsPrinter.com Manuals
Replacing Routine Maintenance Items 87 5Install the new imaging unit. 6Carefully close the top cover. The printer must complete a calibration cycle (less than 2 minutes) after the imaging unit has been replaced. If you open the top cover before the message READY appears, the printer stops and repeats the calibration cycle. Downloaded From ManualsPrinter.com Manuals
Maintaining the Printer Downloaded From ManualsPrinter.com Manuals
Cleaning the Printer 89 Cleaning the Printer CAUTION Read all caution and warning labels carefully, making sure to follow any instructions contained in them. These labels are located on the inside of the printer’s covers and the interior of the printer body. Handle the printer with care to preserve its life. If dust and paper scraps remain on the inside or outside of the printer, printer performance and print quality will suffer, so the printer should be cleaned periodically. Keep the following guidelines in mind. WARNING! Turn off the printer, unplug the power cord, and disconnect all interface cables before cleaning. Do not spill water or detergent into the printer; otherwise the printer will be damaged and an electric shock may occur. CAUTION The fuser unit is hot. When the top cover is opened, the fuser unit temperature drops gradually (one hour wait time). „Be careful when cleaning the inside of the printer or removing media misfeeds, as the fuser unit and other internal parts may be very hot. „Do not place anything on top of the printer. „Use a soft cloth to clean the printer. „Never spray cleaning solutions directly on the printer’s surface; the spray could penetrate through the air vents of the printer and damage the internal circuits. „Avoid using abrasive or corrosive solutions or solutions that contain solvents (such as alcohol and benzene) to clean the printer. „Always test any cleaning solution (such as mild detergent) on a small inconspicuous area of your printer to check the solution’s performance. „Never use sharp or rough implements, such as wire or plastic cleaning pads. „Always close the printer’s covers gently. Never subject the printer to vibration. „Do not cover the printer immediately after using it. Turn it off and wait until it cools down. Downloaded From ManualsPrinter.com Manuals
Cleaning the Printer 90 „Do not leave the printer’s covers open for any length of time, especially in well-lit places; light may damage the imaging unit. „Do not open the printer during printing. „Do not tap media stacks on the printer. „Do not lubricate or disassemble the printer. „Do not tilt the printer. „Do not touch the electrical contacts, gears, or laser devices. Doing so may damage the printer and cause the print quality to deteriorate. „Keep media in the output tray at a minimum level. If the media is stocked too high, your printer may experience media misfeeds and excessive media curl. „Keep the printer level to avoid toner spillage. „When lifting the printer, grasp the areas shown in the figure. If you have the duplex unit or Tray 2 installed, remove the option before lifting the printer. Do not lift the printer with the options. „If you get toner on your skin, wash it off with cool water and a mild soap. WARNING! If you get toner in your eyes, wash it out immediately with cool water and consult a doctor. „Make sure any parts removed during cleaning are replaced before you plug in the printer. 20.5 kg45 lb. Downloaded From ManualsPrinter.com Manuals
Cleaning the Printer 91 CAUTION Be sure to turn off the printer and unplug the power cord before cleaning. Exterior Control PanelVentilation Grill Printer Exterior Filter Downloaded From ManualsPrinter.com Manuals
Cleaning the Printer 92 Interior Cleaning the Media Feed Roller and Laser Lens 1Pull the lever, and then open the top cover. If there is paper in the output tray, remove it. Fold up the output tray before opening the top cover. Do not touch the transfer belt. 2Carefully pull out the imaging unit. Downloaded From ManualsPrinter.com Manuals
Cleaning the Printer 93 CAUTION Position the removed imaging unit as shown in the illustration at the right. Be sure to keep the imaging unit horizontal and place it where it will not become dirty. Do not leave the imaging unit removed for more than 15 minutes, and do not place the removed imaging unit in a location where it would be exposed to direct light (such as sunlight). 3Clean the media feed rollers by wiping it with a soft, dry cloth. Downloaded From ManualsPrinter.com Manuals