Xerox Documate 3115 Scanner Docking Station User Guide

							Xerox® DocuMate® 3115
User’s Guide31
Attach the Scanner Body to the Docking Station
1. Place the front of the scanner body in the front of the Docking Station.
2. Tilt the scanner body into the Docking Station and press on the back of the scanner to lock it into 
the Docking Station. 
						

							Xerox® DocuMate® 3115
User’s Guide 32 
						

							Xerox® DocuMate® 3115
User’s Guide33
4Installation
This chapter includes:
•Before You Begin on page 34
•Install the Software and Connect the Scanner on page 35
•Installing Additional Applications on page 41
•View the User Guides on page 43
•Register Your Scanner on page 44 
						

							Xerox® DocuMate® 3115
User’s Guide 34
Before You Begin
Please make sure of the following before you begin installation:
• The information in this guide may cover software not provided with the scanner you purchased. 
Please disregard any information about the software not applicable to your scanner.
• If your computer has AntiVirus or AntiSpyware software running, you may encounter alerts or 
messages during installation asking you to allow the installation to proceed. Although the 
messages will differ based on the software your computer is running, in each case you should 
allow the installation to proceed if that option is available. Alternatively, you can turn off the 
AntiVirus or AntiSpyware software before installing your scanner, but if you do, make sure to turn 
it back on again when installation is finished.
• If you already have a scanner connected to your computer, it is recommended that you remove 
that scanner’s driver program prior to installing your Xerox scanner. You can remove these 
programs from the Windows Control Panel. Please refer to the user manual provided with your 
other scanner hardware for instructions about removing the driver and software for that unit.
• If your computer is running Windows Vista or later, you may see the Windows User Account 
Control screen asking you to confirm system changes. Click the Yes button to allow the installation 
to proceed. 
						

							Xerox® DocuMate® 3115
User’s Guide35
Install the Software and Connect the Scanner
1. Start Microsoft Windows and make sure that no other applications are running.
2. Insert the installation disc into your computer’s DVD-ROM drive.
The disc automatically starts.
3. The Select Language window opens. Click the drop-down menu arrow and select the language to 
use. Click 
OK.
The disc’s Main menu window opens.
Note: If the disc does not start, check the following:
• Make sure the disc drive’s door is completely shut.
• Make sure the disc was inserted in the drive in the proper direction (label side up).
To launch the disc manually:
• Open the Windows options for your computer’s disc drives.
• Double-click the icon for your DVD-ROM drive. 
• The Installation menu for the disc should now open.
If the menu does not open:
• From the list of files on the disc, double-click the file named setup.exe. 
						

							Xerox® DocuMate® 3115
User’s Guide 36
4. On the Main menu, select Install software.
5. Make sure the boxes for 
Scanner Driver and Visioneer OneTouch are selected, as well as any other 
applications you want to install.
6. Click Install now.
Installing the Scanner Driver
The scanner driver installation will start first.
Note: The software provided with your scanner may differ slightly from the list shown in the 
window. 
						

							Xerox® DocuMate® 3115
User’s Guide37
1. The Welcome screen for the scanner driver Setup Wizard opens. Click Next.
2. On the Xerox License Agreement window, read the license agreement. If you accept the terms, 
select 
I Agree then click Next. 
If you choose not to accept the license agreement, click 
Cancel. Click Close on the Installation 
Interrupted window.
3. The software will now be installed.
4.
Stop when you see the “Complete the installation by connecting your hardware” window. Do not 
click 
OK yet. Leave the window open and proceed to the next section.
NOTE: If you do not see this on-screen diagram for connecting the scanner, stop and follow the 
instructions below. 
						

							Xerox® DocuMate® 3115
User’s Guide 38
Connect the USB Cable and Turn on the Power
1. Remove any tape from the USB cable.
2. Plug the USB cable into the USB port on the scanner then into a USB port on the computer. Check 
your computer’s manual for USB port locations.
If the plug does not attach easily, make sure that you are plugging it in correctly. Do not force the 
plug into either connection.
3. Turn on the scanner power.
The status light comes on and flashes indicating that the scanner is receiving power.
Your computer recognizes that a scanner has been plugged into the USB port and automatically 
loads the appropriate software to run the scanner.  
						

							Xerox® DocuMate® 3115
User’s Guide39
4. When you’re certain that the software has completely loaded, return to the “Complete the 
installation by connecting your hardware” window. 
5. Click 
OK to complete the installation process.
6. Click 
Close on the Installation Complete window to close and exit the driver installer. 
Installing Visioneer OneTouch
The Visioneer OneTouch software installation will start automatically after you click Close on the driver 
Installation Complete window.  
						

							Xerox® DocuMate® 3115
User’s Guide 40
1. Click Next on the Welcome to the OneTouch Setup Wizard.
2. On the Visioneer License Agreement window, read the license agreement. If you accept the terms, 
select 
I Agree then click Next.
If you choose not to accept the license agreement, the installation will terminate and OneTouch 
will not be installed.
3. Click 
Close on the Installation Complete window to close and exit the software installer.
NOTE: If you selected other software to install from the DVD the installation for that software will 
automatically start after you click 
Close on the Installation Complete window. Follow the instructions 
on-screen to install each application you selected.