Vodavi Infinite Dvx Iii Hybrid Key Telephone System Installation Manual

inflnitem DVX I’
Digital Key Telephone SystemLEAST COST ROUTING (LCR) PROGRAMMING
SECTION 765LEAST COST ROUTING (LCR) 
PROGWMING
765.1INTRODUCTION
Least Cost Routing (LCR) selects the most eco-
nomical programmed route for an outgoing call.
When a station user dials an outside number,
the LCR feature analyzes the number and then
automatically chooses an outside line from the
group that has been programmed as most eco-
nomical. The LCR feature puts the responsibil-ity of choosing the least expensive route...

injinitem DVX I’LEAST COST ROUTING (LCR) PROGRAMMINGDigital Key Telephone System
time period route within the specified route
table. Each of the 16 Route Tables contain four
time sensitive routes. Routes are determined by
the time of day and day of week as specified inthe Daily Start Time table and the Weekly
Schedule table.After the appropriate route is selected, LCR
Class of Service becomes applicable. A stationcan use only those line groups programmed
with a priority number equal to or higher than
the...

infinite”^ DVX I’
Digital Key Telephone System
LEAST COST ROUTING (LCR) PROG-GROUTE ASSIGNED
FROM EXCEPTION SEARCH EXCEPTION
FOUND
TABLE FOR MATCH
NOT
FOUND
SYSTEMCLOCK SEARCH
3-DIGIT
TABLE FOR
MATCHCOMPARE # DIALED
WITH STATION’S
DIALING PRIVILEGES NOROUTE ASSIGNED
w FROM 3-DIGITTABLE
LYES
NOT
%%I%:FOUND
TABLE FOR
MATCHI----LIST SELECTED FOR
ROUTE FROM DAILY
START TIME ANDWEEK+;LYfHlDULECO LINE SELECTED
FROM FIRST
AVAILABLE TRUNK
GROUP IN LIST OF
ALL LINESROUTE ASSIGNED
IBUSY
INSERT/DELETE
TABLE IS USED...

in.nitem DVX I’LEAST COST ROUTING (LCR) PROGRAMMINGDigital Key Telephone System
LCR PROGRAMMTNG (Cont’d)
765.2LCR TABLES PROGRAMMING
Programming StepsIf the system is in the programming mode,
continue using the program codes. If starting toprogram here, enter the programming mode.
Refer to Sec. 700.2, Program Mode Entry (Key
Station).
To program the system for Least Cost Routing:
1.Press FLASH and dial [75]. The following
message is shown on the display phone:
2.There are eight tables which can be pro-...

infhite” DVX I’Digital Key Telephone System
LEAST COST ROUTING (LCR) PROGRAMMING
LCR PROGRAMMING (Cont’d)
A.
3-Digit Area/Office Code Table
Programming Steps
1.Press 3-DIGITTABLE flexible button (But-ton # 1). The following message will be
shown on the display phone:
Where:
- L = [O] for non leading l(“1” not dialed)
[ 11 for leading 1 (“ 1” is dialed)
- NNN = area/office code
- RR = route list number 00-15
- Y = [O] do not go to 6-Digit table
[ 11 go to B-Digit table
-PP = number of digits expected to...

injinitem DVX I’LEAST COST ROUTING (LCR) PROGRAMMINGDigital Key Telephone System
LCR PROGRAMMING 
(Co&d)B.
s-Digit Office Code Table
Programming Steps
1.Press the 6-DIGIT TABLE flexible button
(Button 
# 2). The following message is
shown on the display phone:
y
Where:
- S = [O] to remove codes
[ 11 to add codes
- AAA = area code
- RR = route number 00- 15
- NNN = office code
2.Press the HOLD button to save the entry.
Confirmation tone is heard and the dis-
play will now update.
3. Enter additional...

infxnitem DVX I’Digital Key Telephone System
LEAST COST ROUTING (LCR) PROGRAMMING
LCR PROGRAMMING 
(Co&d)C. Exception Code Table
Programming Steps1. Press EXCEPTION TABLES flexible 
but-ton (Button 
#3). The following message
will be shown on the display phone:
DescriptionException Table. This table is used for 
opera-
tor calls and any other calls which would use a
one-digit or two-digit entry, rather than a 
three-
-digit area code.
Where:
- S = [O] to remove code from table,
[l] to add code to table
-...

infiniteTM DVX I’
mmLCR 
PROGRAMMING (Cont’d)
D. Route List Table
Programming Steps
1.Press the ROUTE LISTTABLE flexible but-ton (Button 
#4). The following message
will be shown on the display phone:
Where :
-RR = Route List Table number 00- 15
- T = Time Period Route list l-4
- G = CO Line Group l-7
- DD = Insert/Delete Table reference OO-
19 (## for none)
- L= LCR Class of Service (LCOS)
2.Press the HOLD button to save the entry.Confirmation tone is heard and the dis-
play will now update.
3.To enter...

injiniteTM DVX I’Digital Key Telephone System
LEAST COST ROUTING 
&CR) PROGRAMMING
LCR PROGRAMMING (Cont’d)
Route List Table (Cont’d)
Programming Steps
DescriptionLCR COS Priority. A station should be as-
signed a class of service for LCR. Refer to Sec.730.1, Station Attributes Programming, LCR
Class of service (COS). The 
LCR COS can be
between 0 and 6, with 0 being unrestricted and6 being the most restrictive. Within the time
period route List Table, line groups are given an
LCR COS priority assignment...

@initem DVX I’
LEAST COST ROUTING 
&CR) PROGRAMMING
Digital Key Telephone System
LCR PROGRAMMING (Cont’d)E. Insert/Delete Table
Programming Steps1. Press INSERT/DELETE TABLE flexible
button (button #5). The following messagewill be shown on the display phone:
Enter the table information as follows;
Where:
- TT = Insert/Delete Table Number 00- 19
- X = [O] Pi-e-Delete numbers (first digits
dialed in the number),
[l] Pre-Insert numbers (insert digits in
front of number dialed,
[2] Post-Insert numbers...