ViewSonic Pjl6243 Projector User Manual

							35ViewSonic PJL6243
35
Computer Input
Select Digital	zoom	+. The On-Screen Menu disappears and D.	zoom	+ appears. Press the SELECT button to expand the image size. Use the Point ▲▼◄► buttons to pan the image. The Panning function can work only when the image is larger than the screen size. A projected image can be also expanded by pressing the D.ZOOM ▲ or the SELECT button on the remote control. 
To exit the Digital zoom +/– mode, press any button except the D.ZOOM ▲▼ buttons, SELECT and Point buttons.
Digital	zoom	+
Select Digital	zoom	–. The On-Screen Menu disappears and D.	zoom	– appears. Press the SELECT button to compress image size. The projected image can be also compressed by pressing the D.ZOOM ▼ or the SELECT button on the remote control.  
Digital	zoom	–
To return to the previous screen size, select a screen size from the Screen Size Adjustment Menu or select an input source from the Input Source Selection Menu (see page 27) again, or adjust the screen size with the D.ZOOM ▲▼ buttons.
Note: •  The  minimum  compression  ratio  is  limited depending on the input signal, when the Keystone function is working or when the custom is selected for the screen size.  • True and Digital	 zoom	+/– are disabled and cannot be displayed when 480i, 576i, 480p, 576p, 720p,1035i or 1080i is selected in the PC System Menu (p.28). • Digital	 zoom	+/- cannot be selected when True is selected. •  The  minimum  compression  ratio  is  limited at Normal screen size.
Remote Control 
D.ZOOM	+	button
POINT	 ▲▼◄►	 buttons
SELECT	button
D.ZOOM	-	button
When this function is set to On, the picture will be top/bottom and left/right reversed. This function is used toproject the image from a ceiling-mounted projector.
Ceiling
When this function is set to On, the picture will be left/right reversed. This function is used to project the image from rear of the screen.
Rear
To reset the adjusted data, select Reset and press theSELECT button. A confirmation box appears and then select Yes. All adjustments will return to their previous figures.
Reset
Keystone
This function is used to adjust keystone distortion of the  projected image. Use the Point ▲▼ buttons to choose the item you want to adjust. Keystone    
To correct keystone distortion, press the SELECT button.  Keystone appears on the screen. Use the Point ▲▼ buttons to correct keystone distortion (p.23). Store or Reset    
To store or reset the keystone correction, press the Point ► button.    Store ............. 
Keep the keystone correction even when the AC power cord is unplugged.    Reset ............. 
Release the keystone correction when the AC  power cord is unplugged.
Keystone
Ceiling
Rear   
						

							36ViewSonic PJL6243
36
Video Input
Choose Video or S-video by pressing the VIDEO or the S-VIDEO button on the remote control.Before using these buttons, correct input source should be selected through menu operation as described below.
1
2
Video
Input	Source	Selection	(Video,	S-video)
Direct Operation
When video input signal is connected to the VIDEO jack, select Video.Video
When the input source is coming from video equipment connected to the COMPUTER IN 1/S-VIDEO IN/COMPONENT IN terminal with a S-video-VGA cable, select S-video.
S-video
Note: When the Input Search function is set to On 1   or On 2 in the Auto setup function, the input   signal will be searched automatically (p.45).
Remote Control
VIDEO button
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Input and then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select Video and then press the SELECT button.
S-VIDEO button
Video
S-video
Use the Point ▲▼ buttons to select Computer 1. And then press the Point ► button to access the submenu items. Use the Point ▲▼ buttons to select the S-video and then press the SELECT button.
Computer 1
Menu Operation
S-video
Press the Point ▲▼ buttons to select S-video.   
						

							37ViewSonic PJL6243
37
Video Input
Choose Computer	1(Component) or Computer	1(Scart)	by pressing the COMPONENT or the COMPUTER 1 button on the remote control.Before using these buttons, correct input source should be selected thro\
ugh Menu operation as described below.
1
Input Menu
2Use the Point ▲▼ buttons to select Computer 1 and then press the Point ► button.
Input	Source	Selection	(Component,	RGB	Scart	21-pin)
When the input source is coming from video equipment connected to the COMPUTER IN 1/S-VIDEO IN/COMPONENT IN terminal with a Component-VGA Cable, select Component. 
Component
When the input source is coming from video equipment connected to the COMPUTER IN 1/S-VIDEO IN/COMPONENT IN terminal with a Scart-VGA Cable, select RGB	(Scart). 
RGB	(Scart)
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Input and then press the Point ► or the SELECT button.
Note:    When the Input Search function is set to On 1     or On 2, the input signal will be searched automatically (p.45).
COMPUTER	1	button
Remote Control
3Use the Point ▲▼ buttons to select Component or RGB(Scart) and then press the SELECT button.
Computer	1(RGB)
Computer	1(Scart)
COMPONENT	button
Computer	1(Component)
Direct Operation
Menu Operation
Press the Point ▲▼ buttons to select Component or RGB(Scart).   
						

							38ViewSonic PJL6243
38
Video System Selection
1AV	System	Menu	(Video	or	S-video)
AV	System	Menu	(Component)
2
If the projector cannot reproduce proper video image, select a specific broadcast signal format from among PA L, SECAM, NTSC, NTSC	4.43, PAL-M and PAL-N.
PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N
The projector automatically detects an incoming video signal, and adjusts itself to optimize its performance.
If the projector cannot reproduce proper video image, select a specific component video signal format from among 480i, 576i, 480p, 576p, 720p, 1035i and 1080i.
Auto
COMPONENT	VIDEO	SIGNAL	FORMAT
Video or S-video
Component
The projector automatically detects an incoming video system, and adjusts itself to optimize its performance.When Video System is PAL-M or PAL-N, select the system manually.
Auto
Note: The AV System Menu cannot be selected    when selecting RGB	(Scart).
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Input and then press the Point ► or the SELECT button. 
Select Video, Computer	1(S-video) or Computer 1(Component) input source. (See pages 36-37) 
3Use the Point ▲▼ buttons to select System and then press the Point ► or the SELECT button. Use the Point ▲▼ buttons to select the desired system and then press the SELECT button.
Video Input   
						

							39ViewSonic PJL6243
39
Video Input
Image select Menu
IMAGE button
Dynamic
Real
Image 1
Image 2
Image 3
Image Mode Selection 
Image 4
Blackboard (Green)
Standard
Remote Control
IMAGE button
Select the desired image mode among Dynamic, Standard, Real, Cinema, Blackboard	(Green), Colorboard, Image 1, Image 2, Image 3 and Image 4 by pressing the IMAGE button on the remote control.
Standard
Picture mode with improved halftone for graphics.
Real
Blackboard	(Green)
Image	1–4
For the image projected on a blackboard.This mode helps enhance the image projected on a blackboard. This is mainly effective on a green colored board, not truly effective on a black colored board.
Dynamic
Direct Operation
For viewing pictures in a bright room.
Normal picture mode preset on the projector.
For viewing with the user preset image mode in the Image Adjust Menu (see page 41). 
1
2
Menu Operation
Colorboard
Colorboard
At the time of simple projection on the colored wall, you can get the close color image to the color image projected on a white screen by selecting the similar color to the wall color from the preset four colors.
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Image select and then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select  the desired item and then press the SELECT button.
Picture mode adjusted with fine tone.
Cinema
Cinema   
						

							40ViewSonic PJL6243
40
Image Adjustment
1
2
Press the Point ◄ button to decrease the contrast; press the Point ► button to increase the contrast (from 0 to 63).
Press the Point ◄ button to decrease the brightness; press  the Point ► button to increase the brightness (from 0 to 63).
Contrast
Brightness
Press the Point ◄ button to lighten R/G/B tone; press thePoint ► button to deepen R/G/B tone (from 0 to 63).
White	balance	(Red	/	Green	/	Blue)
Use the Point ◄► buttons to select the desired Color temp. level (XLow, Low, Mid or High). 
Color temp .
Press the Point ◄ button decrease the intensity of the color; press the Point ► button increase the intensity of the color (from 0 to 63).
Press the Point ◄► buttons to adjust the tint value to get a proper color balance (from 0 to 63).
Color
Tint
Note: • When the White balance Red, Green or Blue is adjusted, the Color temp. level will change to User. • Tint cannot be selected when the video system is PA L, SECAM, PAL-M or PAL-N (p. 38). • When Blackboard	(Green) or Colorboard is selected in Image select, Color temp . will change to        Blackboard or Colorboard.
Image Adjust MenuPress the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Image adjust and then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons select the desired item and then press the SELECT button to display the adjustment dialog box. Use the Point ◄► buttons to adjust the setting value.
Selected Image mode
Use the Point ◄► buttons to adjust the setting value.
Video Input
Press the Point ◄► buttons to select Off or On.Off ...... Disabled.On ...... The iris function is activated.
Iris
Press the Point ◄ button to decrease the sharpness of the image; press the Point ► button to increase the sharpness of the image (from 0 to 15).
Sharpness
Use the Point ◄► buttons to adjust the gamma value to obtain a better balance of contrast (from 0 to 15).
Gamma   
						

							41ViewSonic PJL6243
41
An interlaced video signal can be displayed in progressive mode. Select one of the following options. Off ......... Disabled. L 1 ......... For an active picture. L 2 ......... For a still picture. Film ....... For watching a film. With this function, the projector reproduces pictures faithful to the original film quality.
Progressive
Noise reduction
Noise interference on the screen can be reduced. Select one of the following options to get smoother images. Off ......... Disabled.  L 1 ......... Lower reduction  L 2 ......... Higher reduction
Note:  Noise reduction and Progressive can not be selected when the input signal is 480p, 576p, 720p, 		1035i	or 1080i (p.38). 
To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select Ye s. All adjustments will return to their previous figures. 
Reset
Store
To store the adjusted data, select Store and press the Point ► or the SELECT button. Use the Point ▲▼ buttons to select one from Image 1 to 4 and press the SELECT button. A confirmation box appears and then select Ye s. Stored data can be called up by selecting an Image (1–4) in the Image Mode Selection on page 39.
Store Menu
A confirmation box appears and then select Ye s.
Video Input   
						

							42ViewSonic PJL6243
42
This projector has the picture screen resize function, which enables you to customize the image size.
Normal
Screen	Size	Adjustment
Screen Menu1
2
Provide the image to fit the screen size while maintaining the aspect ratio of the input signal.
Custom adj .
Note: • When no signal is detected, Normal is set automatically and the Aspect adjustment menu disappears. • The adjustable range for Scale	H/V and Position	H/V is limited depending on the input signal.
Full
Provide the full screen image.
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Screen and then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons select the desired item and then press the SELECT button.
Adjust the screen scale and position manually with this function.Press the Point ► button at Custom adj . and the Custom adjustment menu is displayed on the screen, you can use the Point ▲▼ buttons to choose the item you want to adjust. Scale	H/V .......... Adjust the Horizontal/Vertical screen scale. H&V ................... When set to On, the aspect ratio is fixed. The Scale V appears dimmed and becomes unavailable. Adjust Scale H, then the screen scale is automatically modified based on the aspect ratio.  Position	 H/V ..... Adjust the Horizontal/Vertical screen position. Common ........... Save the adjusted scale or position to all the inputs. Press the SELECT button at Common to display a confirmation box. To save the scale or position, press the SELECT button at Ye s. When Custom is selected, the saved scale or position is used. Reset ................. Reset the all adjusted values. Press the SELECT button at Reset to display a confirmation box. To reset, press the SELECT button at Ye s.
CustomProvide the last stored aspect screen image. 
Video Input
Wide	(16:9)Provide the image at the 16:9 wide screen ratio.
Zoom
Pan the horizontal direction of the image and cut the vertical direction of the image to fit the screen size (16:9). Only for 4:3 video aspect ratio signals.   
						

							43ViewSonic PJL6243
43
Keystone
This function is used to adjust keystone distortion of the  projected image. Use the Point ▲▼ buttons to choose the item you want to adjust. Keystone    
To correct keystone distortion, press the SELECT button.  Keystone appears on the screen. Use the Point ▲▼ buttons to correct keystone distortion (p. 23). Store or Reset    
To store or reset the keystone correction, press the Point ► button.    Store ............. 
Keep the keystone correction even when the AC power cord is unplugged.    Reset ............. 
Release the keystone correction when the AC power cord is unplugged.
Keystone
Ceiling
Rear
When this function is set to On, the picture will be top/bottom and left/right reversed. This function is used toproject the image from a ceiling-mounted projector.
Ceiling
When this function is set to On, the picture will be left/right reversed. This function is used to project the image from rear of the screen.
Rear
To reset the adjusted data, select Reset and press theSELECT button. A confirmation box appears and then select Yes. All adjustments will return to their previous figures.
Reset
Video Input   
						

							44ViewSonic PJL6243
44
SettingSetting
Setting
Setting MenuPress the MENU button to display the On-Screen Menu. Press the Point ▲▼ buttons to select Setting and press the Point ► or the SELECT button to access the submenu items.
1
2Use the Point ▲▼ buttons to select the desired item and then press the Point ► or the SELECT button to access the selected item.
This projector has a Setting menu that allows you to set up the other va\
rious functions described below.
Language
Menu position
This function is used to change the position of the On-Screen Menu. Select Menu position and press the SELECT button.  
The Menu position changes each time you press SELECT button as follows.the center → the bottom left → the bottom right → the top left → the top right→.....
3Use the Point ▲▼ buttons select the desired item and then press the SELECT button.
Language
The language used in the On-Screen Menu is available in English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish, Finnish, Polish, Hungarian, Romanian, Russian, Turkish, Kazakh, Vietnamese, Chinese, Korean, Japanese and Thai.