ViewSonic Pjl6243 Projector User Manual

							25ViewSonic PJL6243
25
Basic Operation
Remote Control Operation
Using the remote control for some frequently used operations is advisabl\
e. Just pressing one of the buttons enables you to make the desired operation quickly without calling up the On-Screen Menu.
Press the COMPUTER 1/2, VIDEO, S-VIDEO and COMPONENT buttons on the remote control to select the input source. See pages 27, 36-37 for details.
COMPUTER	1/2,	VIDEO,	S-VIDEO	and	COMPONENT		buttons
FREEZE	button
Display the input source information: Input, H-sync freq ., V-sync freq ., Screen, Language, Lamp status, Lamp counter, Power management, Key	lock, PIN code lock and Remote control (p.57).
INFO . button
Press the D.ZOOM buttons on the remote control to enter to the Digital zoom +/– mode. See page 35 for details.
D.ZOOM	buttons
Remote Control
Note: See the next page for the description of other    buttons.
LAMP button
COMPUTER	1/2buttons
High .............. Brighter than the Normal mode. Normal .......... Normal brightness  Eco ............... Lower brightness reduces the lamp power consumption and extends the lamp life.
Press the LAMP button on the remote control to select the lamp mode for changing the brightness on the screen.
Press the FREEZE button on the remote control to freeze the picture on the screen, meanwhile, volume is muted. To cancel the Freeze function, press the FREEZE button again or press any other button.Fig.1 will appear on the screen while the Freeze function is working.
Fig.1
FREEZE	button  
D.ZOOM	buttons
VIDEO button
LAMP  button
INFO . button
S-VIDEO button
COMPONENTbutton   
						

							26ViewSonic PJL6243
26
Basic Operation
NO SHOW button
Press the P-TIMER button on the remote control to operate the Count up/Count down function. Refer to p.50 for detail of Setting for the P-timer function.To stop the count time, press the P-TIMER button.To cancel the P-timer function, press and hold the P-TIMER button.
P-TIMER	button
Press the IMAGE button on the remote control to select a desired image mode of the screen. See pages 32, 39 for details.
IMAGE buttonNo show disappears after 4 seconds.
Note:  See the previous page for the description of   other buttons.
Select the screen size (See pages 34-35, 42-43 for details).
SCREEN button
black out→ the captured image → normal →• • • • •
Press the NO SHOW button on the remote control to black out the image. To restore to normal, press the NO SHOW button again or press any other button. When the projected image is captured and is set as User in the Logo selection (p. 46), the screen changes each time you press the NO SHOW button as follows.
Note:     When use the MUTE button to release the       No Show function, the mute function can not     be operated at the same time.
IMAGE button
NO SHOW button P-TIMER	button
SCREEN button
Remote Control
No Show
P-Timer   
						

							27ViewSonic PJL6243
27
Choose either Computer	1(RGB)	or Computer	2(RGB) by pressing the COMPUTER 1 or COMPUTER 2 button on the remote control.Before using these buttons, correct input source should be selected thro\
ugh Menu operation as described below.
1
Input Menu
2
3
Note: When the Input Search function is set to On 1   or On 2 in the Auto setup function, the input   signal will be searched automatically (p.45).
Computer 1
Remote Control
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Input and then press the Point ► or the SELECT button. 
Use the Point ▲▼ buttons to select Computer 1. 
When Computer 1 is selected, press the Point ► button to access the submenu items. Use the Point ▲▼ buttons to select the RGB input source and then press the SELECT button.
COMPUTER	1	button
Computer	1(RGB)
Computer	1(Scart)
Input	Source	Selection	(RGB:	Computer	1/Computer	2)
Computer	2	(RGB)
COMPUTER	2	button
Direct Operation
Menu Operation
Computer Input 
ORUse the Point ▲▼ buttons to select Computer 2 and then press the SELECT button.   
						

							28ViewSonic PJL6243
28
Computer Input
PC System Menu
PC System Menu
Computer System Selection
This projector automatically tunes to various types of computers with its Multi-scan system and Auto PC Adjustment. If a computer is selected as a signal source, this projector automatically \
detects the signal format and tunes to project a proper image without any additional settings. (Signal formats provided in this projector are shown on page 69.)
One of the following messages may appear when:
When the projector cannot recognize the connected signal conforming to the provided PC systems, Auto is displayed on the System Menu box and the Auto PC Adjustment function works to display proper images. If the image is not projected properly, a manual adjustment is required (pp. 30-31).
There is no signal input from the computer. Check the connection between your computer and the projector. (See “Troubleshooting” on p. 63.)
Auto
-----
The preset system is manually adjusted in the PC adjust Menu. The adjusted data can be stored in Mode	1–10 (pp. 30-31).
Mode 1
PC Systems provided in this projector is chosen.  The projector chooses a proper system provided in the projector and displays it.  
SVGA 1
*Mode 1 and SVGA 1 are examples.  
1
2
PC system can also be selected manually.
Selecting Computer System Manually
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Input and then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select System and then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired system and then press the SELECT button.3
Selected system in the PC System Menu is displayed.
Systems in this dialog box can be selected.
Customized Mode (1–10) set in the PC adjust Menu (pp. 30-31).   
						

							29ViewSonic PJL6243
29
Computer Input
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total	dots, Horizontal and Vertical positions to conform to your computer.
PC adjust Menu
Auto PC Adjustment
To	store	adjustment	parametersThe adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by selecting a Mode	(1–10) in the PC System Menu (see page 28). See also “Store” on page 31.
Note: • Fine sync, Total	dots, Horizontal and Vertical position of some computers cannot be fully adjusted with the Auto PC Adjustment function. When the image is not provided properly with this operation, manual adjustments are required (pp. 30-31). • The Auto PC Adjustment cannot be operated when 480i, 576i, 480p, 576p, 720p, 1035i or 1080i is selected in the PC System Menu (p. 28). 
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select PC adjust and then press the Point ► or the SELECT button.
1
2Use the Point ▲▼ buttons to select Auto PC adj . and then press the SELECT button.
Auto PC adj .
Menu Operation
Use Point ▲▼ buttons to select  Auto PC adj . and press the SELECT button.Please wait . . . appears while the Auto PC adjustment is in process.   
						

							30ViewSonic PJL6243
30
Computer Input
PC adjust Menu
Manual PC Adjustment
Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector.  Manual PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has 10 independent memory areas to store those parameters manually adjusted. It\
 allows you to recall the setting for a specific computer. 
1
2
Use the Point ◄► buttons to adjust the value, eliminating a flicker from the image displayed (from 0 to 31).
Fine sync
Use the Point ◄► buttons to adjust the number of total dots in one horizontal period to match your PC image.
Total	dots
Use the Point ◄► buttons to adjust the horizontal picture position.
Horizontal
Use the Point ◄► buttons to adjust the vertical picture position.
Vertical
Use the Point ◄► buttons to adjust the clamp level. When the image has dark bars, try this adjustment.
Clamp
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select PC adjust  and then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select  the desired item and then press the SELECT button to display the adjustment dialog box. Use the Point ◄► buttons to adjust the setting value.
Use the Point ◄► buttons to adjust the vertical area displayed by this projector.
Display area V
Use the Point ◄►  buttons  to  adjust  the  horizontal  area displayed by this projector.
Display area H
Press the SELECT button to show H-sync freq . and V-sync freq . of the connected computer.
Current mode   
						

							31ViewSonic PJL6243
31
Computer Input
Store
To store the adjusted data, select Store and then press the Point ► or the SELECT button. Move the highlight to one of the Modes 1 to 10 in which you want to store, and then press the SELECT button.
Mode free
To clear the stored data, select Mode free and then press the Point ► or the SELECT button. Move the highlight to the Mode that you want to clear and then press the SELECT button.
Note: • Display	 area	(H/V)	cannot be selected when 480i, 576i, 480p, 576p, 720p, 1035i or 1080i is selected in the PC System Menu (p.28). • When input computer signal to the projector, PC adjust will become available.
Reset
To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select Ye s. All adjustments will return to their previous figures.  
This Mode has stored parameters.
Values of Total	dots, Horizontal, Vertical, Display area H, and Display area V.
Vacant
Press SELECT button to store the data.
Press MENU button to close this dialog box.
Mode free
Store   
						

							32ViewSonic PJL6243
32
Computer Input
Image select Menu
IMAGE button
Dynamic
Real
Image 1
Image 2
Image 3
Image Mode Selection 
Image 4
Blackboard(Green)
Standard
Remote Control
IMAGE button
Select the desired image mode among Dynamic, Standard, Real, Cinema, Blackboard	(Green), Colorboard, Image 1, Image 2, Image 3 and Image 4 by pressing the IMAGE button on the remote control.
Standard
Picture mode with improved halftone for graphics.
Real
Blackboard	(Green)
Image	1–4
For the image projected on a blackboard.This mode helps enhance the image projected on a blackboard. This is mainly effective on a green colored board, not truly effective on a black colored board.
Dynamic
Direct Operation
For viewing pictures in a bright room.
Normal picture mode preset on the projector.
For viewing with the user preset image mode in the Image Adjust Menu (see page 33). 
1
2
Menu Operation
Colorboard
Colorboard
At the time of simple projection on the colored wall, you can get the close color image to the color image projected on a white screen by selecting the similar color to the wall color from the preset four colors.
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Image select and then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select  the desired item and then press the SELECT button.
Picture mode adjusted with fine tone.
Cinema
Cinema   
						

							33ViewSonic PJL6243
33
Computer Input
Image Adjust Menu
Image Adjustment
Reset
Press the MENU button to display the On-Screen Menu.  Use the Point ▲▼ buttons to select Image adjust and then press the Point ► or the SELECT button.
1
2Use the Point ▲▼ buttons select the desired item and then press the SELECT button to display the adjustment dialog box.  Use the Point ◄► buttons to adjust the setting value.
Note:• When White balance Red, Green or Blue  is    adjusted, Color temp . will change to User.• When Blackboard(Green) or Colorboard     is selected in Image select, Color temp .  will    change to Blackboard or Colorboard.
Press the Point ◄ button to decrease the contrast; press the Point ►button to increase the contrast (from 0 to 63).
Press the Point ◄ button to decrease the brightness; press  the Point ►button to increase the brightness (from 0 to 63).
Contrast
Brightness
Press the Point ◄ button to lighten R/G/B tone; press the Point ► button to deepen R/G/B tone (from 0 to 63).
White	balance	(Red	/	Green	/	Blue)
Use the Point ◄► buttons to select the desired Color temp. level (XLow, Low, Mid, or High). 
Color temp .
Use the Point ◄► buttons to adjust the gamma value to obtain a better balance of contrast (from 0 to 15).
Gamma
Press the Point ◄ button to decrease the sharpness of the image; press the Point ► button to increase the sharpness of the image (from 0 to 15).
Sharpness
To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select Ye s. All adjustments will return to their previous figures. 
Use the Point ◄► buttons to adjust the setting value.
Selected Image mode
Store
To store the adjusted data, select Store and press the Point ► or the SELECT button. Use the Point ▲▼ buttons to select one from Image 1 to 4 and press the SELECT button. A confirmation box appears and then select Ye s. Stored data can be called up by selecting an Image	(1-4) in the Image Mode Selection on page 32.
A confirmation box appears and then select Ye s.
Store
Press the Point ◄► buttons to select Off or On.Off ...... Disabled.On ...... The iris function is activated.
Iris   
						

							34ViewSonic PJL6243
34
Computer Input
This projector has the picture screen resize function, which enables you to customize the image size.
Screen Menu
Screen	Size	Adjustment
Provide the image to fit the screen size.Normal
True
Provide  the  image  in  its  original  size.  When  the  original  image  size  is  larger  or  smaller  than  the  screen  size (1024  x  768),  the  projector  enters  to  the  panning    mode  automatically.  Use  the  Point  ▲▼◄► buttons to pan the image. When adjusted, the arrows will turn red. When reached to the correction limits, the arrows will disappear.
Full Provide the full screen image. 
Note: •  This  projector  cannot  display  any  resolution higher  than  1920  x  1200.  If  your  computer’s screen resolution is higher than it, reset the resolution to the lower before connecting to the projector.  •  The  image  data  in  other  than  1024  x  768  is modified to fit the screen size in initial mode.  • True and Digital	 zoom	+/– are disabled and cannot be displayed when 480i, 576i, 480p 576p, 720p,1035i or 1080i is selected in the PC System Menu (p. 28).  • When True is selected in the Screen menu, Digital	zoom	+/- can not be selected.
1
2
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Screen and then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons select the desired item and then press the SELECT button .
CustomProvide the last stored aspect screen image. 
Wide	(16:9)
Provide the image at the 16:9 wide screen ratio.
Adjust the screen scale and position manually with this function. Press the Point ► button at Custom adj. and the Custom adjustment menu is displayed on the screen, you can use the Point ▲▼ buttons to choose the item you want to adjust. Scale	H/V .......... Adjust the Horizontal/Vertical screen scale. H&V ................... When set to On, the aspect ratio is fixed. The Scale V appears dimmed and becomes unavailable. Adjust Scale H, then the screen scale is automatically modified based on the aspect ratio.  Position	 H/V ..... Adjust the Horizontal/Vertical screen position. Common ........... Save the adjusted scale or position to all the inputs. Press the SELECT button at Common to display a confirmation box. To save the scale or position, press the SELECT button at Ye s. When Custom is selected, the saved scale or position is used. Reset ................. Reset the all adjusted values. Press the SELECT button at Reset to display a confirmation box. To reset, press the SELECT button at Ye s.
Custom adj .
Note:  •  When  no  signal  is  detected, Normal is set automatically .  •  The  adjustable  range  for Scale	 H/V and Position	 H/V is limited depending on the input signal.
Zoom
Scale the image proportionally to fit the entire screen. Either side of image may go over the screen.
Custom adj .