ViewSonic Pjl6243 Projector User Manual

							ENGLISH
ViewSonic PJL624335
35
 
System
This function is to select the system of signal 
input to the projector. The available system 
mode are listed on the pull-down menu but-
ton according to the input signal. Selec t a 
system and then click Set button.
Control
*  If the mode (Mode1 to Mode10) which is stored in the item "PC Adjustment" (* p.38) is available, they are also listed together with the above mode.
Available selection at the RGB input
Item  Description
XGA1 ........................ 
It automatically switches to the proper computer system of the input signal.  *  
The computer system modes ( VGA, SVGA, XGA. SXGA, UXGA, WXGA...) which meet the input sig-nal are listed.
Available selection at the Video/S-video/Scart input
Item  Description
AUTO ........................ 
It automatically switches to the proper color sys-tem of the input signal.  *  
The selectable color systems are PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N.
  * AUTO is fixed at the Scart input.
Available selection at the Component input
Item Description
AUTO ........................ 
It automatically switches to the proper scanning system of the input signal.  *  
The selectable scanning systems are 480i, 576i, 480p, 576p, 720p, 1035i and 1080i.   
						

							ViewSonic PJL624336
36
Chapter 4 Controlling the Projector
Sound 
This func tion is to adjust the sound of the 
projector. The values in the text box represent 
the current control value or status.
Item Description
Volume ................... 
Adjusts the sound volume from the speaker. (0 ~ 63)Mute ......................... 
Suppresses the sound. (ON, OFF)
 *  The MIC functions MIC, MIC gain, Standby MIC out cannot be selected through the network. When using the MIC functions, please set by using the On Screen Menu of the projector.   
						

							ENGLISH
ViewSonic PJL624337
37
 
Item Description
Contrast .............................. 
Adjusts picture con-trast (0~ 63)Brightness ......................... 
Adjusts picture bright-ness (0~ 63)Color ...................................... 
Adjusts picture color saturation (0~ 63)Tint ......................................... 
Adjusts picture hue (0~ 63)Iris ............................................ 
Switches iris mode. (ON, OFF)Color temp. ....................... 
Sets a color temperature mode. (High, Mid, Low, XLow, User)White balance Red, Green, Blue ..... 
Adjusts each white balance respectively. (0~ 63)
  *  When changing the value of the white balance, the color temp. indicates "User".Sharpness ................................ Adjusts  picture sharpness. (0~ 15)
Gamma .......................................... 
Adjusts brightness of darker part of the picture. (0~ 15)Noise reduction ................  Switches noise reduction mode (OFF, L1, L2)Progressive ............................  Switches progressive mode (OFF, L1, L2, Film)
Reset............................................Resets the Image adjustment to previous levels.Store ............................................ 
Stores the Image adjustment values. Select an item [Image1 - Image4] from the pull-down menu and click Store button.Load image mode ............. 
Loads the Image mode. Select an image mode from the pull-down menu and click Load button. {Dynamic, Standard, Real, Cinema, Blackboard(Green), Colorboard, Image1 - Image4}
Image  adjustment
This function is to adjust the projected picture image and save the image mode. To store 
the adjusted value, click Store button, and to load the adjusted value, click Load button.
Control   
						

							ViewSonic PJL624338
38
Chapter 4 Controlling the Projector
PC adjustment
Click PC Adj. on the main menu. This function is to adjust the signal from 
the computer connected to the projector to obtain the proper picture 
image on the screen. 
Item Description
Current mode ...... 
Displays a current mode like VGA, SVGA, XGA. SXGA, UXGA, WXGA, etc. or Mode1 - Mode10 which are the customized mode created by using the "Mode Store" function described below.
Auto PC adj.......... 
Performs automatic adjustment.
Fine sync  .............. 
Performs Fine Sync adjustment. (0 ~ 31)
Total dots .............. 
Adjust the number of total dots in the horizontal period.Clamp ......................Adjusts the phase of the clamp.Display area 
 Horizontal ..........Adjusts the image area horizontally.
 Vertical ..............Adjusts the image area vertically.Position
  Horizontal ....... 
Adjusts the horizontal position of the screen.
 Vertical ..............Adjusts the vertical position of the screen.
Reset......................... 
Resets the PC adjustments to the previous levels.
Mode Store .......... 
Stores the PC adjustment values. Select a mode no. [Mode1 - Mode10] from the pull-down menu.
Mode Free ............ 
Clear the PC adjustment values. Select a mode no.  [Mode1 - Mode10] from the pull-down menu.   
						

							ENGLISH
ViewSonic PJL624339
39
 
Setting up the projector
Click Setting on the main menu. This function is to set up the projector. 
Select the sub menu [Screen setting] or [Setting] and then set up each set-
ting.
Setting up the projector
Item Description
Screen ..................... 
Switches the screen mode. (Normal, Full, Wide(16:9), Zoom, True, Custom) There may not be available mode depending on the input mode as shown in the table below.Ceiling ..................... 
Sets the image top/bottom and left/right reversed. (ON, OFF)Rear ........................... 
Sets the image left/right reversed. (ON, OFF)Reset......................... 
Resets the Screen settings.
Input sourceScreen mode  Video Computer
Normal 4 4Full 4 4Wide(16:9) 4 4Zoom 4 4True * 4Custom 4 4
 *  The mark "4" means that the available screen mode in the selected input source system. The error message appears when selecting the disabled screen mode indi-cated with "*".
Screen setting 
This function is to adjust the screen mode of 
the projector.  The values in the text box rep-
resent the current screen status.   
						

							ViewSonic PJL624340
40
Chapter 4 Controlling the Projector
Item Description
Terminal ................. 
Sets the COMPUTER IN 2/MONITOR OUT terminal. (Computer2, Monitor out)Power management ..... 
Sets into the selected power manage-ment mode (Ready, Shutdown, OFF) if the input signal is interrupted and no control key is pressed for the specified period of time.  * The specified time can be set 1 to 30 min.Direct on ................ 
Sets the power-on mode when the AC cord is connected to the outlet. (ON, OFF)Lamp control ...... 
Selects lamp control mode. (High, Normal, Eco) Key lock .................. 
Sets the prohibition of controls either Projector or Remote control. (OFF, Projector keys, Remote control)Fan control ............. Sets the fan control speed.  OFF  Normal mode ON1 Highland mode 1 ON2 Highland mode 2Lamp Corres.Value(h) .................. 
Displays the lamp use time (Corresponding value) . Reset the time after lamp replacement. Click "Reset", a confirmation display appears, and then click "OK", the time will be reset. 
Setting 1
Setting 2
Item Description
Language .............. 
Sets the language display of projector's on-screen display menu.Auto setup ........... 
Executes the Auto PC Adj, Input Search and Auto keystone function below according to the each setting after click-ing Start button. Auto PC Adj. ..... 
Sets Auto PC Adjustment mode. (ON, OFF) Input search ..... 
Sets the auto-input signal detection mode. (ON1, ON2, OFF)  Auto keystone .... Sets Auto Keystone mode. (Auto, Manual, OFF)Background ......... 
Sets the screen background  when no signal input. (Blue, User, Black)Display .................... 
Switches on or off the on-screen menu display on the screen. (ON, OFF)Logo ......................... 
Sets on or off the logo display on the screen during the startup. (OFF, Default, User)    
						

							ENGLISH
ViewSonic PJL624341
41
 
Setting up the projector
Item Description
Filter counter ...... 
Displays the filter counter. Reset the time after filter replacement. Click "Reset", a confirmation display appears, and then click "OK", the time will be reset. Filter warning..... 
Sets the time to indicate the filter warn-ing message on the screen. (OFF, 2000H, 3000H, 4000H) Factory default ... 
Sets all of the projector control items to the factory default setting except the fol-lowing items.    
User Logo, Logo PIN code lock, PIN code lock, Lamp Corres. Value, Filter counter, PJ time  
*  
This function is effective for all the Network settings.No show    Sets the black out image temporarily. (ON, OFF)Freeze ...................... 
Sets the image to freeze mode.  (ON, OFF)Closed caption .. 
Sets the closed caption function.  Closed caption ... 
Sets the closed caption mode. (OFF, CC1, CC2, CC3, CC4) Color ..................... 
Sets the color of the contents. (Color, White) 
Setting 3   
						

							ViewSonic PJL624342
42
Chapter 4 Controlling the Projector
Information
This page is to display the basic information of the projector status. Click 
Information on the main menu.
Items Description
Input  Displays selected input and source.System Displays selected signal system.Signal  Input signal status (Yes, No)Screen Displays screen mode.Lamp status   Displays lamp status with an icon. Refer to the table on the next page.Security Displays the security (PIN code lock) status (Yes, No)PJ time(h)  
Displays the accumulated use time of the projector.Lamp Corres. Value(h)   Displays the use time (Corresponding value) of the lamp.Filter time(h)  
Displays the accumulated use time of the filter.
Click this button to update the information.
Network
Items  Description
MAC address  Displays MAC address of the projector.IP address  Displays the IP address of the projector.
Information   
						

							ENGLISH
ViewSonic PJL624343
43
 
Indication of the lamp status
Icon display/backgroundStatus
White/BlueLamp on (Normal)
White/RedLamp on (Lamp is being used over a specified use time, replace lamp immediately)
Gray/BlueLamp off (Normal)
Gray/RedLamp off (Lamp is being used over a specified use time, replace lamp immediately)
Red/Blue with XLamp failure (Lamp failure, check lamp condition)
Red/Red with XLamp failure (Lamp failure and lamp is being used over a specified use time, replace lamp immediately)
Information   
						

							ViewSonic PJL624344
44
Chapter 4 Controlling the Projector