Toshiba Voice Processing Vp100, 300s, 300 Configuration Manual

2-Z Configumtion Mawat 
mm n Answering ‘Y to Preload all Tables 
:Y 
. .  

INSTALL 2-23 
m 
m W 
D Answering “N” to Preload All Tables 
Continues with questions as shown in INST.ALL until this merge appears:  

z-24 con&watkM h4anual 
m 
Toshiba VP Syaemn Fl&eas95.3 May, lee1  

UPDATE 
.- 
- - Chapter Contents 
Section Description PEQg 
3.1 
32 U&standing UPDATE .............................................................. 3-l 
UPDATECommands.. ......................................................... ..3- 1 
Usi- UPDATE ..................................................................... 3-3 
Getting R0ady .................................................................. 3-3 
~~i~UPDA~.................-..............................................3- 3 
kiting UPDATE...

m 
INTRODUCTION ’ 
UPDATE is used to make changes to database entries created through the INSTALL pqran~ This 
chapter explains the UF’DATE program and gives speciiic jnstrutions for using the program.  

Quick Reference Guide 
l 
UPDATE Program 
Command Description 
~ Enter UPDATE @UP Use to make changes to existing ~nfiguration 
tables. 
Exits and saves information entered during session. 
If important change were mad& qstem 
confiition should also be backed up to the hard 
disk of the CM 
Enter UPDATE : . A (table name) 
whIIe in INSTALL While in the IN!Xti program, enter the UPDATE 
: . D (table name) program m add, delete, modiij or list infotition-in 
: .M (table name) a Configuration lhble. 
: . L...

UPDATE 3-l 
w 
3.1 UNDERSTANDING UPDATE 
Adds, changes, and deletions of information are mmplished l Wough the IPDATE program. 
Use of UF’DATE does not impact system operation. 
n UPDATE Commands 
The following commands are used in the WDATE program. To use the commands with each 
configuxatiort tabI& refer to the specifii table section of this chapter. 
- LIST 
Use LIST to print or display information stored in the Toshiba 
VP System database. T%is is the information you entered during 
INSTALL and the...

ADD and DELETE Use these commands to add or delete information currently stored 
in the various lbshiba VP System database tab&~ lb ADD, at the 
dot (.) prompt enter 
To DELETE, at the dot (.) prompt enter 
D (TABLE NAME) (MODIFIER)~j  

3.2 USlNG UPDATE 
Tke Option Control Ch@ (CCC) contains the features the lbshiba VP System is equiw with. 
You cannot enter the 
UFDATE program if the OCC is not installed or if the OCC is generating 
hardware errors Refer t0 the IMuRiuion u& Mainrenance manual - HARDWAR~‘Option 
Control Chip, for more iuformation. . 
B 
- ~ 
n Exiting UPDATE  Getting Ready 
Refer to the~InsM&br and Mae manual - INSTUTION for instructions on 
conne&ng the termiual. Refer to the UNDERSTANDING CONFlGURATlON chapter,...

3-4 Gmffguralion Manual 
mm If “N” is entered, only the system htz&r displays. If you have made important changw.save 
them onto your disk&E. The current information replaces the previous information. 
lf you have made important changes, it is reaxnmended that you back up the system 
amfigumtion onto the bard disk drive of your CAE Refer to the f?uim and Mainfenuce 
manual- PROCEDURES,Backuphcedures 
. : 
- . .- 
If a modiiition is made to a parameter or attribute that requires a RESTAKI’ for the 
change...