Toshiba Voice Processing Vp100, 300s, 300 Configuration Manual

UPDATE 3-5 -1. ~ 
m 
B Using UPDATE Commands 
While using UPDAX at the dot (.), type in the first letter of the command you want to w a 
spaq then the name of the table you choose. Tie mm displays information asked for, or 
displays a prompt followed by a colon c) indicating it is waiting for additional information. 
.h INFO 
If a space and a question mark (?) is typed after the command and table name, thi -em 
displays ail of the HELP prompts to guide you though the procedure. 
‘E&de 3-l is a list of...

Table 3-l UPDATE, Abbreviations, Valid Commands and Modlflers 
COMMAND 
AFJBREV 
MODIFIER 
BU.WNFORMATION 
4wA BUS 
NOT-~-W- mw 
I-PA [AmUTES] 
WAT 
C!STA 
CUSOM-PROMI’I’S 
uf cm 
PlHw +.- 
DATE M DATE 
DAYLIGHT SAVING TIME 
JJ4.A DST 
DISTRIBUTION 
WPA DIST 
t-I-Y=1 
DTMFINT 
WA DTMFINT 
FIRSTDIGXS L 
HOLIDAY 
LD?A HOL 
lNFORMATION 
WD?A INFO 
LOCATION 
uftn.4 
NAMES 
Lwn-4 NAM 
NUMBERING-PLAN 
WSA 
PORTS PORT 
PREFDC-DIGITS PRE 
PROFILZ L PROF 
ROUTE 
LMDA ROUT 
SCHEDULE 
WA 
P==fJ-JJTl 
SLOTS l 
WA...

n Using UPDATE while in the INSTALL Program 
WhileintheINSTAU program, you can enter the UPDATE progmm to add, delete, modi@ 
or list information in Confiition Bbles. 
~e~p~~~a~on~)wh~~~~~gfora~~Yon~~a 
dot (.), which is the UPDAIE mxnruand, followed by A (ADD), D (DEiLElTE), M (MODIFY) 
or L (LIST) fokived by the name of the table you w-ish to alter. The INSTALL prqqam 
puts you into the UPDAn program. when you are finished with your alteration in UPDAm 
(ty entering a -1 at the colonA you are returned...

3, 
UPDATE 
.- 
Chapter Contents 
Section DescriDtion Paw 
3.1 
3.2 Ur&&anding UPDATE .............................................................. 3-l 
UPDATECommar?ds.. ......................................................... ..3- 1 
Using UPDAE .................................................................. ...3- 3 
Galting F&&y ................................................................... 3 
Entaring UPDATE ............................................................. ...3- 3 
Exiting...

INTRODUCTION 
UFDATE is used to make changes to database entries created through the INST~ program. T&is 
chapter explains the UPDATE program and gives specifii instructions for using the program. 
.*- 
T-W.Sysmca Rekuw5.3 Ma).lESl  

Quick Reference Guide 
+*- 
UPDATE Program 
Command DescxipUon 
- - - Enter UPDATE @UP Use to make changes to existing o3nfiguration 
tables 
im ExItUPDATE .E 
* 1, Exits and saves information entered daring session. 
If important changes were made, qstem 
confiition should also be backed up to the hard 
disk of the CAT. 
Enter UPDATE : .A (table name) While in the INSTALL program, enter the UPDATE 
while In INSTALL : . D (table name) program to add, delete, modify or Iist information in - 
: . M (table...

UPDATE 3-l 
m 
3.1 UNDERSTANDING UPDATE 
Adds, changes, and deletions of information are aax)mplished *&rough the UPDATE program. 
Use of UPDATE does not impact *em operation. 
w UPDATE Commands 
l *- 
De following commands are used in the UPDATE program. Tb use the commands with each 
configuration tabI% refer to the specific table section of this chapter. 
LIST Use IJST to print or display information stored in the Toshiba 
VP System database. This is the information you entered during 
lNSTALL and the...

3-2 Gmigumionl%4anld 
ADD and DELETE usethesew 
mmands to add or deiete information currently stored 
inthevariousXxhibaVF’Systemdatabsetables TbADD,atthe 
dot (.) prompt enteE 
A (TABLE NAbfE) (MODIFIELR) -3 
To DELETE, at the dot (.) prompt enters 
l 
D (TABLE NM) (blODIFIEFt)[=]  

UFDATE 3-3 
3.2 USING UPDATE 
llte Option Control Chip (OCC) contains the features the lixhiba VP System is equippfxl with. 
You cannot enter the 
UPDATE program if the OCC is not installed or if the OCC is generating 
hardware errors Refer to tbehzshhtbn and M&me manual - 
HARDWARE, O$ion 
&ntmI Ch@ for more information. 
m 
n 
Getting Ready 
Refer tqthe khdladon and M&we manual - lNsI4UATION for instructions on 
connect& the terminal. Refer to the UNDER!XANDlNG CONFIGURATION chapter, 
hsuring Security...

3-4 Cor#iguration Man& 
w 
mm If ‘3” is entered, only the qstem header displays. If you have made important changes, save 
them onto your diskette. The current infom&on replaces the previous informatioxL 
If 
you have made important changes, it is remmended that you back up the system 
[email protected] onto the hard disk drive 
of your CKC Refer to the In@- and Maihmance 
manual 
- PROCEDURES, Backup Procedures. 
- ~ If a modification is made to a parameter or attribute that requires a REZXART for the 
change...