Toshiba Strata Xiie, Strata Xxe Electronic Key Telephone Systems Installation And Maintenance Manual

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
Any key (except INT) may be assigned a fea- NOTE: 
ture code (Figure 3). All assigned feature codes Except for Automatic Dialing m keys, 
have priority over Program 4XX assignments. a feature will be rejected if you try to 
For all keys, write in the code for the feature to enter it at another key once its code has 
be assigned on each station. been entered. Rejected assignments will 
default to m keys. 
FEATURE 
08 
CO8 
09 co9 
10 co10 
11 co11 87...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
5) Door Phone B Ring - mark an X next to 
CO1 1 if the door phone unit connected to the 
Door Phone Control Box output B is to ring at 
this EKT. Leave blank if this EKT is not to ring. 
6) Door Phone A Ring - mark an X next to 
CO10 if the door phone unit connected to the 
Door Phone Control Box output A is to ring at 
this EKT. Leave blank if this EKT is not to ring. 
7) Group Page 4 - mark an X next to CO9 if 
the station is included in Group...

10) Mark an X next to CO2 if automatic off- 
hook selection is to be INT. 
NOTE: 
In Program 01, if CO1 5 is left blank, 
items 5, 6, 7 and 8 above will default to 
Dial 9. Item 9 has priority over items 5, 6, 
7 and 8; item 10 has priority over items 5, 
6, 7, 8 and 9. 
11) Ringing Line Preference - mark an X next 
to CO1 if the station is allowed the Ringing 
Line Preference feature. 
12) Automatic Dialing Allowed - mark an X 
next to INT if the station is allowed the Auto- 
matic Dialing feature. 
6XX...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY1986 
NOTE: 
Each line can ring on only eight stations. 
If more than eight are programmed, only 
the eight stations with the lowest station 
numbers will ring. 
02.80 Initialization 
02.81 Strata has a list of standard sys- 
tem data assignments stored in ROM that can 
be entered any time by initializing the system. 
The system must be initialized when it is first 
installed or whenever the HCAU is changed. 
This allows the system to be tested and any...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 2 
INITIALIZED DATA 
SYSTEM OPTIONS 
01 Program 
System Assignments (Basic) 
Alternate Point Answer of Transferred CO Line 
= Allowed 
System Speed Dial Override of Toll Restriction 
= Not allowed 
CO Line Groups = 1 (dial 9) 
Two-CO Line Conference = Allowed 
DP Make Ratio = 40% 
MF Signal Time = 80 ms 
Privacy/Non-Privacy = Privacy 
Station 17 = 20-key EKT 
Incoming Call Abandon = 6 seconds 
Pause Timing After Flash = 1.5 seconds 
Pause...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 2 - INITIALIZED DATA (continued) 
CO LINE OPTIONS 
06 Program 
Automatic Release On Hold 
Disabled = All CO lines 
0#6 Program 
Trunk-to-Trunk Connection 
CO Tandem Switching = Disabled 
07 Program Enable 
Enable 
Automatic Release On Hold Timing 
ESS Timing = All CO lines 
08 Program 108 Program 
Toll Restriction Override Code #I 
Blank 
Tenant Service Selection 
Tenant #l = All CO lines 
0#8 Program 
Night Ring Over External Page 
No Ring...

PROGRAMMlNG PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 2 - INITIALIZED DATA (continued) 
STATION OPTIONS 
3XX Program 
Station CO Line Access 
Access Allowed = All lines, ail stations 
4XX Program 
Station Type Assignment 
20-key “A” Assigned = All stations 
CO1 Start = All stations 
4#XX Program 
Station Flexible Key Assignments 
Assignment = Basic keystrip 
5XX Program 
Station Class of Service #l 
Privacy Override = Not allowed, all stations 
DND Override = Not allowed, all stations 
Executive...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
Table Title 
Program Page 
3 
4 
5 
6 
7 
8 
9 
10 
11 
12 
13 
14 
15 
16 
17 
18 
19 
20 
21 
22 
23 
24 
25 
26 
27 
28 
29 
30 
31 
32 
33 
34 
:zi 
:z 
39 
40 
41 
42 
43 
44 
45 
46 
System Data Printout Selection Codes 
Automatic Dialing Memory Printout Selection Codes 
System Assignments (Basic) 
System Assignments (Options) 
Account Code Digit Length and TIE Line/OPX Selection 
System Assignments (Options) 
CO Outpulsing Selection...

03 SYSTEM DATA PRINTOUT 
03.00 System Data Printout Via SMDR 
03.01 If the Strata system is equipped 
with Station Message Detail Recording 
(SMDR), it is possible to obtain a printout of 
the system data and speed dialing memory via 
a printer that is connected to the SMDR output 
port (HSMB module). b) Depress the m key on station 17. 
l SPKR LED goes on. 
c) Dial Bi. 
l The SPKR LED begins to flash. 
03.02 The data should be printed during a 
low traffic period since this procedure inter- 
feres with...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 3 
SYSTEM DATA PRINTOUT SELECTION CODES 
PROGRAM NUMBER 
LED on = X LED off = 0 
TABLE 4 
AUTOMATIC DIALING MEMORY PRINTOUT SELECTION CODES 
AUTO DIAL LISTS (System & Stations 10 - 19) 
AUTO DIAL LISTS (Stations 20 - 29) AUTO DIAL LISTS (Stations 30 - 39) 
co2 0 0 0 0 x x x x 0 0 
co1 0 0 x x 0 0 x x 0 0 
INT 0 X 0 X 0 X 0 X 0 X  IINTI o I )  LED130 
131 132 133 134 135136 137 138 
1391 
CO81 X 
-2o-