Toshiba Strata Xiie, Strata Xxe Electronic Key Telephone Systems Installation And Maintenance Manual

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 9 
PROGRAM 04 
CO OUTPULSING SELECTION 
1) Lock in the SET switch on the HCAU. 
If the LED is already on, depressing the asso- 
l LED ‘ON = Dial Pulse (DP) operation ciated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
this program 
66) Go to Step 2 in a~~ther program table 
. . ~ or . . . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 MW/FL LED goes off....

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 10 
PROGRAM 05 
AUTOMATIC RECALL FROM HOLD TIMING 
(This program is used only if CO 10, CO 11 and CO 12 LEDs are ALL off in Program 5#XX.) 
1) Lock in the SET switch on the HCAU. 
3) Dial B B on the dial pad. 
Using the various keys, turn the associated 
LEDs on or off, as required. The detailed mean- 
ing of each key/LED is shown below. e on according to pres- 
itted to be on, depressing 
that LED on and turn off 
Go to Step 2 in another...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 11 
PROGRAM 0#5 
CAMP-ON TIMEOUT 
1) Lock in the SET switch on the HCAU. Station 17 MW/FL LED on. 
3) Dial w u g on the dial pad. 
4) Refer to the System Record Sheet. 
Using the various keys, turn the associated 
LEDs on or off, as required. The detailed mean- Only the LED is permitted to be on, depressing 
Paragraph 02.06. 
-33-  

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 12 
PROGRAM 06 
AUTOMATIC RELEASE ON HOLD ENABLE 
1) Lock in the SET switch on the HCAU. Station 17 MW/FL LED on. 
Using the m keys, turn the associated LEDs 
on or off, as required. Each CO key/LED 
represents itself-that is, if CO1 LED is on, CO1 eet means t 
If the LED is already on, depressing the as- 
sociated key will turn it off and vice versa. LEDs 
turned off and on until the desired pat- 
6B) Go to Step 2 in aonbther program table...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1988 
TABLE 13 
PROGRAM 0#6 
TRUNK-to-TRUNK CONNECTION ENABLE 
W/FL LED on. 
1) Lock in the SET switch on the HCALJ. 
allowed trunk-to-trunk connection. If 
k connection will If the LED is already on, depressing the as- 
sociated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
or . . . 
66) Go to Step 2 in another program table 
. . . or . _ . 
6C) Transfer data into working memory per SET LED goes off. 
NOTE:...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 14 
PROGRAM 07 
AUTOMATIC RELEASE ON HOLD TIMING 
1) Lock in the SET switch on the HCAU. 
If the LED is already on, depressing the as- 
sociated key will turn it off and vice versa. LEDs 
will have XB (crossbar) timing for AROH. 
If CO1 
is off, CO1 will have ESS (electronic) tim- 
or . . . 
6B) Go to Step 2 in inother program table 
SET LED goes off. 
into working.memory per 
MO TE: . 
This program affects only those CO lines enabled via...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 15 
PROGRAM 08 
TENANT SERVICE SELECTION 
W/FL LED on. 19 Lock in the SET switch on the HCAU. 
ystem IS In program mode. 
on programming, refer to SPKR LED flashes continuously. 
CO LEDs go on according to present data. 
ed off and on until the desired pat- 
669 Go to Step 2 in gz;h& program table 
SET LED goes off. 
MOTE: 
This program will have no meaning unless Tenant Service was selected in 
Program 03. 
-37-  

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 16 
PROGRAM 0#8 
NIGHT RING OVER EXTERNAL PAGE 
1) Lock in the SET switch on the HCAU. W/FL LED on. 
ystem IS In program mode. 
on or off, as required. Each CO key/LED 
represents itself-that is, if CO1 LED is on, 
when the system is in night operation, incom- 
ing calls over that CO line will ring over the 
rnal page; if CO1 LED is off, incoming calls 
that CO line will not ring in night opera- the LED is already on, depressing the as-...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 17 
PROGRAM 09 
SINGLE CO LINE (DIAL 9) GROUP SELECTION 
1) Lock in the SET switch on the HCAU. W/FL LED on. 
ystem 1s In program 
mode. 
on or off, as required. Each CO key/LED 
represents itself-that is, if CO1 LED is on, CO1 
will be included in the “Dial 9” group for ran- 
dom selection by a single line (OPX) extension 
or by any station using Trunk Queuing. If CO1 hOen.LED is already on, depressing the as- 
sociated key will turn it off...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 18 
PROGRAM 09X 
FOUR CO LINE (DIAL 91,92,93,94) GROUPS SELECTION 
1) Lock in the SET switch on the HCAU. 
keys, turn the associated LEDs 
required. Each CO key/LED If the LED is already on, depressing the as- 
sociated key will turn it off and vice versa. LEDs 
with this program 
or . . 1 
6B) Go to Step 2 in inother program table 
. . . or D . , 
into working memory per 
NOTE: SET LED goes off. 
Station 17 MW/FL LED goes off. 
Use this...