Toshiba Strata Xiie, Strata Xxe Electronic Key Telephone Systems Installation And Maintenance Manual

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 19 
PROGRAM 0#9 
OFF-PREMISE LINE HUNTING 
1) Lock in the SET switch on the HCAU. 
uired. Each CO key/LED represents associated key will turn it off and vice versa. 
first incoming CO line connected to LEDs may be turned off and on until the desired 
(i.e., 1,4, 7, etc.) will ring the HUNT 
output in the day and night mode if the asso- 
ciated LED is off. If the LED is on, the HUNT 
6B) Go to Step 2 in a%her program table 
into working memory...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 20 
PROGRAM 100 
TOLL RESTRICTION SYSTEM PARAMETERS 
(DIALING PLAN) 
1) Lock in the SET switch on the HCAU. 
2) Depress the m key on station 17. 
3) Dial 0 m 1 on the dial pad. 
4) Refer to the System Record Sheet. 
Turn the associated LED on for the dialing plan 
of the home Area Code. Only one LED may be 
on at one time. 
5) Depress the m key to place new data 
in memory. 
6A) Return to Step 2 in order to continue with 
this program 
6B) Go...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 21 
PROGRAM 101 
TOLL RESTRICTION DISABLE 
W/FL LED on. 
1) Lock in the SET switch on the HCAU. 
stem IS In program mode. 
If the. LED is already on, depressing the asso- 
ciated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
this program 
6B) Go to Step 2 in another program table 
-43-  

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 22 
PROGRAM 102 
FORCED ACCOUNT CODE CHECK 
1) Lock in the SET switch on the HCAU. 
associated LEDs 
l LED ON = Forced Account Codes are checked. 
l Each CO key/LED represents itself-that 
is, if the CO1 LED is on, stations calling out 
over CO1 will be forced to enter an account If the LED is already on, depressing the asso- 
ciated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
this program 
6B)...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 23 
PROGRAM 103 
OCC or EQUAL ACCESS #1 
1 SET LED on. 
1) Lock in the 
SET switch on the HCAU. Station 17 MW/FL LED on. 
is in program mode. 
X=LEDon 
All LEDs off = no data 
66) Go to Step 2 in aonb;h& program table 
. . . or . . . 
6C) Transfer data into ,working memory per 
~ Paragraph 02.06. 
I SET LED goes off. 
Station 17 MW/FL LED goes off. 
-45-  

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 24 
PROGRAM 104 
OCC AUTHORIZATION CODE LENGTH #I 
1) Lock in the SET switch on the HCAU. tation 
17 MW/FL LED on. 
As each diglt IS entere 
LEDs as shown below. 
o-digit number is 
X = LED on 
. ..or... 
6B) Go to Step 2 in another program table 
. . . or . . . 
6C) Transfer data into working memory per 
Paragraph 02.06. 
-46-  

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 25 
PROGRAM 105 
OCC or EQUAL ACCESS #2 
W/FL LED on. 
1) Lock in the SET switch on the HCAU. 
X=LEDon 
All LEDs off = no data 
with this program 
6B) Go to Step 2 in a%& program table 
. . . or . . . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 MW/FL LED goes off. 
-47-  

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 26 
PROGRAM 106 
OCC AUTHORIZATION CODE LENGTH #2 
1) Lock in the SET switch on the HCAU. W/FL LED on. 
stem IS In program mode. 
wo-digit number is 
X=LEDon 
6A) Return to Step 2 in order to continue 
with this program 
or . . ~ 
6B) Go to Step 2 in inother program table . . 0 
or . I . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 MW/FL LED goes off. 
-48-  

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 27 
PROGRAM 108 
TOLL RESTRICTION OVERRIDE CODE #I 
W/FL LED on. 
1) Lock in the SET switch on the HKSU. 
LEDs as shown below. 
X = LED on 
All LEDs off = no data 
lace new data in 
6A) Return to Step 
with this program 
or . . . 
6B) Go to Step 2 in inother program table 
. . . or . . . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 MW/FL LED goes off. 
-49-  

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 28 
PROGRAM 1 OS 
TOLL RESTRICTION OVERRIDE CODE #2 
I I 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 17 MW/FL LED on. 
System is in program mode. 
Normal functions halt on station 17. 
SPKR LED steady on. 
2) Depress the 
l 3 key on station 17. 
3) Dial 0 B m on the dial pad. SPKR LED flashes continuously. 
CO LEDs indicate present data. 
4) Refer to the System Record Sheet. This pro- As each digit is entered, the entry is...