Toshiba Strata Xiie, Strata Xxe Electronic Key Telephone Systems Installation And Maintenance Manual

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 29 
PROGRAM 1X0 
TOLL RESTRICTION CLASS PARAMETERS 
1) Lock in the SET switch on the HCAU. 
on the dial pad. 
If the LED is already on, depressing the asso- 
ing of each key/LED is shown below. ciated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
66) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. c 
Station 17 MW/FL LED goes off. 
-51-  

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 30 
PROGRAM 1 XY 
TOLL RESTRICTION CLASS AREA CODE ENTRY 
(LCD TELEPHONE REQUIRED) 
1) Lock in the SET switch on the HCAU. Station 17 MW/FL LED on. 
System is in program mode. 
Normal functions halt on station 17. 
LCD displays dialed number. 
I 1A) Go to Step 2 in another program table 
~ D ~ or . . . 
11 B) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 MW/FL LED goes off. 
New data is stored, previous...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 31 
PROGRAM 1X2 
TOLL RESTRICTION CLASS OFFICE CODE ENTRY 
(LCD TELEPHONE REQUIRED) 
1 SET LED on. 
1) Lock in the 
SET switch on the HCAU. I 
Station 17 MW/FL LED on. 
System is in program mode. 
ons halt on station 17. 
5 to enter additional area 
. . . or . . . 
116) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 MW/FL LED goes off. 
New data is stored, Drevious data is erased. 
“Skip steps 6 and 7 if...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 32 
PROGRAM 1X1 
TOLL RESTRICTION CLASS AREA/OFFICE CODE EXCEPTION TABLE SELECTION 
1) Lock in the SET switch on the HCAU. 
LEDs on or off, as required. The detailed mean- 
ing of each key/LED is shown below. If the LED is already on, depressing the asso- 
II turn it off and vice versa. LEDs 
d off and on until the desired pat- 
LEDs (except MW/FL) go off. 
. . . or . . . 
EB) Transfer data into working memory per 
Paragraph 02.06. SET LED...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1988 
TABLE 33 
PROGRAM 2XY 
TOLL RESTRICTION AREA/OFFICE CODE EXCEPTION TABLE 
(LCD TELEPHONE REQUIRED) 
1) Lock in the SET switch on the HCAU. Station 17 MW/FL LED on. 
System is in program mode. 
Normal functions halt on station 17. 
try of area code (or displays 
SPKR 
LED flashes continuously. LED displays 
. ~ . or . . . 
15B) Go to Step 2 in another program table 
. . . or . . . 
15C) Transfer data into working memory per 
Paragraph 02.06. 
“Skip...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 34 
PROGRAM 190 
PBX BACKUP 
W/FL LED on. 
1) Lock in the SET switch on the HCAU. 
em IS In program mode. 
on or off, as required. Each CO key/LED 
represents itself-that is, if CO1 LED is on, the 
system assumes that the CO1 line is connected 
to a PBX line and will cause features such as 
nd Automatic Dialing to func- e LED is already on, depressing the as- 
lace new data in 
6A) Return to Step 2 in order to continue 
with this program 
or ....

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 35 
PROGRAM 19X 
PBX ACCESS CODES 
1) Lock in the SET switch on the HCAU. 
(X = 2) to program second SPKR LED flashes continuously. 
INT, COl, C02, CO3 LEDs indicate present 
(two digits must be entered.) 
0 If the access code is a single digit, enter 1 
as the second digit. 
l If all combinations following a particular 
first digit are to be considered access codes 
(e.g.. 91,92,93, etc.) depress themkey 
(= ‘“D” on Record Sheet) for the...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 36 
PROGRAM 3XX 
STATION CO LINE ACCESS 
1) Lock in the SET switch on the HCAU. 
The various LEDs will indicate present data. 
NOTE: 
For multiple station programming, 
refer to 
rn the associated LEDs o 
0 Each CO key/LED represents itself-that is, 
if the CO 1 LED is on, then the station being 
programmed (XX) isallowed access to COl, If the LED is already on, depressing its asso- 
ciated key will turn it off and vice versa. LEDs 
may be...

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 37 
PROGRAM 4XX 
STATION TYPE ASSIGNMENT 
W/FL LED on. 
1) Lock in the SET switch on the HCAU. 
SPKR LED flashes continuously. 
The various LEDs will indicate present data. 
on programming, refer to 
If the LED is already on, depressing’ its asso- 
ciated key will turn it off and vice versa. LEDs 
. . . or . . . 
33) Go to Step 2 in another program table 
. ..or... 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off....

PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 38 
PROGRAM 4#XX 
STATION FLEXIBLE KEY ASSIGNMENTS 
(LCD TELEPHONE RECOMMENDED) 
1) Lock in the SET switch on the HCAU. Station 17 MW/FL LED on. 
SPKR LED flashes continuously. 
multiple station programming, 
refer to 
the key to be programmed. 
IMPORTANT! 
A 20-key LCD EKT is highly recommended 
features for chosen station are programmed. 
7) Depress Islini; key to place new data in 
memory. All station 17 LEDs (except MW/FL) go off. 
8A)...