Toshiba Strata E Electronic Key Telephone System Installation And Maintenance Manual

rnuunHlUllUllNb rnuLtuUntS 
SECTION 500-036-300 
JANUARY 1988 
TABLE 22 - 
PROGRAM 0#9 
OFF-PREMISES LINE HUNTING 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/l?’ LED 19 on. 
System is in program mode. 
2) Depress the m key on station 13/l 7. 
3) Dial 4 ag on the dial pad. Normal functions halt on station”i3/17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using...

TABLE 23 
PROGRAM 190 
PBX BACKUP PROGRAMMING PROCEDURES 
SECTION 500-036-300 
_ JANUARY 1988 
SET LED on. 
1) Lock in the SET switch on the HKSU. 
2) Depress the m key on station 13/l 7. 
3) Dial 011 on the dial pad. Station 13/17 LED 19 on. 
System is in program mode. .*- 
Normal functions halt on station 13/17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs indicate present data. 
4) Refer to the System Record Sheet. 
An X on the record sheet means the LED should 
Using the appropriate...

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 24 
PROGRAM 19X 
PBX ACCESS CODES 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. 
Normal functions halt on station r3/17. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
3) Dial EliI on the dial pad. X = 1 - 8 (corre- SPKR LED flashes continuously. 
sponding to the access code being program- Various LEDs indicate present data. 
med). Dial aQi(X = 1) to program first...

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
- JANUARY 1988 
TABLE 25 
PROGRAM 100 
TOLL RESTRICTION SYSTEM PARAMETERS 
(DIALING PLAN) 
SET LED on. 
1) Lock in the SET switch on the HKSU. 
2) Depress the m key on station 13/l 7. 
3) Dial 011 on the dial pad. Station 13/17 LED 19 on. 
System is in program mode. .*- 
Normal functions halt on station 13/17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
An LED indicates present data. 
4) Refer to the System Record Sheet. 
Turn the associated LED on...

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 26 
PROGRAM 101 
TOLL RESTRICTION DISABLE 
, 
1) Lock in the SET switch on the HKSU. 
2) Depress the m key on station 13/l 7. 
3) Dial iii on the dial pad. 
4) Refer to the System Record Sheet. 
Using the appropriate keys, turn their asso- 
ciated LEDs on or off, as required. Each CO 
key/LED represents itself-that is, if LED 01 
is on, toll restriction is not applied to that CO1 
line; if LED 01 is off, toll restriction is applied 
to that...

TABLE 27 PROGRAMMING PROCEDURES 
SECTION 500-036-300 
- JANUARY 1988 
PROGRAM 102 
FORCED ACCOUNT CODE CHECK 
SET LED on. 
1) Lock in the SET switch on the HKSU. 
2) Depress the m key on station 13/l 7. 
3) Dial flfl1 on the dial pad. Station 13/l 7 LED 19 on. 
System is in program mode. .*- 
Normal functions halt on station 
13/l 7. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should...

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 28 
PROGRAM 103/l 05 
OTHER COMMON CARRIER or EQUAL ACCESS #I and #2 . 
1) Lock in the SET switch on the HKSU. 
X = LED on 
Ail LEDs off = no data 
key to place new data in 
. . * or . . . 
NOTE: Program 105 follows the same procedure as Program 103. 
Program 
105 is used to register the second OCC number used by the system. 
-54-  

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
- JANUARY 1988 
TABLE 29 
PROGRAM 104/l 06 
OTHER COMMON CARRIER AUTHORIZATION CODE LENGTHS #I and #2 ’ 
SET LED on. 
1) Lock in the SET switch on the HKSU. 
2) Depress the m key on station 13/l 7. 
3) Dial ~~~(El~~) n the dial pad. Station 13/17 LED 19 on. 
System is in program mode. F 
Normal functions halt on station 13/l 7. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
The various LEDs indicate oresent data. 
Refer to the System Record Sheet. 
This...

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 30 
PROGRAM 108/l 09 
TOLL RESTRICTION OVERRIDE CODES #I and #2 
1) Lock in the SET switch on the HKSU. 
3) Dial ilI( 0 a 1) on the dial pad. 
X = LED on 
All LEDs off = no data 
NOTE. 
SET LED goes off. 
Program 
5#XX, LED 13 enables stations to use Toll Restriction Override Codes 1 & 2. 
-56-  

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
- JANUARY 1988 
TABLE 31 
PROGRAM 1X0 
TOLL RESTRICTION CLASS PARAMETERS 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 13/17 LED 19 on. 
System is in program mode. 
2) Depress the m key on station 13/l 7. 
3) Dial 0 Hi on the dial pad. Normal functions halt on station 13/17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
An LED indicates present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should...