Toshiba Strata E Electronic Key Telephone System Installation And Maintenance Manual

rKUliHAMMlNG PRUCEOURES 
SECTION 500-036-300 
JANUARY 1988 
NOTE: 
If the access code is a single digit, enter “+” 
in the second column. If all combinations fol- 
lowing a particular first digit are to be con- 
sidered access codes (e.g., 91, 92, 93, etc.), 
enter ‘D” {D = key 18 on station 13/17) in 
the second column. 
03.30 Toll Restriction Assignments 
100 Program-Toll Restriction System Pa- 
rameters 
An entry in this program is required only if 
3- or 6-digit toll restriction is desired. Informs...

2. Enter the number of digits in the OCC Au- 
enter all allowed area codes in the upper sec- 
thorization Code (00 - 99). 
tion of the record sheet and all denied area 
3. Caution: Do not program more digits than 
codes in the lower section. Make additional co- 
required because toll restriction may be pies of the record sheet for Toll Restriction , 
defeated. 
Classes 2, 3 and 4. 
108 Program-Toil Restriction Override Code 
- #’ 
Registers the first of two codes that over- 
ride toll restriction on...

tVVJWlAMMINli HIuwmEs 
SECTION 500-036-300 
JANUARY 1988 
l Program 2XY (211 and 212) are Dro- 
garbed for area code 213 (212) and of- 
fice code 635 also (211). Class 1 stations 
are allowed to dial all office codes in area 
code 213 except 635. 
1x1 Program-Toll Restriction Class Area/ 
Office Code Exception Table Selection (X = 
Class 1 - 4) 
Entry to this program is required only if 
6,-digit (area/office code) toll restriction is de- 
sired. There are eight area/office code excep- 
tion tables...

rt T’  ? “C”  is the  stop  time  for ‘B” 
Ti.  : “‘A” 
is the  stop  time  for “C” 
elect  the priority  class required  (Programs 
X51  - 53).  Enter  the route  group 
mbers  (1 - 
4)  required  (refer to Program 
8XY). 
TE:  - 
table  is to be  used  24 hours  a day,  the 
ledule  B Start  Time must  be the  same  as 
!eduie  A Start  Time. 
0  -  63  Program-  LCR 
Route  Table. 
Time  B Schedule 
.lis  program  will define  the stop  time  for 
:~ously  selected  start time  and/or  the start 
for...

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
7) Mark an X next to 00 if the telephone or de- 
vice connected to the HI05 is to have pri- 
vacy. Leave blank if privacy is not required. 
4XX Program-Station Type Assignment 
NOTE: 
When programming, always do Program 
4XX 
before Program 4#XX. If Program 4XX 
is programmed after 4#xX the stations’ flex- 
ible key assignments will be reset to the de- 
fault data. 
Informs the system of the EKT type being 
used at each station and the order of...

1 O-key  ZO-key 
I 
FIGURE 3-Vle EKT KEY PAllERNS 
!n,  .IS the  system  of the  features  that are 
. . PROGRAMMING  PROCEDURES 
SECTION  500-036-300 
JANUARY  1988 
l Any key (except  INT) may  be assigned  a fea- 
ture  code  (Figure  4). All  assigned  feature 
codes  have priority  over 
Program  4xX as- . 
signments.  For each  key on every  station,  _ 
write  in the  name  or code  for each  feature 
to  be  assigned. 
NO  JES: 
1. A feature  (code) may be assigned  to one 
key  only,  except...

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
gram, using the various keys to change the sta- 
tus of their respective LEDs. The selections 
listed below must be repeated for each station. 
in all cases, mark an X where required. 
1) Privacy Override-mark an X next to 17 if the 
station is allowed the Privacy Override fea- 
ture. Allows an override (break-in) when a 
CO key is depressed with the CO LED on 
steady. Both parties can hear an override 
tone. 
NOTE: 
A maximum of two stations are...

blank if not allowed. (See Toil Restriction Ac- 
cess Code.) 
6) Hold Recall Time-referring to Table 1, mark 
an X next to the combination of 12, 11 and 
10 that corresponds to the recall time desired 
for each station. if ail locations are left blank, 
the timing for that station will default to that 
set in Program 05. 
TABLE 1 
HOLD RECALL TIME CODE 
7) Mark an X next to 07 if automatic off-hook 
selection is to be CO line Group 94 (defaults 
to 9 if Single CO Line Group was selected 
in Program 01)....

‘ROGRAMMING PROCEDURES 
SECTION  500-036-300 
IANUARY  1988 
u 
1) Mark  an X next  to 01  if the  station  will be 
allowed  to dial  fl + 7-digit  number.  This en- 
try  overrides  any Toll  Restriction  Class as- 
signed  to this  station. 
Mark  an X next  to 00  if this  station  will not 
be  restricted.  This entry  overrides  all other 
Toll  Restriction  programming. 
i#XX-  Program-  Station-to-Station 
Hunting 
Defines  the station  hunt destination  if the 
ailed  station  is busy. 
l Enter...

@ Paging-80 - 89 
l Trunk-Group-g, 91 - 98 
l Least Cost Routing-9 
l Door Phone/Monitor Station-66 - 68, 661 
- 673 
Enter the new 
first digit of the access code 
_ to be changed as desired. Ensure there are no 
numbering plan conflicts for proper operation. 
Example: 
Entering 13 3 4 changes the Door Phone/ 
Monitor Station access codes from 66, 67 
and 68 to 46, 47 and 48, respectively. 
*XX Program- Flexible Intercom Numbering 
Changes the system intercom number 
(2-digit) to a new intercom number...