Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual

INSTALLATION-PCB 
SECTION 200-096-206 
FEBRUARY1991 
CO LINE MODULAR  CO LINE MODULAR CO LINE MODULAR  CO LINE MODULAR 
JACK CIRCUITS 1 AND 2  JACK CIRCUITS 1 AND 2 /JACK CIRCUITS 3 AND 4  JACK CIRCUITS 3 AND 4 
BACKPLANE CONNECTOR  BACKPLANE CON 1 
FIGURE 6-8-PCOUCONTROLS,INDICATORS,ANDlNTERFACECONNECTORS 
7.02 PCOU controls, indicators, and interface con- 
nectors are shown in Figure 6-8 and described in 
Table 6-E. 
7.10 PCOU Hardware Options 
7.11 
There are no hardware options supported by 
the...

INSTALLATION-PCB 
SECTION 200-096-206 
FEBRUARY1991 
TABLE 6-E 
PCOUCONTROLS,INOICATORS,ANDlNTERFACECONNECTORS 
CONTROL/INDICATOR/ 
CONNECTOR 
(Figure 6-8) TYPE OF COMPONENT 
DESCRIPTION 
CO Line Circuit 1 
Indicator CD1 12 Red LED Lights to indicate CO line circuit 1 is in 
operation (NOTE: CO line indicator will 
not light unless PCOU is connected to 
a CO). 
CO Line Circuit 2 
Indicator CD21 2 Red LED Lights to indicate CO line circuit 2 is in 
operation (NOTE: CO line indicator will 
not light unless...

INSTALLATION-PCB 
SECTION 200-096-206 
FEBRUARY 1991 
TIE LINE 2 
TIE LINE 3 TIE LINE 4 
GROUND/ /h/f 
FACTORY 
POSITIONS) 
P403 
BACKPLANE CONNECTOR 
P103 P203 
CI~IIPC E n 
q ennli twrm~ni e nfiln ~klnlnn~fin~ riuunL v-3- rmviu cluiy i nuL3 nlYu IlVulbHI UK3 
Programs 50 - 56 
l Defines Least Cost Routing using CO lines. 
Program 78 
l Assigns special ringing of CO lines: Night Ring 
Over Page, DISA, IMDU. 
Programs 81 - 89 
l Assigns CO lines to ring selected stations. 
l Assigns Delayed Ringing to...

INSTALLATION-PCB 
SECTION 200-096-206 
FEBRUARY1991 
TABLE 6-F 
PEMU 
CONTROLS,INDICATORS,ANDlNTERFACECONNECTORS 
CONTROL/INDICATOR/ 1 
CONNECTOR 
(Figure 6-9) TYPEOFCOMPONENT 
DESCRIPTION 
TIE Line Circuit 1 
Indicator CD1 02 Red LED Lights to indicate TIE line 1 is in operation 
TIE Line Circuit 2 
Indicator CD202 
TIE Line Circuit 3 
Indicator CD302 
TIE Line Circuit 4 
Indicator CD402 Lights to indicate TIE line 2 is in operation 
Red LED 
Red LED Lights to indicate TIE line 3 is in operation 
Lights...

INSTALLATION-PCB 
SECTION 200-096-206 
FEBRUARY 1991 
TABLE 6-F 
PEMU CONTROLS, INDICATORS, AND INTERFACE CONNECTORS (continued) 
I 
CONTROL/INDICATOR 
(Figure 6-9) TYPE OF COMPONENT DESCRIPTION 
GND/BAT Jumper 
P402 
2Wl4W Jumper 
P103 Three-terminal jumper 
Three-terminal jumper M-lead origination for TIE line 4 (must 
be in BAT position per FCC requirements) 
Selects 2- or 4-wire configuration 
for E & M TIE line circuit 1. 
I 
2Wl4W Jumper 
P203 Three-terminal jumper Selects 2- or 4-wire...

INSTALLATION-PCB 
SECTION 200-096-206 
FEBRUARY1991 
50-PIN AMPHENOL CONNECTOR (FEMALE) CD4 
SW2 SMDR TTY 
. 
BACKPLANE CONNECTOR 
FIGURE 6-IO-PIOU CONTROLS, INDICATORS, AND INTERFACE CONNECTORS 
J’& NOT FACTORY 
INSTALLED FOR BELL 
MODEM SPECIFICATION 
OPTIONAL IMDU PCB 
REMOTE MAINTENANCE 
CONNECTOR 
TB 
TERMIN 
STRIP 
FlGURE6-II-PIOUS PCB SWITCH/JUMPER,OPTlON LOCATION 
6-20  

INSTALLATION-PCB 
SECTION 200-096-206 
FEBRUARY1991 
TABLE6-G 
PIOU 
CONTROLSANDINTERFACECONNECTORS . 
CONTROL/INDICATOR/ 
CONNECTOR 
(Figure 6-I 0) TYPE OF COMPONENT 
DESCRIPTION 
SMDR/TTY Interface 
Connector J3 Dual modular connector 
IMDU Connector PI 1 O-pin connector Interface connector for SMDR printer/ 
call accounting device and 
maintenance terminal/modem. 
Interface connector for Remote 
Maintenance Modem piggy-back module. 
IMDU Connector P2 g-pin connector Interface connector for Remote...

INSTALLATION-PCB 
SECTION 200-096-206 
FEBRUARY1991 
TABLE6-H 
PlOUSCONTROLSANOlNTERFACECONNECTORS 
CONTROL/INDICATOR/ 
CONNECTOR 
(Figure 6-11) TYPE OF COMPONENT DESCRIPTION 
SMDRTTY Interface 
Connector J3 Dual modular connector Interface connector for SMDR printer/ 
call accounting device and 
maintenance terminal/modem. 
IMDU Connector PI 1 O-pin connector Interface connector for Remote 
Maintenance Modem piggy-back module. 
IMDU Connector P2 g-pin connector Interface connector for Remote...

J3 
J2 
q 
q 
q 
q 
d 
q 
q 
0 
q 
q 
0 
0 -Jl 
I 
FIGURE 6-12--REMOTE MAINTENANCE MODEM 
UNIT (IMDU) INSTALLATION 
9.12 Remote Maintenance Modem Unit (IMDU) 
Installation. 
Install the Remote Maintenance Mo- 
dem Unit (IMDU) in accordance with the following 
steps: 
1) Remove the PCB from its protective packag- 
ing. 
2) Set the SW2 baud rate switch on the front panel 
to 300 or 1200, as appropriate, after the PIOU 
has been installed in the KSU (in-300 bps- 
out-l 200 bps). 
3) Set SW3 to MODEM...

INSTALLATION-PCB 
SECTION 200-096-206 
FEBRUARY 1991 
50-PIN AMPHENOL CONNECTOR (FEMALE) 
r  Pi0 PI1 
I - I .VRl I / 
-SW4 
BACKPLANE CONNECTOR 
FIGURE 6-13-PEPU CONTROLS, INDICATORS, AND INTERFACE CONNECTORS 
through programming, for the PIOU and PIOUS: 
Program 77-l 
l Assigns relay control and IMDU options. 
Program 60 
l Assigns SMDR options. 
Program 1 O-2 
l Enables External Page with All Call Page (ac- 
cess code 39 only, not AC button). 
Program 78 
l Enables Night Ringing over External Page. 
10...