Toshiba Strata Dk14, Dk40i, Dk424 Programming Manual

System & Station
Program 39 – Flexible Button Assignments
Strata DK Programming 5/993-115
System & Station
Directory Number Button Assignments
Directory Numbers are assigned to the flexible button positions on telephones. 
©Primary Directory Number Buttons [PDNs] are similar to Intercom numbers.
©Secondary Directory Numbers [SDNs] are [PDNs] which appear on another telephone.
©Phantom Directory Numbers [PhDNs] are generally used as numbers that may appear on a 
group of telephones, such as an extension...

System & Station
Program 39 – Flexible Button Assignments
3-116Strata DK Programming 5/99
  
Button TypeButton LabelsCodeNotes
Primary Directory 
Numbers [PDNs]
4-Maximum of 
same [PDN] per 
telephone[PDN] NNNN - 1, Highest button
[PDN] NNNN - 2, next highest
[PDN] NNNN - 3, next highest
[PDN] NNNN - 4, Lowest button ##YYY
##YYY
##YYY
##YYYYYY = the Program 04 station logical port 
number of the [DN] that should appear as a 
[PDN]. YYY should be the same port number 
as the port number (XXX) of the...

System & Station
Program 39 – Flexible Button Assignments
Strata DK Programming 5/993-117
System & Station
©The total number of [DNs] allowed on a telephone ([PDN], [SDNs], and [PhDNs]) is limited 
to the number of buttons on the telephone (i.e., a 20-button telephone can have 20 [DN] 
buttons).
©The number of [SDN] buttons programmed on a telephone for a given Primary Directory 
Number must always be the same as the number of [PDN] buttons that exist on the [PDN] 
owner telephone.
Example: If [PDN] 200...

System & Station
Program 39 – Flexible Button Assignments
3-118Strata DK Programming 5/99
Alert Signal Button Assignments
Station Number: _______
Station Number: _______
The Alert Signal is four short bursts of tone, sent two times/three seconds apart from one partner 
station when the other partner station when one of the partners presses the 
$OHUW6LJQDObutton 
on their telephone. An Alert Signal can be sent to stations that are idle or busy, or in Call Forward 
or Do Not Disturb mode. No talk path...

System & Station
Program 39 – Flexible Button Assignments
Strata DK Programming 5/993-119
System & Station
Alert Signal Button Programming Example
Station 200
Code
SD 
*48
Code
SD 
*47
Code
SD 
*45=
=
=
=
=
=427
202
428
203
430
204
Signal 1
Signal 2
Signal 4
Station 201
Code
SD 
*48
Code
SD 
*47
Code
SD 
*46=
=
=
=
=
=427
203
428
202
429
204
Signal 1
Signal 2
Signal 3
Station 202
Code
SD 
*48
Code
SD 
*47=
=
=
=427
200
428
201
Signal 1
Signal 2
Station 203
Code
SD 
*48
Code
SD 
*47=
=
=
=427
201
428
200...

System & Station
Program *40 – Distributed Hunt Group Member Assignments
3-120Strata DK Programming 5/99
Program *40 – Distributed Hunt Group Member 
Assignments
Processor Type:DK14, DK40i, all RCTUs
Program Type:Station
Initialized Default:No member (station port) assigned to any DH Group




  6SNU
  +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
ProcessorDH Port RangeHunt Port RangeProcessorDH Port RangeHunt Port Range
DK14 900~915 000~009 RCTUBA/BB 900~915 000~079
DK40i 900~915 000~027 RCTUC/D...

System & Station
Program *40 – Distributed Hunt Group Member Assignments
Strata DK Programming 5/993-121
System & Station
Program *40 Overview
This program assigns the members (station primary [DN] port numbers and hunting orders 
[01~32] of Distributed Hunt (DH) groups [900~915]). When a member of a DH group is added or 
deleted, all the other members’ hunting orders are automatically shifted to a new sequential order.
If Ground/Loop start CO lines ring DH Group member telephones, use Program 81~89 to...

System & Station
Program *41 for DK424 – T1 Assignment Series (Part 1)
3-122Strata DK Programming 5/99
Program *41 for DK424 – T1 Assignment Series (Part 1)
Processor Type:RCTUBA/BB, RCTUC/D and RCTUE/F
Program Type:System
Initialized Default: See each program
Series Overview
Use Program 
41 (Part 1) and 
42 (Part 2) series to set T1 parameters and assignments on the 
DK424. See the Strata DK Configuration and T1 sections for additional T1 information. RCTU 
support is as follows:
Program *41-1 – T1 Span...

System & Station
Program *41 for DK424 – T1 Assignment Series (Part 1)
Strata DK Programming 5/993-123
System & Station
Program *41-2 – T1 Channel Assignments
Initialized Default:1 = Loop Start
Important!See Program 17 for other Tie/DID assignments; see Program *17 and Program *09 
for other DID assignments.




  6SNU
  +ROG  6SNU   +ROG 7XU Q6\VWHP3RZHU2))VHFWKHQ
ProcessorLine Range
RCTUBA/BB 001~048
RCTUC/D 001~144
RCTUE/F 001~200
RDTU:___________ Slot:___________...

System & Station
Program *41 for DK424 – T1 Assignment Series (Part 1)
3-124Strata DK Programming 5/99
Notes
lYou must cycle system power or run Program 91-2 to transfer Program 
41-2 data from 
temporary memory to working memory. Turn system power OFF (five seconds) and ON after 
running Program 
41-2.
lAlways install RDTU PCBs that have Tie or DID channels in slot numbers that are higher than 
station and Attendant Console PCB slot numbers whenever possible. Each Tie or DID line 
installed uses a...