Toshiba Perception Electronic Business Communications System Installation And Maintenance Manual

rint Code Restriction Data 
Authorization Procedure must be completed. If an “OK” response is received, proceed 
as follows: 
- EXECUTE,- 
REQ 1 
NOTE 7 - The folio wing responses are possible: 
ALL = Output Code Restriction Data Block 
CRLX = Print Code Restriction List #X 
[CTR Ll /Xl = Ignore line entered 
[CTR LI [HI = Backspace 
[DEL] = Stop printing and return to REQ 
[Df L] [DEL] = Abort program 
Authorization Procedure must be completed. If an “OK” response is received, proceed 
as follows: 
NOTE...

rocedure - ‘Prim SMDR Data Block 
Authorization Procedure must be completed. If an “OK” response is received, proceed 
as follows: 
ITEM PROMPT 
1 USER ENTRY 1 NOTE 
I OK 
I FMDR 
- DISK LQADING - 
REQ 1 
NOTE I-The following responses are possible: 
PRT = Output SMDR Data Block 
[CTRL] [X] = Ignore line entered 
[CTRL] [HI = Backspace 
[DEL] = Stop printing and return to REQ 
[DEL] [DEL] = Abort program 
Procedure - Print Trunk Group Data 
Authorization Procedure must be completed. If an “OK” response...

Procedure - Print runk Data Block 
Authorization Procedure must be 
as follows: completed. If an “OK” response is received, proceed 
REQ 
I I 
NOTE I-The following responses are possible: 
PORAL L = All TDBs will be output in numerical order of ports (lowest first) 
PORNNX = TDB of Port NNX data will be output 
POR VAC = All unassigned trunk ports will be output 
TGPNN = All TDBs assigned to trunk group NN will be output 
COT = All CO Trunk Data Blocks will be output 
FEX = All FX Trunk Data Blocks will...

NOTE I- The following responses are possible: 
ALL = Output all Call Pick-up Groups listed by DN 
DNXXX= List the numbers of all Call Pick-up Groups containing DN XXX 
[CTRLI [Xl = Ignore line entered 
[CTRLJ [HI = Backspace 
[DEL] = Stop printing and return to REQ 
[DELI [DELI = Abort program 
Error Codes 
Program Name: Print Call Pick-up Groups (PCPG) 
Error Code Meaning 
ERPCP 00 Invalid response. 
ERPCP 01 Input DN does not exist. 
Procedure - Print unting Arrangements 
Authorization Procedure must...

Procedure - EKT Test Procedure 
Authorization Procedure must 
as follows: be completed. If an “OK” response is received, proceed 
ITEM 
PROMPT 
USEFI ENTRY NOTE 
OK 
TTRM 
- DISK LOADING - 
REQ 1 
NOTES: 
I. Program is now active; proceed to the EKT to be tested, and enter *TEK ( * 835) 
lo wing commands in 
~txpm~e: and the foi. 
Key Strip 11 
-..~- -.., 
8 = On (7 = Off) 
11 =On (io=offj 
, 
15 
/LED 15=On il4=6ffi 
Handset off-hook 
.-..---. -,, (check riQht volume control) 
1 Key Strip 2 ILED 2=On (1...

Procedure - Attendant Console Test 
Authorization Procedure must be completed, If an “OK” response is received, proceed 
as follows: 
ITEM 
1 f’R0iVIP-r 1 USER ENTRY 1 NOTE 
OK 
1 TTRM 
- DISK LOADING - 
REQ 
1 
NOTE: 
I. Program is now active. Proceed to the Attendant Console to be tested, depress an m key, 
and enter * TATand the following commands in sequence: 
IDial kev 7 1 ICI OPR=on,STATVCT=on, Others=off 
ev Strip 1 LPK 4 1 Associated LED=on, Others=off 
IR 
Key-Strip I MSG 
Key Strip 2 HOLD 1...

Procedure - Peripheral E. ment Diagnostic 
Authorization Procedure must be completed. if an “OK” response is received, proceed 
as follows: 
BTEM PROMPT 1 USER EiUTRY 1 NOTE 
OK 
1 TPER 
-DISK LOAQING - 
REQ I 
8 1 
- EXECUTE - 
REQ 1 
NOTE I-The following User Entries are inputted as required after each REQ prompt. 
ENTRY DESCRIPTION RESPONSE 
DSCDXXX Disable PCB XXX immediately 
PCB disabled, FALT LEDs on 
DSTKNNX Disable Trunk NNX* 
TRK disabled, FALT LED on, REQ prompted 
DSLCNNX Disable Line Circuit...

1 
DESCRIPTION 1 RESPONSE 
Set up monitor 
link using TNNX. System 
User Note 
WAIT 
[CR1 4 
STSTLK . . . or 
Auto advance to DN prompt 
STS WAIT.. . or 
[CR1 5 
STS OV R 
[DELI tCR1 6 
DN 
DN [CR1 7 
DDL 
[CR1 8 
STSTLK...or Auto advance to TRK prompt 9 
STS RLSA . . or Auto return to REQ prompt 10 
STS DDL 
[CR1 II 
TRK CALL TNNX 12 
WAIT 
tCR1 4 
STS TLK . . . or Auto advance to DN prompt 13 
STSRLSA...or Auto return to REQ prompt 10 
STS BSY . . . or Auto return to TRK prompt 14 
STS QV R Auto return...

Error Codes 
1 Procwam Name: Fioww Disk Drive Error 
 Error Code  Meanina I 
ERFD 01 File is closed. 
ERFD 02 Read error. 
ERFD 03 Write error. 
ERFD 09 File is write protected. 
ERFD IO File not found. 
ERFD II Volume not initialized. 
ERFD 12 1 File already exists. 
I 
ERFD FF 1 Other hardware causing the error.  

ITEM 
Time of Daily Routine 
Daily Routine Tasks 
Tenant Service? 
Intercept #I 
Intercept #2 
PROMPT 
REQ 
TOR 
DRT 
TEN 
ICPI 
lCP7 
ENTRY 
CHG 
Intercept #3 
lCP3 
All Page Access Code 
APG 
Not Used 
AAT 
1 Not Used 
APX 
I [CR]* 1 
Listed Directory Number *I 
Listed Directory Number #2 
LDN #I Night Number 
LDN #2 Night Number LNI 
LN2 
NT1 
NT2 
Busy Lamp Field #I 
BLFI 1 
Eusy Lamp Field #2 
Overflow DN - Attendant Console #O 
Overflow DN - Attendant Console #I 
Message Center - Tenant #0 
Message...