Toshiba Perception Electronic Business Communications System Installation And Maintenance Manual

~av. a4 PRGRAMMING (PRELIMINARY) 
PJGE a3 
1 Key Strip 2 SPARE 
I AssociatedLED=on,Others=off r- 
I I mh%s = off 
I Dial kev a 
E. Busv tone via hands& 
= Ignore line entered 
Ctl H=Backspace 
DEL =gyy=REQ 
DE&DEL= Abortprcgram 
zat 
as follows: * response is received, proceed 
LbJXl-The following User Entries areinputtedas requiredafter ea&REQ prmpt.  

PR-NG (P-NARY) 
PKiE 84 
T status m oox*~1&2~ -~---- - I status of K!F3 xxx(l&2~ I CTirmit 
. 
= FCB 
RX =Circuitnumber.  

Nov. a4 PRcmMmN(;(PRELIMINARY) 
PAGE 85 
I 
I 
I 
I 
I 
I 
I 
I 
I 
I 
I 
I 
I 
I 
I 
1 
: 
Set up monitor 
link using 
TNNX. 
i 
-L 
STSRLSA 1 Auto return to REQ prompt 
i 10 i 
. . . or e.. I I 
SrSr2SY i Auto return toTRxprcmpt 1 14 1 
e.. or 
. . . 
I I I 
*.. 
I I I 
SISRJLSA Auto return toREQ prmpt 
1. No PCB in that position 
uNAs=PCB is mipped but no data is assigned 
2. Status: IDL=Idle 
BSY=wlsy 
DIS Tl!Y=Manually disabkd via TIY 
DIS C%=EXT port disabled by software due to open cable 
DIS...

NW. 84 PRM;RAMMING (PRETJIMINARY) 
PAGE 86 
7. Enter the test center DN followed by [CR]. 
8. Allow tim for coqletion of dialing and then enter [CR]. 
9. Requested trunk was idle and has been siezed. 
10. Trunk A Omitor link) has been released due to a rralfunction or an 
outside influence, such as thedistantendgoirq on-hook (Ground Starts, 
11. Dialing was notccqletewhen [CR] was entered. Asecmd [CR] is 
required, 
12, Enter theportnunker UTNNX) of the trunk (B) tobe tested. 
l3. Requested trunk was...

Nov. 84 
PRGRMMINS (PEtFUMINARY) 
PAGE 87 
I 
I 
IERJBFF 
I Other hardware causirrgthef3rror. !  

05.09 TABLE OF CONTENTS .......................................... 
i 
TABLE LIST ................................................... ii 
INTRODUCTION ............................................... 1 
General .................................................... 1 
Customer Data .............................................. 
Utility Programs ............................................. 
I

A TTY & Modem Connections. ........................................ 
Utility Programs.. ................................................ 
AuthorizationCodeChange ......................................... 
System Data Block.. .............................................. 
AccessCode Data Block.. .......................................... 
bbreviation & Code List. ................................ 
EKTDataBlock .................................................. 
EKT Directory Number...

01.00 General 
01.01 
PERCEPTION is a stored program- 
controlled system utilizing an &bit microprocessor 
as the central processing unit (CPU). The system 
memory is made up of both Read Only Memory 
(ROM) and Dynamic Random Access Memory 
(DRAM) (the small amount of ROM that is provided 
contains the “Loader” program for the Floppy 
Disk Drive (DFDD)). When the system is first 
powered up or is reset manually, the remainder of 
the Operating System programs and Customer 
Data are loaded into DRAM from...

Pin No. Mnemonic Designation 
‘2 1 RXD / Receive Data (from TTY) 
.Ir~ 
*Connect to i-12 VDC internally 
NOTE: 
The MODEM and TTY connectors cannot be 
used simultaneously. One must be “open” 
at any given time. 
mnemonic name that is used to 
identify it and 
to call it up from the diskette. An Authorization 
Procedure must be executed before a Utility 
Program can be called up. 
The Utility Programs are listed in Table 
B, complete with their mnemonics and the title 
of the table that shows its format....