Toshiba Perception Electronic Business Communications System Installation And Maintenance Manual

3) Hang up. 
2.30.3 To cancel DND: 
1) Obtain dial tone 
3) Hang up. 
Do Not Disturb feature is no longer 
active. 
NOTE. 
Outgoing calls and features will still func- 
tion while telephone is in the DND mode. To 
all incoming features the telephone will 
appear to be busy. 
This feature allows the attendant or 
other Message Center to inform a station user 
that there is a message waiting. Your station will 
receive a double ring every 20 minutes. 
To cancel Message Waiting 
1A) Obtain dial tone. 
2A)...

IV0 TE: 
Several iID ihrnination states are used to indicate the status of a DA! 
0.5sec. on, 0.5~sec. off-indicates incoming call. 
2.0-sec. on, 0.125-sec. off, 0.125sec. on, 0.125-sec. off- 
indicates a DN in use at your EKT. 
Steady on-indicates a DN in use at another station. 
0.05sec. on, 0.05-sec. off-indicates a call on hold at your EKT. 
0.37’5~sec. on, 0.125-sec. off-indicates a call on hold at 
another station. 
DN idle. 
Dial tone must be heard before se- 
particular feature. If you have just...

You will hear outside dial tone. 
3) Dial the desired telephone number. 
dls 
To hold a call: 
press the ]FIO~] key. 
DN LED indication goes from l-use to 
l-hold. 
Connection on hold. 
2) l-lang up. 
To reconnect the call: 
1 A) Lift the handset. 
If the on-hold call was on your prime DN 
key, you will be 
reconnected immed- 
iately. 
DN LED indication goes from l-hold to 
l-use. 
‘I B) Depress the DN key(this is necessaryonlyfor 
on-hold calls not on the prime DN key). 
DN LED indication goes from...

2) The second station user depresses the 
appropriate DN key. 
The DN LED will change to l-use rate at 
both stations. 
The conference begins. 
3) Repeat to add other stations. 
NOTES. 
1. Anytime you release privacy, you can 
re-engage it immediately by depress- 
ing the DN key. 
2. Any station that is a party to the con- 
versation can release the privacy. 
A short warning tone from your EKT 
speaker (while you are talking with someone) 
advises you that an incoming call has been 
parked at your...

To answer Automatic Callback: 
Lift the handset. 
4 If the called party is a trunk, you will hear an 
outside dial tone (proceed to dial). 
RIO E: 
If the calf was made using Least Cosi Rout- 
ing, the called number will be dialed automat- 
ically at this point. 
W If the called party is a station, that station will 
ring and you will hear the ringback tone. 
d If you hear overflow tone, the station or trunk 
you called has been previously called, hang 
up and wait to be called again. 
To cancel...

1) Obtain dial tone. 
2) Dial the access code (see below) for the 
desired zone. 
Pagin CC@SS Codes 
(location) 
ZONE I 
ZONE 2 
ZONE 3 
ZONE 4 
ZONE 5 
ALL ZONE 
3) Speak slowly and distinctly, and repeat your 
message. 
0 This feature will automatically connect 
you to a call that has been “parked” for you by the 
operator. If you are away from your telephone, the 
operator may park the call and direct you via the 
page system to dial an access code. 
NO TE. 
you may continue to place outgoing calls...

SC0 LED will go on. 
Call will now ring at your EKT. 
To release Speaker Cut-off: 
Depress the &CO] key. 
SC0 LED will go off. 
Handsfree Answerback is active 
.I This feature allows you to be con- 
nected automatically to the speaker of a specific 
EKT. 
To voice page: 
I) Obtain dial tone. 
press the appropriate voice page key. 
You will hear one ring tone. 
VP LED will flash once. 
3) Wlake announcement. 
NO l-E: 
lf that person is busy on another DiV or has 
SC0 engaged, you will hear ring tone until...

2.3 To store a telephone number: 
1) Leave the handset on-hook. 
2) press the L/$0 key. 
The ADL LED will wink. 
3) Dial the telephone number to be stored (16 
digits maximum). 
NOTE. 
It may be necessary to insert a pause to allow 
for dial tone delay. If so, depress the 
q key 
after the trunk access code. 
4) Depress the 1x1 key. 
ADL LED goes off and the telephone 
number is stored. 
m3llk-l 
This feature allows you to signal a spe- 
To signal the station: 
press the m key. 
The SIG LED will flash...

3) Dial the account number on the dial pad 
L..-..- digits). 
When the number is completed, you will 
hear dial tone again. 
4) Dial the call in the usual manner. 
To record an account number during a 
call (incoming or outgoing without a [?Ikq key)- 
At any time before disconnect... 
I) Ask your party to wait. 
3 press the [CON7 key. 
Connection on hold. 
You will hear recall dial tone. 
3) DialmB. 
4) Dial the account number ( digits). 
When the number is completed, you will 
hear recall dial tone...

Al0 TE. 
If you go off-hook while your station is being 
signalled by the IViessage Waiting feature, 
you will be connected automatically to the 
Message Center. 
essa enter 
atio 
The following applies only if your EKT is 
designated as the Message Center. 
.3 To leave a message waiting signal: 
I) Dial the appropriate station number. 
2) If busy or no answer, depress [%!] key. 
MSG LED on (both stations). 
The Message Center MSG LED goes off 
when the connection is broken. 
.3 To cancel message waiting...