Toshiba L350 Manual

							
51Getting Started
Adding memory (optional)
6Using a small Phillips screwdriver, loosen the captive screw 
that secures the memory module slot cover.
 (Sample Illustration) Removing the memory module slot cover
7Remove the memory module slot cover.
8 Place the screw and the cover in a safe place so that you can 
retrieve them later.
Static electricity can damage the memory module. Before you handle 
the module, touch a grounded metal surface to discharge any static 
electricity you may have built up.
Avoid touching the connector on the memory module or on the 
computer. Grease or dust on the connector may cause memory 
access problems.
9 Carefully remove the new memory module from its antistatic 
packaging, without touching its connector.
10 Locate an empty memory module  slot on the underside of the 
computer. 
If no memory slot is available, you must remove a module by 
performing steps  2-3  of  “Removing a memory module” on page 54 .
Back of computer
NOTE 
						

							
52Getting Started
Adding memory (optional)
If your system has the memory modules stacked on top of one 
another, you must remove the top module first before 
removing/installing the bottom module.
For this model Slot A is the bottom slot. Slot B is the top slot. If only 
one memory module is to be installed, it must be installed in slot A.
11 Pick up the memory module by its sides, avoiding any contact 
with its connector. Position the module toward the socket, 
aligning the connector’s notch with the matching key in the 
socket.
(Sample Illustration) Aligning the memory module with the socket
12 Firmly press the memory module into the memory slot’s socket 
at approximately a 30-degree  angle (to the horizontal surface 
of the computer).
(Sample Illustration) Inserting the memory module into the socket
NOTE
NOTE
latch
latch
key notch
connector 
						

							
53Getting Started
Adding memory (optional)
13Once the module’s connector is fu lly inserted into the socket, 
press downward on the top edge of the module to seat the 
module into the latches at the sides of the socket. These latches 
should “snap” into place securely with the corresponding 
cutouts in the side of the module. If the latches and cutouts do 
not line up correctly, repeat steps  12-13 .
(Sample Illustration) Pressing down on the memory module Do not force the memory module into position. The memory 
module should be completely inserted into the socket and level 
when secured in place.
 (Sample Illustration) Inserting the memory module into the slot
For this model Slot A is the bottom slot. Slot B is the top slot. If only 
one memory module is to be installed, it must be installed in slot A.
latch
latch
Slot BSlot A
NOTE 
						

							
54Getting Started
Adding memory (optional)
14Replace the memory modu le slot cover and secure it using the 
screw.
15 Re-insert the main battery. For more information on inserting 
the main battery, see  “Inserting a charged battery” on page 105 .
16 Turn the computer right side up.
17 Reconnect the cables.
18 Restart the computer.
TECHNICAL NOTE: You must have at least one memory module 
installed for the computer to work.
You can now continue setting up the computer. When the operating 
system has loaded, you can verify that the computer has recognized 
the additional memory module.
If you are adding extra memory after setting up the computer, verify 
that the computer has recognized  it correctly as described in 
“Checking total memory” on page 56 .
Removing a memory module
If you need to remove a memory module:
1Complete steps  1–8 in  “Installing a memory module” on 
page 49  to shut down the computer and open the memory 
module slot cover.
Do not try to remove a memory module with the computer turned on. 
You can damage the computer and the memory module.
Do not remove the memory module while the computer is in Sleep or 
Hibernation mode. The computer could hang up the next time you 
turn it on and data in memory will be lost. In either of the above 
cases, the Sleep configuration will not be saved. 
						

							
55Getting Started
Adding memory (optional)
The following screen may appear when you turn on the power:
 
If “Start Windows® Normally” is highlighted, then press Enter.
If one of the Safe Mode options is highlighted, it is best to press 
Enter to go into Safe Mode, then shut down and restart the system, at 
which time Windows® should boot back up normally.
When Safe Mode is suggested, this could be a sign that you may 
need to scan your hard drive for errors or defragment the drive. If so, 
consult Windows® Help and Support.
2 Pull the latches away from the memory module.
The memory module pops up slightly.
If your system has the memory modules stacked on top of one 
another, you must remove the top module first before 
removing/installing the bottom module.
3 Gently lift the memory module to  a 30-degree angle and slide it 
out of the slot.
 (Sample Illustration) Removing the memory module
NOTE
NOTE
Slot BSlot A 
						

							
56Getting Started
Adding memory (optional)
4Replace the memory modu le slot cover and secure it using the 
screw.
5 Re-insert the main battery. For more information on inserting 
the main battery, see  “Inserting a charged battery” on page 105 .
6 Turn the computer right side up.
7 Reconnect the cables.
8 Restart the computer.
TECHNICAL NOTE: You must have at least one memory module 
installed for the computer to work.
Checking total memory
When you add or remove a memory  module, you can check that the 
computer has recognized the change. To do this:
1 Click  Start, Control Panel , and then System.
The  System  window appears.
2 The total memory is displayed below the System heading 
under  Memory (RAM) .
If the computer does  not recognize the memory configuration, turn 
off the computer and remove the memory module slot cover 
(complete steps  1-8  in  “Installing a memory module” on page 49 ), 
and then check that the module is inserted completely into the 
socket and lined up squarely with the socket latches.
From time to time, Windows® will display a pop-up that says, 
“Windows® needs your permission to continue.” This is a security 
feature to prevent programs or people from doing things on your 
computer without your permission. If you were trying to perform the 
action, click Continue; otherwise, click Cancel. If unsure, cancel and 
try again.
NOTE 
						

							
57Getting Started
Using the TouchPad™
Using the TouchPad™
The TouchPad™, the small, rectangular area located in front of the 
keyboard, is sensitive to touch and enables you to move the cursor 
with the stroke of a finger. Simply move your finger on the 
TouchPad in the direction you would like to move the cursor: 
❖ To move the cursor to the top of the page, push your finger 
forward on the TouchPad.
❖ To move the cursor to the bottom of the page, drag your finger 
toward yourself.
❖ To move the cursor to the right side of the page, slide your 
finger across the TouchPad  from left to right.
❖ To move it to the left side, slide your finger from right to left.
Because the TouchPad is much smaller than the display screen, 
moving your cursor across the screen often means having to move 
your finger several times across the TouchPad in the preferred 
direction.
Once you have positioned your cursor , you can click it into place by 
either double-tapping the TouchPad or clicking the control buttons.
Scrolling with the TouchPad™
There are two active regions on the TouchPad™ that allow you to 
scroll as you would with any wheel device on a mouse or trackball.
To scroll vertically, run your finger up or down along the right edge 
of the TouchPad. To scroll horizontally, run your finger along the 
bottom edge of the TouchPad. This feature can be disabled or 
changed in the Mouse Pr operties dialog box.
Control buttons
When a step instructs you to clic k or choose an item, move the 
cursor to the item, then press an d release the primary (left-hand) 
button. To double-click, press the primary button twice in rapid 
succession. The primary button usually corresponds to the left 
mouse button.
The function of the secondary (right-hand) button depends on the 
program you are using. It usually corresponds to the right mouse 
button (“right-clicking”). Check your program’s documentation to 
determine whether it uses the right mouse button.
NOTE 
						

							
58Getting Started
Using external display devices
Disabling or enabling the TouchPad™
The TouchPad™ is enabled by default. To change the enable/disable 
TouchPad setting, press 
Fn + F9. This hot key enables/disables the 
TouchPad. For more information, see  “Disabling or enabling the 
TouchPad™” on page 190 .
Using external display devices
Your computer comes with a built-in display, but you can also 
connect an external display device to an available video port.
Connecting an external monitor or projector
You can easily attach an external  monitor or projector to your 
computer if you need a larger screen. To do this:
1 Connect the monitor’s video cable to the RGB (monitor) port 
on the side of the computer.
2 Connect the device’s power cable to a live electrical outlet.
3 Turn on the external device.
Your computer will automatically detect the external display 
device and activate a scr een with display options.
4 Select the settings you desire and click  Apply.
5 Click  OK.
Directing the display output  when you turn on the computer
Once you have connected an exte rnal display device, you can 
choose to use the internal display  only, the external device only, or 
both simultaneously. 
Some modes are only available with  the appropriate device attached 
and turned on.
The quickest way to change the display output settings is to use the 
display hot key (
Fn + F5):
1 Press 
Fn and F5 simultaneously.
NOTE 
						

							
59Getting Started
Using external display devices
2While holding down Fn, press F5 repeatedly until the setting 
you want takes effect. Briefly pause each time you press the 
F5 
key to allow time for the display to change.
This hot key cycles through the settings in the following order 
(the last two options are availa ble if an external monitor is 
connected):
❖ LCD—Internal display only
❖ LCD + CRT—Internal display and external monitor 
simultaneously
❖ CRT—External monitor only
❖ LCD + CRT Multi Monitor—Internal display and external 
monitor, with one acting as  the primary display and the 
other as an extended desktop
❖ Swap—Switch primary display between internal display 
and external monitor when using extended desktop
(Sample Image) Display options window
3 Release the 
Fn key.
Adjusting the quality of the external display
To obtain the best picture quality from your television (or other 
video display device), you may need to adjust the video settings. 
See the video device documentation for additional configuration 
steps. 
						

							
60Getting Started
Using an external keyboard
Using an external keyboard
If you prefer to use a full-size keyboard, you can attach one to your 
computer. The computer’s USB ports support any USB-compatible 
keyboard.
Using a mouse
You may want to use a mouse instead of the computer’s built-in 
TouchPad. You can use a USB-compatible mouse.
Connecting a printer
Your printer documentation may require you to install the printer 
software before physically connecting the printer to your computer. If 
you do not install the software as instructed by the printer 
manufacturer, the printer may not function correctly.
Read the documentation that came with your printer. Follow the 
manufacturer’s instructions when connecting a printer.
You can connect a USB-compatible printer to your computer 
through the USB ports. To determine if the printer is USB-
compatible, check its documentation.
To make the connection, you need a suitable USB cable which may 
come with your printer. If a USB cable was not included with your 
printer, you can purchase one from a computer or electronics store.
If your printer supports Plug and Play, your computer may 
automatically recognize the printer; th e printer is then ready for use. 
Refer to your printer documentation for further instructions.
TECHNICAL NOTE: To determine if your printer supports Plug and 
Play, check its documentation.
If your printer does not support Plug and Play, you can set up the 
printer as described in  “Setting up a printer” on page 61 .
To connect a printer to your computer:
1 Connect the printer cable to th e printer and then connect the 
other end to one of the computer’s USB ports.
2 Plug the printer’s power cable into a live AC outlet.
NOTE