Toshiba Estudio 170f Manual

179
If communication errors fre-
quently occur while transmit-
ting documents due to bad line
conditions, we recommend you
select a lower transmission
speed to enable quality trans-
missions. The transmission
speed will be restored to the
default value automatically af-
ter the low speed transmission
is completed.
You can activate this option
while programming an Abbrevi-
ated Dial Number (page 66)  or
One Touch Dial Key (page 72)
if communication with a certain
remote party always requires
this option....

180This function is used to set the
facsimile’s speaker ON in order
to monitor the phone line for
one communication only. This
function is mainly used to con-
firm dialing and phone line sta-
tus.
You can activate this option
when programming an Abbrevi-
ated Dial Number (page 66)  or
One Touch Dial Key (page 72)
if communication with a certain
remote party always requires
this option.Press:
+
+ Load the document face down
in the Document Support (see
page 83).
Adjust the resolution and con-
trast if...

181
When this function is set to
ON,  the designated number of
pages will be printed at the top
of the recording paper at the
remote station. This function is
effective for a Direct Document
Transmission only. (The total
number of pages will  be print-
ed automatically as part of the
TTI in Memory Transmissions.)
This setting is very helpful for
confirming that all of the pages
loaded  into the feeder have
been successfully sent.
It will also assist the recipient
to track the number of pages
as it will...

182
To set the e-STUDIO170F to
always print a communication
report, press: You can request a communica-
tion report every time a docu-
ment is sent. If you desire a
communication report every
time you send a document, set
this function to ON as a default
(see page 183).
If you plan to use communica-
tion reports only occasionally,
use this procedure. The TX Re-
port key allows you to obtain a
report for one communication
only.
You can activate this option
while programming an Abbrevi-
ated Dial Number...

183
This facsimile allows the operator to set various options regarding
the lists and reports listed below.
JOURNAL
There are two types of Journals available on the e-STUDIO170F.
Both the Transmission Journal (TX Journal) and Reception Journal
(RX Journal) list the 40 most recent transactions. Journals can be
printed either Automatically or Manually. When manually printed,JOURNAL
 must be pressed. To select the type of Journal to print when
JOURNAL
 is pressed, complete manual Journal printing discussed...

184Press the following key to
setup automatic printing of the
TX and RX Journals whenever
40 transactions have taken in
place.
To turn ON Automatic printing
of journal, press:
AUTO PRINT
Options
4Reception Journal Settings - continuedCOMPLETED
Press 
STOP
 to complete this
setting. To turn OFF Automatic printing
of journal, press:
The following screen is dis-
played for 2 seconds to con-
firm your selection. 

185
Select the desired printing op-
tion for non-memory, direct
transmissions.
To ALWAYS print a Transmis-
sion Report whenever a docu-
ment is transmitted, press:
Press:
+
+
+
+
+
+
Display the TX
REPORT Menu
1
Select the Option for
TX REPORT
2
Direct Transmission Report Setting
COMPLETED
MENU
Press 
STOP
 to complete this
setting. To only print a Transmission
Report when an error occurrs,
press:
To turn OFF automatic printing
of Transmission Reports,
press:
The following screen is dis-
played for 2...

186Press:
+
+
+
+
+
+
Memory Transmission Report SettingDisplay the
MEMORY TX
Menu
1
To print a first page image of
the document on the Transmis-
sion Report, press:
Select the Option for MEMORY TX
2
Set the Option for
SHOW FIRST PAGE
3
COMPLETED
COMPLETED
Press 
STOP
 to complete this
setting.
MENU
Select the desired printing op-
tion for single location memory
transmissions.
To ALWAYS print a Transmis-
sion Report whenever a docu-
ment is transmitted, press:
To only print a Transmission
Report when an...

187
Press:
+
+
+
+
+
+
Multi-Address Report SettingDisplay the
MULTI-ADD
REPORT Menu
1
Select the desired option for
Multi-address Transmission Re-
ports.
To ALWAYS print a Transmis-
sion Report whenever a docu-
ment is transmitted, press:
To print a first page image of
the document on the transmis-
sion report, press:
Set the Option for
SHOW FIRST PAGE
3
3.OFF2.ON ERRORMULTI-ADD REPORT
1.ALWAYS
COMPLETED
2.OFFSHOW FIRST PAGE
1.ONSelect the Option for MULTI-ADD REPORT
2
COMPLETED
MENU
Go to Step 3.Press...

188Press:
+
+
+
+
+
+
Multi-Polling Report SettingDisplay the
MULTI POLL
REPORT Menu
1
Select the desired option for
Multi-polling Reports.
To ALWAYS print a report
whenever a polling operation
occurs, press:
MULTI POLL
REPORT Options
2
3.OFF2.ON ERRORMULTIPOLL REPORT
1.ALWAYS
COMPLETED
MENU
Press            to complete this
setting. To only print a report when an
error occurrs, press:
To turn OFF automatic printing
of this report, press:
The following screen is dis-
played for 2 seconds to con-
firm...