Toshiba Estudio 170f Manual

209
If an abnormal condition arises
in the facsimile or an incorrect
operation is performed, an
alarm buzzer is generated for
about 4 seconds and a mes-
sage to indicate the nature of
the error appears in the LCD
window. In that case, take cor-
rective action according to the
following table.
Autodialer numbers and initial set-
tings have been lost (due to a long
period without power or a deplet-
ed backup battery).Press 
STOP
 to restore the idle
state. If this Error Message is re-
peatedly displayed,...

210
No paper exists in the upper pa-
per tray. This error occurs with
an optional paper tray installed.Supply recording paper to the
upper paper tray.No paper exists in the lower pa-
per tray. This error occurs with
an optional paper tray installed.Supply recording paper to the
lower paper tray.No recording paper exists in any
paper tray.Supply recording paper to the
paper tray(s).The toner is nearly exhausted
(warning).Replace the toner.The toner is exhausted.Replace the toner (see page
30).The drum...

211
Paper Jam Error Codes
If a paper jam occurs during a reception or copying operation, the message “PA-
PER SIZE ERROR OR PAPER JAM XX” is displayed. If this occurs, follow the pro-
cedure below.
The code number “XX” indicates the location of the paper jam as shown in the table
below.Error
Code
Cause How to Correct
10
20
80
90A paper jam has occurred in the
Recording Paper Tray or Bypass
Tray.
A paper jam has occurred in the
Optional Recording Paper Tray.
A paper jam has occurred at the
paper feed...

212When an Error Code is printed as a status indication on Transmission Reports, etc., refer to the following description for the applicable Error Code to determine the cause.Error
Code
Cause How to Correct
10
11
12
13
20
E0
E6
30
32
33Paper Empty
Recording Paper Jam
Document Paper Jam
Cover Open
Power Failure
Error relating to the printer or
memory.
          was pressed during the
communication.
Page # Mismatch
Polling ErrorLoad recording paper and set the
tray.
Open the cover and clear the re-
cording...

213
Too many document pages
are set.
The Operation Panel is not
closed fully.
The document extension
Tray is not fully extended.
Something is wrong with
the document paper itself.
The ADF pad is dirty.
The document was loaded
with a wrong side down.
The Operation Panel is not
closed fully.
The remote party’s unit is
not compatible with yours.
Poor telephone line condi-
tions. When transmissions are not performed normally, check the points in the table be-
low.  If the facsimile will not operate correctly...

214When receptions are not performed normally, check the points in the table below.
If the facsimile will not operate correctly after confirming these points or anything
not listed here occurs, call your service representatives.
When you are to re-
ceive a document
and you pressSTART
 nothing hap-
pens.
ProblemCauseSolution
A document is still in your
facsimile.
The modular cord (tele-
phone line cable) is dis-
connected.
There is no power to the
unit.
There is no recording pa-
per.
The RX cover is not...

215
If a document jam occurs dur-
ing a transmission, the mes-
sage “DOCUMENT JAM” is
displayed in the LCD window.
Follow this procedure to clear a
document jam.
Leave the power of the fac-
simile ON.
Remove other documents from
the Document Support, if any
(except the jammed portion).Open the Operation Panel. Remove the jammed docu-
ment.  Check for pieces of pa-
per, clips, or staples which
may have caused the failure.Firmly close the Operation
Panel.
Confirm that the LCD display
indicates that the...

216If a recording paper jam occurs
during a reception or a copying
operation, the message “PA-
PER SIZE ERROR OR PA-
PER JAM XX” is displayed in
the LCD window. Follow this
procedure to clear the jam.
The code number “XX” indi-
cates the location where the
paper jam has occurred as
shown in the table below.
Leave the power of the fac-
simile ON.
Remove any document or re-
cording paper from the Docu-
ment Support, Document Exit
Tray or Recording Paper Exit
Tray.Remove the jammed paper
from the Bypass...

217
Replace the Bypass Tray. Remove the Optional Record-
ing  Paper Tray.
Clearing a Recording Paper Jam - continuedReplace the Bypass
Tray
5
Remove the stack of paper
from the Optional Recording
Paper Tray and remove the
jammed paper from the ma-
chine.
Pull Out the Optional
Recording Paper Tray
6
Remove the Jammed
Paper (Optional
Recording Paper Tray)
7
Insert the Optional Recording
Paper Tray all the way into the
machine.
NOTE:
As the tray is inserted, lis-
ten for the sound of the pa-
per pressure...

218Lift up and holding the green
handle, gently pull out the Pro-
cess Unit.
CAUTION:
Always hold the Process
Unit by the green handle.
Clearing a Recording Paper Jam - continued
Remove the jammed paper in
the direction of the arrow.
Avoid tearing the paper.
CAUTIONS
• Do no touch the image
Transfer Roller.
• The black colored fuser
housing may be hot if
the machine was in use
prior to this paper jam.
Remove the Process
Unit
10
Remove the Jammed
Paper
(Paper Feed Area)
11NOTE:
It is recommended to fold...