Toshiba Bsa4tp User Manual

2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.7 Setting an Operating Environment
 
E2-28 
2.7.3  IP Address Setting  (TCP/IP) (Cont.) 
 
 
 
  (4)  Socket Port  
This parameter is to enable a socket port and set a socket number.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
(5) DHCP  
This parameter is to enable DHCP. 
 
 
PORT ON  0800
0 
IP ADDRESS 
DHCP 
PORT ON  08000 PORT OFF ----- 
PORT ON  08000 
PORT ON  0 8000 
SOCKET PORT 
[RESTART]  or [FEED] 
[PAUSE] 
[PAUSE] 
Enter a number...

2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.7 Setting an Operating Environment
 
E2-29 
2.7.3  IP Address Setting  (TCP/IP) (Cont.) 
 
 
 
 
 
 
 
 
  (6)  DHCP Client ID 
This parameter is to set a DHCP client ID. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
ASCII code and Hex. code correspondence table 
Upper 4 bits
Lower 4 bits 2 3 4 5 6 7 
0 SP 0 @ P ` p 
1 ! 1 A Q a q 
2 “ 2 B R b r 
3 # 3 C S c s 
4 $ 4 D T d t 
5 % 5 E U e u 
6 & 6 F V f v 
7 ‘ 7 G W g w
8 ( 8 H X h x 
9  ) 9 I Y i y 
A * : J Z j...

2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-30 
2.8  Installing the Printer Drivers 
2.8.1. Introduction 
This manual describes how to install the TOSHIBA printe r driver for the TOSHIBA B-SA4T bar code printer on 
your Windows host computer; install and delete the pr inter driver, the procedure for adding the LAN port, 
cautions and limitations.  The appropriate  version of the printer driver is V6.9. 
 
2.8.2. General Description 
(1) Features 
Once you install...

2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-31 
2.8.3.  Installing the Printer Driver 
The installation procedure differs depending on the interf ace connected to the printer and the operation system 
you are using.  Please install the printer driver by performing the appropriate procedure. 
If the previous version of the printer driver has been  installed on your host computer , be sure to uninstall it 
before you install this printer driver.  (Refer to  Section...

2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-32 
  (1) 
Select “Settings” – “Printers” from the “Start” menu to open the printer folder. 
(2)  Double-click on the “Add Printer” icon.   The Add Printer Wizard runs.  Click on the [Next] button. 
(3)  Select “Local printer”, then click on the  [Next] button.  The screen listing “Manufacturers and 
Printers” is displayed. 
(4)  Click on the  [Have Disk…] button.  The “Install From Disk” dialog box is displayed....

2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-33 
 
(1)  Log on to your host computer as a member who has full control access privilege concerning the  printer settings. 
(2)  Select “Settings” – “Printers” from the  “Start” menu to open the printer folder. 
(3)  Double-click on the “Add Printer” icon.   The Add Printer Wizard runs.  Click on the [Next] button.  
(4)  Select “My Computer”, then click on the  [Next] button. 
(5)  Select the port to be used for...

2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-34 
 
(1)  Log on to your host computer as a member who has full control access privilege concerning the  printer settings. 
(2)  Select “Settings” – “Printers” from the  “Start” menu to open the printer folder. 
(3)  Double-click on the “Add Printer” icon.   The Add Printer Wizard runs.  Click on the [Next] button. 
(4)  Select “Local printer”.  Mark off the “Automati cally detect and install my Plug and Play printer”...

2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-35 
(2)  USB INTERFACE 
Installation starts by the operating system’s plug-and-play function.   
Windows 95 and Windows NT4.0 do not support the USB interface. 
 
 
 
(1)  Turn the printer ON, then connect it to  your host computer with the USB cable.   
  The “New Hardware Found” dialog box is di splayed, and “USB Device” is detected. 
  
 
(2)  After a while, the “Add New Hardware Wizard” dialog box is display\
ed....

2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-36 
(3)  Select “Search for the best driver for your device. (Recommended)”. 
  Mark the “Specify a location” checkbox, then click on the  [Browse] button. 
 Specify “\ driver\WinMe-9x ” folder, then click on the  [Next] button. 
  
 
(4)  Check to see that the “USB Printing Suppor t” driver is detected, then click on the [Next] button. 
    

2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-37 
(5)  When the screen which indicates the USB Prin ting Support driver has been installed, is 
displayed, click on the  [Finish] button. 
  
 
(6)  After a while, “ TEC B-SA4T” is detected as a new hardware. 
  
 
(7)  The “Add New Hardware Wizard” dialog box is displayed.    Select “Specify the location of the driver (Advanced)”, then click on the  [Next] button.