Toshiba Bsa4tp User Manual

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.7 Setting an Operating Environment
 
E2-28 
2.7.3  IP Address Setting  (TCP/IP) (Cont.) 
 
 
 
  (4)  Socket Port  
This parameter is to enable a socket port and set a socket number.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
(5) DHCP  
This parameter is to enable DHCP. 
 
 
PORT ON  0800
0 
IP ADDRESS 
DHCP 
PORT ON  08000 PORT OFF ----- 
PORT ON  08000 
PORT ON  0 8000 
SOCKET PORT 
[RESTART]  or [FEED] 
[PAUSE] 
[PAUSE] 
Enter a number for each digit of the 
port number with the 
[RESTART] or 
[FEED] key.  
[PAUSE] 
[PAUSE]
NOTES: 
1. Pressing the  [PAUSE] key 
while “PORT ON 08000” is 
displayed allows you to set the 
port number.  
2.  Set a number for each digit by  using the 
[RESTART] or 
[FEED] key.  
 
[RESTART] key: Increment 
 
[FEED] key: Decrement 
  Range: 00000 to 65535 
  A number exceeding 65535 will  be automatically corrected to 
65535. 
3.  Be careful not to set the same 
port number that other 
applications are using. 
4. Press the  [PAUSE] key to move 
the cursor to the next digit. 
5.  After the last digit is set, press  the 
[PAUSE] key to go to 
DHCP Setting.  
NOTE: 
Pressing the  [PAUSE] key while 
“DHCP ON” is displayed allows 
you to set a DHCP client ID. 
IP ADDRESS 
DHCP      ON 
IP ADDRESS 
DHCP CLIENT ID 
IP ADDRESS 
DHCP 
IP ADDRESS 
DHCP      OFF 
[PAUSE] 
[PAUSE][RESTART]  or [FEED]  
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.7 Setting an Operating Environment
 
E2-29 
2.7.3  IP Address Setting  (TCP/IP) (Cont.) 
 
 
 
 
 
 
 
 
  (6)  DHCP Client ID 
This parameter is to set a DHCP client ID. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
ASCII code and Hex. code correspondence table 
Upper 4 bits
Lower 4 bits 2 3 4 5 6 7 
0 SP 0 @ P ` p 
1 ! 1 A Q a q 
2 “ 2 B R b r 
3 # 3 C S c s 
4 $ 4 D T d t 
5 % 5 E U e u 
6 & 6 F V f v 
7 ‘ 7 G W g w
8 ( 8 H X h x 
9  ) 9 I Y i y 
A * : J Z j z 
B  +  ; K [  k { 
C , < L \ l | 
D - = M ] m } 
E . > N ^ n  
F / ? O _ o  
  SP = Space 
 
(Example)  To enter “TOSHIBA” in Hex. code: 
 
  54 4F 53 48 49 42 41  
 
 
When the system mode settings have b een completed, turn off the printer. 
IP ADDRESS 
DHCP CLIENT ID 
MODE      ASCII 
DHCP CLIENT ID  MODE      HEX 
DHCP CLIENT ID 
4142434445464748 
494A4B4C4D4E4F50 
[PAUSE]
[PAUSE]
[FEED] or [RESTART]  
[PAUSE] Hex. Code
MODE          ASCII 
ABCDEFGHIJKLMNOP
ASCII Code[PAUSE] 
Enter a character or a value for each of 1st byte to 16th 
byte sequentially using the 
[FEED] or [RESTART]  key. 
[PAUSE]
NOTES: 
1.  Code used to enter a DHCP  client ID is selectable between 
ASCII code (alphanumeric) and 
Hex code.  
2.  Set a character or value for 
each byte by using the 
[RESTART] or [FEED] key.  
 
[RESTART] key: Increment 
 
[FEED] key: Decrement 
3. Press the  [PAUSE] key to enter 
the next byte.  Repeat this until 
16th byte is entered.  
4.  After the 16th byte is set, press 
the 
[PAUSE] key to store the 
entered DHCP client ID.  At this 
time, the display will turn to 
IP ADDRESS.   
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-30 
2.8  Installing the Printer Drivers 
2.8.1. Introduction 
This manual describes how to install the TOSHIBA printe r driver for the TOSHIBA B-SA4T bar code printer on 
your Windows host computer; install and delete the pr inter driver, the procedure for adding the LAN port, 
cautions and limitations.  The appropriate  version of the printer driver is V6.9. 
 
2.8.2. General Description 
(1) Features 
Once you install the TOSHIBA printer driver on your Windows host computer, you can use the TOSHIBA 
B-SA4T bar code printer, as well as the easy-to-use general printers. 
You can use this printer by connecting a parallel interf ace cable (printer cable), a USB cable, or a LAN cable 
to your host computer. 
 
(2) System Requirements 
To install the TOSHIBA printer driver on your host computer, the following system and environment are 
required: 
•  Operating system:  Windows 95, Windows 98, Windows Me, Windows NT4.0, Windows 2000, 
Windows XP 
•   Hardware:  A DOS-/V (IBM PC/AT compatible) machine running an above operating system. 
•   Interface:  • Parallel interface conforming to the IEEE1284 standard  
    (Compatibility and ECP modes) 
  • USB interface (Ver1.1) 
*1 
  • LAN interface (10BASE-T/100BASE-TX) 
*1: Windows 95 and Windows NT4.0 do not support the USB connection.  
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-31 
2.8.3.  Installing the Printer Driver 
The installation procedure differs depending on the interf ace connected to the printer and the operation system 
you are using.  Please install the printer driver by performing the appropriate procedure. 
If the previous version of the printer driver has been  installed on your host computer , be sure to uninstall it 
before you install this printer driver.  (Refer to  Section 2.8.4 Uninstalling the Printer Driver .) 
To print via your network, please install the printer dr iver by performing the installation procedure for the 
parallel interface, and also perform the following: 
  1.  In the procedure, select “LPT1” for the port. 
  2.  After installation of the printer driver  is completed, add the LAN port by referring to  Section 2.8.5 
Adding/Deleting a LAN Port , and specify the LAN port. 
 
(1) Parallel Interface 
To use the parallel interface, the following settings  are required, after installing the printer driver: 
For Windows 95/98/Me:  Open  the  printer  properties.    Select the “Details” tab and click on the 
[Spool Settings…]  button.  The “Spool Settings” dialog box is displayed.  
Select “Disable bi-directional support for this printer”. 
For Windows NT/2000/XP:  Open the printer properties a nd select the “Ports” tab.  Mark off the “Enable 
bidirectional support” checkbox.  
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-32 
  (1) 
Select “Settings” – “Printers” from the “Start” menu to open the printer folder. 
(2)  Double-click on the “Add Printer” icon.   The Add Printer Wizard runs.  Click on the [Next] button. 
(3)  Select “Local printer”, then click on the  [Next] button.  The screen listing “Manufacturers and 
Printers” is displayed. 
(4)  Click on the  [Have Disk…] button.  The “Install From Disk” dialog box is displayed. 
Specify the “ \driver\WinMe-9x ” folder in the CD-ROM drive, then click on the  [OK] button. 
 
 
 
(5)  Select the printer to be installed from “Printers” list, then click on the  [Next] button. 
(6)  The screen to select the existing installed printer  driver or use the new one, is displayed.  Select 
“Replace existing driver”, then click on the  [Next] button.  If you install the printer driver for the first 
time, this screen is not displayed. 
(7)  Select the port to be used for printing fro m the “Available ports” list, then click on the  [Next] button. 
(8)  Change the printer name if necessary, and select  whether or not you use the printer as the default 
printer (“Yes” or “No”).  Click on the  [Finish] button. 
(9)  The printer driver is installed.  When installati on is completed, the new printer icon is added in the 
“Printers” folder. 
 
Windows 95/98/Me 
NOTE : 
The latest printer driver is available from the web site, “ the Barcode Master”. 
(http://barcode.toshibatec.co.jp/Eng/index.html)  
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-33 
 
(1)  Log on to your host computer as a member who has full control access privilege concerning the  printer settings. 
(2)  Select “Settings” – “Printers” from the  “Start” menu to open the printer folder. 
(3)  Double-click on the “Add Printer” icon.   The Add Printer Wizard runs.  Click on the [Next] button.  
(4)  Select “My Computer”, then click on the  [Next] button. 
(5)  Select the port to be used for printing fro m the “Available ports” list, then click on the  [Next] button. 
(6)  On the screen listing “Manufacturers and Printers”, click on the  [Have Disk…] button. The “Install 
From Disk” dialog box is displayed. 
(7)  Specify the “\ driver\WinNT4” folder in the CD-ROM drive, then click on the  [OK] button. 
 
 
 
(8)  Select the printer to be installed from “Printers” list, then click on the  [Next] button. 
(9)  The screen to select the existing installed printer  driver or use the new one, is displayed.  Select 
“Replace existing driver”, then click on the  [Next] button.  If you install the printer driver for the first 
time, this screen is not displayed. 
(10) Change the printer name if necessary, and select  whether or not you use the printer as the default 
printer (“Yes” or “No”).  Click on the  [Next] button. 
(11) Select whether or not the printer will be shared  with other network users (“Shared” or “Not shared”).  
Click on the  [Next] button. 
(12) Select whether or not the test page will  be printed (“Yes” or “No”), then click on the  [Finish] button. 
(13) The printer driver is installed.  When installa tion is completed, the new printer icon is added in the 
“Printers” folder. 
Windows NT4.0 
NOTE : 
The latest printer driver is available from the web site, “ the Barcode Master”. 
(http://barcode.toshibatec.co.jp/Eng/index.html)  
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-34 
 
(1)  Log on to your host computer as a member who has full control access privilege concerning the  printer settings. 
(2)  Select “Settings” – “Printers” from the  “Start” menu to open the printer folder. 
(3)  Double-click on the “Add Printer” icon.   The Add Printer Wizard runs.  Click on the [Next] button. 
(4)  Select “Local printer”.  Mark off the “Automati cally detect and install my Plug and Play printer” 
checkbox, then click on the  [Next] button. 
(5)  Select the port to be used for printing fro m the “Available ports” list, then click on the  [Next] button. 
(6)  On the screen listing “Manufacturers and Printers”, click on the  [Have Disk…] button.  The “Install 
From Disk” dialog box is displayed. 
(7)  Specify the “ \driver\WinXP-2000 ” folder in the CD-ROM drive, then click on the  [OK] button. 
 
 
 
(8)  Select the printer to be installed from “Printers” list, then click on the  [Next] button. 
(9)  The “Use Existing Driver” screen is displayed.   Select “Replace existing driver”, then click on the 
[Next]  button.  If you install the printer driver for  the first time, this screen is not displayed. 
(10) Change the printer name if necessary, and select  whether or not you use the printer as the default 
printer (“Yes” or “No”).  Click on the  [Next] button. 
(11) Select whether or not the printer will be shared  with other network users (“Shared” or “Not shared”).  
Click on the  [Next] button. 
(12) Select whether or not the test page will  be printed (“Yes” or “No”), then click on the  [Finish] button. 
(13) If the “Digital Signature Not Found” screen is displayed, click on the  [Yes] button. 
(14) When the “Completing the Add Printer  Wizard” screen is displayed, click on the [Finish] button. 
(15) When installation is completed, the new  printer icon is added in the “Printers” folder. 
Windows 2000/XP
NOTE: 
The latest printer driver is available from the web site, “ the Barcode Master”. 
(http://barcode.toshibatec.co.jp/Eng/index.html)  
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-35 
(2)  USB INTERFACE 
Installation starts by the operating system’s plug-and-play function.   
Windows 95 and Windows NT4.0 do not support the USB interface. 
 
 
 
(1)  Turn the printer ON, then connect it to  your host computer with the USB cable.   
  The “New Hardware Found” dialog box is di splayed, and “USB Device” is detected. 
  
 
(2)  After a while, the “Add New Hardware Wizard” dialog box is display\
ed. 
  Select “Specify the location of the driver (Advanced)”, then click on the  [Next]  button. 
  
Windows 98/Me  
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-36 
(3)  Select “Search for the best driver for your device. (Recommended)”. 
  Mark the “Specify a location” checkbox, then click on the  [Browse] button. 
 Specify “\ driver\WinMe-9x ” folder, then click on the  [Next] button. 
  
 
(4)  Check to see that the “USB Printing Suppor t” driver is detected, then click on the [Next] button. 
    
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-37 
(5)  When the screen which indicates the USB Prin ting Support driver has been installed, is 
displayed, click on the  [Finish] button. 
  
 
(6)  After a while, “ TEC B-SA4T” is detected as a new hardware. 
  
 
(7)  The “Add New Hardware Wizard” dialog box is displayed.    Select “Specify the location of the driver (Advanced)”, then click on the  [Next] button.