Toshiba Bsa4tp User Manual

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.7 Setting an Operating Environment
 
E2-18 
2.7.2 Parameter Setting  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
The Parameter Setting Mode contains  sub menus for selecting a language 
and setting the communication parameters.  Each time the  [PAUSE] key 
is pressed, the sub menus are displayed sequentially. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
 
 
 
Baud rate selection 
[PAUSE]
PARAMETER SET
SPEED 9600b
ps
PARAMETER SET
[PAUSE]
Data Length selection PARAMETER SET
DATA LENG. 8bits
[PAUSE]
Stop Bit selection PARAMETER SET
STOP BIT 1bit
[PAUSE]
Parity selection PARAMETER SET
PARITY EVEN
[PAUSE]
Flow Control selection PARAMETER SET
XON+READY AUTO
[PAUSE]
LCD Message Language selectionPARAMETER SET
LCD ENGLISH
[PAUSE]
ACK/BUSY timing selectionPARAMETER SET
ACK/BUSY TYPE1
[PAUSE]
WEB Printer Function selection PARAMETER SET
WEB PRINTER OFF
[PAUSE]
Plug & Play selection PARAMETER SET
PLUG & PLAY OFF
[PAUSE] 
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.7 Setting an Operating Environment
 
E2-19 
2.7.2 Parameter Setting  (Cont.) 
„ Serial (RS-232C) Interface  
 
  
Properties screen of Serial (COM) port 
under Windows98 
 
 
 
 
 
 
 
   
 
 
The following parameters of the RS-232C interface can be set: 
 Baud rate 
 Data length 
 Stop bit 
 Parity 
  Flow control  
 
Set these in accordance with the setting of your host computer. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
(1)  Baud Rate  
This parameter is to choose a communication speed of the RS-232C 
interface.  
As “9600 bps” has been chosen as defa
ult, change it in accordance with 
your PC.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
After making a choice, press the  [PAUSE] key.   
 
 
  
  
NOTES:  
1.  Choose a desired baud rate by  using the 
[RESTART] or 
[FEED] key.  
2.  Be careful if the printer is  turned off without pressing the 
[PAUSE]  key, the selected 
value does not become effective. PARAMETER SET 
SPEED   9600bps 
[RESTART]
[FEED]
SPEED  19200 bps 
SPEED   9600 bps 
SPEED   4800 bps 
SPEED   2400 bps 
SPEED  115200 bps 
SPEED  38400 bps  
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.7 Setting an Operating Environment
 
E2-20 
2.7.2 Parameter Setting  (Cont.) 
„ Serial (RS-232C) Interface  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
   
 
 
(2) Data Length 
This parameter is to choose a data
 length of the RS-232C interface. 
As “8 bits” has been chosen as defau lt, change it in accordance with your 
PC. 
 
 
 
 
 
 
 
 
After making a choice, press the  [PAUSE] key.   
 
 
(3) Stop Bit 
This parameter is to choose a stop bit of the RS-232C interface. 
As “1 bit” has been chosen as defa ult, change it in accordance with your 
PC.  
 
 
 
 
 
 
 
 
After making a choice, press the  [PAUSE] key. 
 
(4) Parity 
This parameter is to choose a parity of the RS-232C interface. 
As “None” has been chosen as default,  change it in accordance with your 
PC.  
 
 
 
 
 
 
 
 
 
After making a choice, press the  [PAUSE] key. 
 
 
 
PARAMETER SET 
PARITY     NONE 
PARITY     EVEN 
PARITY     ODD 
[RESTART]
[FEED]
PARITY     NONE 
PARAMETER SET 
DATA LENG. 8bits 
DATA LENG. 8bits 
DATA LENG. 7bits 
[RESTART]
[FEED]
PARAMETER SET 
STOP BIT  1bit 
STOP BIT  1bit 
STOP BIT  2bits 
[RESTART]
[FEED] 
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.7 Setting an Operating Environment
 
E2-21 
2.7.2 Parameter Setting  (Cont.) 
„ Serial (RS-232C) Interface  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
„  LCD Message Language   
 
 
(5) Flow Control 
This parameter is to choose a flow control of the RS-232C interface. 
As “XON+READ AUTO” has been c
hosen as default, change it in 
accordance with your PC.  
 
 
 
 
 
 
 
 
 
 
 
 
  XON/XOFF AUTO:  XON/XOFF mode  (Software Flow Control) 
XON+READY AUTO:  XON/XOFF + READY/BUSY (DTR) mode   (Software & DTR/DSR Hardware Flow 
Control) 
READY/BUSY:  READY/BUSY (DTR) mode 
  (DTR/DSR Hardware Flow Control) 
XON/XOFF:  XON/XOFF mode (Software Flow Control) 
READY/BUSY RTS:  RTS mode (CTS/RTS Hardware Flow  Control) 
 
After making a choice, press the  [PAUSE] key. 
 
 
 
This parameter is to choose a language of the LCD Message Display. 
As “ENGLISH” has been chosen as  default, change it as you like.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
After making a choice, press the  [PAUSE] key. 
 
NOTES: 
1.  When using the hardware flow  control, the control signals and 
data must be in pairs between 
the printer and the PC.  
 
Printer Host
 
TD 
→ RD 
RD 
←- TD 
RTS 
→ CTS 
CTS 
←- RTS 
DSR 
→ DTR 
DTR 
←- DSR 
 
Refer to the RS-232C 
connector’s pin layout in 
APPENDIX 2 . Check if the 
printer and the PC is properly 
connectable with your cable 
2.   Be careful that there are two  types of RS-232C cable; straight 
cable and cross cable. 
Use a straight cable for this 
printer.  
[RESTART]
[FEED]
XON+READY AUTO 
XON/XOFF AUTO 
READY/BUSY 
XON/XOFF 
READY/BUSY RTS 
PARAMETER SET 
XON+READY AUTO 
PARAMETER SET 
LCD   ENGLISH 
[RESTART]
[FEED]
ENGLISH 
ITALIAN  
JAPANESE 
SPANISH 
DUTCH 
FRENCH 
GERMAN  
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.7 Setting an Operating Environment
 
E2-22 
2.7.2 Parameter Setting  (Cont.) 
„ Parallel (Centronics) Interface  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
„  Web Printer Function when 
using TCP/IP (LAN)
 
 
 
 
 
This parameter is to choose an  ACK/BUSY timing of the parallel 
interface. 
“TYPE1” has been chosen as default,  but if a communication error occurs 
or a communication is not properly made, change to “TYPE2”.  
 
 
 
 
 
 
 
 
 
After making a choice, press the  [PAUSE] key. 
 
 
 
This parameter is to enable or disab le the web printer function which is 
available when the printer and your host computer is connected through 
TCP/IP. 
As “OFF” has been chosen as default,  change to “ON” when this function 
is used.  
 
 
 
 
 
 
 
 
After making a choice, press the  [PAUSE] key. 
 
 
NOTE: 
To enable this function, an IP 
address needs to be set, also. Refer 
to  Section 2.7.3 IP Address Setting 
(TCP/IP) .  
PARAMETER SET 
ACK/BUSY TYPE1 
ACK/BUSY TYPE1 
ACK/BUSY TYPE2 
[RESTART]
[FEED]
PARAMETER SET 
WEB PRINTER  OFF 
WEB PRINTER  OFF 
WEB PRINTER  ON 
[RESTART]
[FEED] 
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.7 Setting an Operating Environment
 
E2-23 
2.7.2 Parameter Setting  (Cont.) 
„ Plug & Play  
 
 
 
   
 
 
This parameter is to enable or disable the plug & play function. 
As “OFF” has been chosen as default,
 change it when this function is 
used.  
If the printer and the PC are connected by USB, plug & play will be 
automatically enabled, regardless of the setting of this parameter.  
 
 
 
 
 
 
 
 
 
After making a choice, press the  [PAUSE] key. 
 
 
 
PARAMETER SET 
PLUG & PLAY   OFF 
PLUG & PLAY   OFF 
PLUG & PLAY   ON 
[RESTART]
[FEED] 
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.7 Setting an Operating Environment
 
E2-24 
2.7.3  IP Address Setting  (TCP/IP) 
 
 
 
 
 
  When the printer is connected to a PC through TCP/IP by using a LAN 
cable, it is necessary to set an IP address in the System Mode for system 
administrators.  
 
The System Mode for system administrators consists of the following 
menus.  
 
 
 
 
 
 
DIAG.  Vx.x  This menu is used
 to check and print the printer 
system information and maintenance counter 
status.   
PARAMETER SET
 
 
  This menu is used to set the printer parameters. 
ADJUST SET  This menu is used to make a fine adjustment of a  print start position, cut position, etc. 
 
 
TEST PRINT  This menu is used to perform print tests.   
 
 
SENSOR ADJ.  This menu is used  to check the sensor statuses 
and adjust each sensor. 
 
 
RAM CLEAR  This menu is used to perform a RAM clear.   DO NOT USE this menu. 
 
 
IP ADDRESS  This menu is used to set an IP address.   
 
 
BASIC  This menu is used to  enable the printer to use 
Basic program. 
 
 
FOR FACTORY  This menu is intended for an in-process  inspection.  Do not use this menu.  
 
 
 
 
 
[FEED] 
[FEED] 
[FEED] 
[FEED] 
[FEED] 
[FEED] 
[FEED] 
[RESTART]
[RESTART] 
[RESTART] 
[RESTART]
[RESTART] 
[RESTART]
[RESTART] 
[RESTART] 
DIAG.  Vx.x 
PARAMETER SET
ADJUST SET 
TEST PRINT 
SENSOR ADJ. 
RAM CLEAR 
IP ADDRESS 
BASIC 
[FEED] 
FOR FACTORY 
[RESTART]
[FEED] 
Power OFF 
While holding down the  [FEED] and 
[PAUSE]  keys, turn on the printer.  
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.7 Setting an Operating Environment
 
E2-25 
2.7.3  IP Address Setting  (TCP/IP) (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  In this section, how to set the IP address is described. 
First, you need to access the System Mode for system administrators. 
 
 
 
 
 
 
 
 
 
 
 
1.
 While holding down the  [FEED] and [PAUSE]  keys, turn on the 
printer. 
 
 
 
 
 
 
2.  When “RESET” appears on the LCD Message Display, release 
the  [FEED]  and [PAUSE]  keys. 
 
  Now, the printer is in the System  Mode for system administrators. 
 
 
3.  Press  the  [FEED] or [RESTART]  key until “IP ADDRESS” 
appears on the LCD Message Display.  
 
 
 
 
 
 
 
 
 
 
 
 
 
4.  Press the  [PAUSE] key to enter the IP Address Setting Mode. 
 
 
 
F P
R 
DIAG. 
F  
 
IP ADDRESS 
 P 
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.7 Setting an Operating Environment
 
E2-26 
2.7.3  IP Address Setting  (TCP/IP) (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  The IP Address Setting Mode contains the following sub menus.  To 
enter each sub menu, press the 
[PAUSE] key. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
(1)  Printer IP Address  
This parameter is to set an IP address. 
 
 
 IP ADDRESS 
PRINTER IP ADRES 
IP ADDRESS 
GATEWAY IP ADRES
 
IP ADDRESS 
SUBNET MASK
 
IP ADDRESS 
SOCKET PORT
 
IP ADDRESS 
DHCP
 
[RESTART][FEED] 
[RESTART][FEED] 
[RESTART][FEED] 
[RESTART][FEED] 
[RESTART][FEED] 
IP ADDRESS 
DHCP CLIENT ID
 
[RESTART][FEED] 
IP ADDRESS 
PRINTER IP ADRES
 
IP ADDRESS 
192
 . 168 . 010 . 020 
IP ADDRESS 
192 .  168
 . 010 . 020 
IP ADDRESS 
192 . 168 .  010
 . 020 
IP ADDRESS 
192 . 168 . 010 .  020
 
[PAUSE]
[PAUSE]
[PAUSE]
IP ADDRESS 
GATEWAY IP ADRES
 
[PAUSE]
[PAUSE]
NOTES: 
1.  Set each 3-digit value by using  the 
[RESTART] or [FEED] key. 
 
[RESTART] key: Increment 
 
[FEED] key: Decrement 
  Range: 0 to 255 
2. Press the  [PAUSE] key to move 
the cursor to the next 3-digit 
value. 
3.  After the last 3-digit value is set,  press the 
[PAUSE] key to go to 
Gateway IP Address Setting.   
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.7 Setting an Operating Environment
 
E2-27 
2.7.3  IP Address Setting  (TCP/IP) (Cont.) 
 
  (2)  Gateway IP Address  
This parameter is to set a Gateway IP address. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
(3)  Subnet Mask  
This parameter is to set a Subnet Mask. 
 
 
IP ADDRESS 
SUBNET MASK
 
IP ADDRESS 
255 . 255 . 255 . 000
 
IP ADDRESS 
255 . 255 . 255 . 000
 
IP ADDRESS 
255 . 255 . 255 . 000
 
IP ADDRESS 
255 . 255 . 255 . 000
 
[PAUSE]
[PAUSE]
[PAUSE]
IP ADDRESS 
SOCKET PORT
 
[PAUSE]
[PAUSE]
IP ADDRESS 
GATEWAY IP ADRES
 
IP ADDRESS 
192 . 168 . 010 . 020
 
IP ADDRESS 
192 . 168 . 010 . 020
 
IP ADDRESS 
192 . 168 . 010 . 020
 
IP ADDRESS 
192 . 168 . 010 . 020
 
[PAUSE]
[PAUSE]
[PAUSE]
IP ADDRESS 
SUBNET MASK
 
[PAUSE]
[PAUSE]
NOTE: 
After the last 3-digit value is set, 
press the [PAUSE] key to go to 
Subnet Mask Setting.  
NOTE: 
After the last 3-digit value is set, 
press the [PAUSE] key to go to 
Socket Port Setting.