Toshiba Bsa4tp User Manual

2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.10 Position and Print Tone Fine Adjustment
 
E2-58 
2.10  Position and Print  Tone Fine 
Adjustment (Cont.) 
 
 
 
 
 
   
 
When the ribbon is slack or wrinkled a nd printing is affected, fine adjust 
the ribbon motor torque by using the following procedure. 
 
 
Take-up Motor (RBN ADJ ) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
After selecting a fine adjustment valu e or to skip this menu, press the 
[PAUSE]  key. 
 
 
 
 
Feed Motor (RBN ADJ )...

2.PRINTER SETUP ENGLISH VERSION EO1-33048 2.11 Threshold Setting
 
E2-59 
2.11 Threshold Setting 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  To maintain a constant print position 
the printer uses the media sensor to 
detect a print start position according to the difference of voltage between 
a print area and a gap or black mark.  When the media is pre-printed, the 
darker (or more dense) inks can inte rfere with this process causing paper 
jam errors. 
To get around this problem, first, try an...

2.PRINTER SETUP ENGLISH VERSION EO1-33048 2.11 Threshold Setting
 
E2-60 
2.11 Threshold Setting  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  7.
  Select the sensor to be adjusted by using the  [FEED] key. 
 
 
 
 
 
 
8.   Press and hold the  [PAUSE] key until more than 1.5 labels (tags) 
have been issued.   
  The media will continue to be fed until the  [PAUSE] key is released.  
(An automatic threshold setting for the selected sensor is completed 
by this operation.) 
 
 
 
 
 
 
 
 
9.  Press the...

2.PRINTER SETUP ENGLISH VERSION EO1-33048 2.11 Threshold Setting
 
E2-61 
2.11 Threshold Setting  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
   
 
 
If a paper jam error still occurs even 
after an automatic threshold setting 
has been performed, manually set the threshold voltage.   
 
To make a threshold value manually set in this section effective, select 
the Transmissive Sensor (when us ing manual threshold value) or 
Reflective Sensor (when using manual  threshold value) within software...

2.PRINTER SETUP ENGLISH VERSION EO1-33048 2.11 Threshold Setting
 
E2-62 
2.11 Threshold Setting  (Cont.) 
 
   
The Sensor Adjustment Mode contains sub menus for displaying the 
current status of each sensor and for storing “media level” voltage and 
“no media level” voltage.  Each time the 
[PAUSE] key is pressed, the 
sub menus are displayed sequentially.  
 
 
 
Sensor Status Display: 
Temperatures being detected by the Print Head Thermistor and the 
Ambient Thermistor are displayed. 
Black Mark...

2.PRINTER SETUP ENGLISH VERSION EO1-33048 2.11 Threshold Setting
 
E2-63 
2.11 Threshold Setting  (Cont.) 
 
 
 
   
 
 
 
(3) Press and hold the  [RESTART] or [FEED]  key for about 3 seconds 
aligning a blank part of print area with the Black Mark Sensor. 
 
 
 
(4) When storing a “media level” volta ge is completed, an asterisk “*”is 
displayed on the right side of a voltage.  Press the  [PAUSE] key. 
 
(5) A real-time voltage being detected by the Feed Gap Sensor is  displayed.  
 
 
 
„   When using...

2.PRINTER SETUP ENGLISH VERSION EO1-33048 2.11 Threshold Setting
 
E2-64 
2.11 Threshold Setting  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
„ Storing a “No Media Level” Voltage  
The following is how to set a “No medi a level” voltage that is used to 
detect a paper end.   
If a “NO PAPER” is displayed even if the media has not run out yet, this 
voltage needs to be set again.  
 
(1) Remove any media from the Black Mark Sensor/Feed Gap Sensor.  
 
 
(2) A real-time voltages being...

2.PRINTER SETUP ENGLISH VERSION EO1-33048 2.11 Threshold Setting
 
E2-65 
2.11 Threshold Setting  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
  The Parameter Fine Adjustment Mode 
contains sub menus for adjusting a 
print start position, cut/strip positi on, print tone, etc., and setting a 
threshold.  For details, refer to  Section 2.10 Print Position and Print 
Tone Fine Adjustment .  
Each time the  [PAUSE] key is pressed, the sub menus are displayed 
sequentially.  
 
 
(3) While “ADJUST SET.” is displayed,...

3. ON LINE OPERATION ENGLISH VERSION EO1-33048 3.1 Operation Panel 
 
E3- 1 
3.  ON LINE OPERATION
 
 
 
 
3.1 Operation Panel 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
This chapter describes usage of the ke ys on the Operation Panel in On 
Line mode.  
When the printer is in On Line mode and connected to a host computer, 
the normal operation of printing im ages on labels or tags can be 
accomplished.  
 
 
The figure below illustrates the Operation Panel and key functions.  
 
 
 
 
 
The LCD...

3. ON LINE OPERATION ENGLISH VERSION EO1-33048 3.2 Operation
 
E3- 2 
3.2 Operation 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
3.3 Reset 
 
 
 
 
 
 
 
 
 
 
 
 
 When the printer is turned on, the  “ON LINE ” message appears on the 
LCD Message Display.  It is shown during standby or normal printing.  
 
1.   The printer is turned on, standing by, or printing. 
 
 
 
2.  If any error occurs during printing, an error message appears.  The 
printer stops printing automatically.  (The number on the...