Toshiba Bsa4tp User Manual

7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33048 7.1 Media
 
E7- 1 
7. SUPPLY SPECIFICATIONS 
7.1 Media 
Please make sure that the media being used is approve d by TOSHIBA TEC.  The warranty does not apply when a 
problem is caused by using media that is not approved by TOSHIBA TEC. 
For information regarding TOSHIBA TEC approved medi a, please contact a TOSHIBA TEC authorised service 
representative.  
 
7.1.1 Media Type 
Two types of media can be loaded for this thermal transfer  and direct thermal...

7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33048 7.1 Media
 
E7- 2 
 
  
 
 
 
 
 
 
 
 
 
 
 
 
7.1.2  Detection Area of  the Transmissive Sensor 
The Transmissive Sensor is movable from the centre to the left edge of media.   
The Transmissive Sensor detects a ga p between labels, as illustrated below. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
NOTES: 
1.  To ensure print quality and print head life use only TOSHIBA TEC specifi\
ed media. 
2.  The ratio of a label length to a gap length must be a minimum of 3 to...

7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33048 7.1 Media
 
E7- 3 
7.1.3  Detection Area of  the Reflective Sensor 
The Reflective Sensor is movable from the centre to the left edge of media. 
The reflection factor of the Black Mark must be  10% or lower with a waveform length of 950 nm. 
The Reflective Sensor should be aligned with the centre of the Black Mar\
k.   
 
 
 
 
 
 
 
7.1.4  Effective Print Area 
The figure below illustrates the relation between th e head effective print width and media...

7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33048 7.2 Ribbon
 
E7- 4 
7.2 Ribbon 
 
Please make sure that the ribbon being used is approved  by TOSHIBA TEC.  The warranty does not apply to any 
problem caused by using non-approved ribbons. 
For information regarding TOSHIBA TEC appr oved ribbon, please contact a TOSHIBA TEC service 
representative.  
Type Spool type 
Width  60 – 110 mm  Recommended width is 60, 90, and 110 mm. 
Length  450 m (within  ∅75 mm) 
Outside Diameter  ∅75 mm (max.) 
 
The...

7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33048 
7.4 Care/Handling of Media and Ribbon
 
E7- 5 
7.3  Recommended Media and Ribbon Types (Cont.) 
Ribbon type  Description 
Vellum wax ribbon  This ribbon is mainly used fo r vellum paper and labels.  It has a very 
high ink density to cope with uneven printing surface 
Standard wax ribbon  Good match for coated  paper (Matt coat and glossy coat). 
Smear-less ribbon (Wax resin ribbon)  Good match for coated paper.  The printed image will resist water and...

APPENDIX 1  MESSAGES AND LEDS ENGLISH VERSION EO1-33048 
APPENDIX 1  MESSAGES AND LEDS
 
EA1- 1 
APPENDIX 1  MESSAGES AND LEDS 
Appendix 1 describes the LCD messages displayed on the operation panel.   
Symbols in the message 
1:  : The LED is illuminated.   ~: The LED is flashing.   z: The LED is unlit. 
2:  ****:  the number of unprinted media.  Up to 9999 (in pieces) 
3:  ###:  Flash memory card remaining memory for PC save area: 0 to 895 (in K bytes) 
4:  &&&&:  Remaining flash memory capacity for...

APPENDIX 1  MESSAGES AND LEDS ENGLISH VERSION EO1-33048 
APPENDIX 1  MESSAGES AND LEDS
 
EA1- 2 
 
LED IndicationNo. LCD Message ONLINE ERROR Printer Status 
Restoration by 
RESTART key
(Yes/No)  Acceptance of 
Status Request 
Reset Command 
(Yes/No) 
21 SYSTEM ERROR z   When the following abnormal operations are 
performed, a system error occurs: 
(a) Command fetch from an odd address 
(b) Access to word data at an odd address 
(c) Access to long-word data at an odd  address 
(d) Access to the area of...

APPENDIX 1  MESSAGES AND LEDS ENGLISH VERSION EO1-33048 
APPENDIX 1  MESSAGES AND LEDS
 
EA1- 3 
 
NOTE: Description of Command Error 
•  If a command error is found in a command received, 16 by tes of the command error, starting from the command 
code, will be displayed.  (However, [LF] and [NUL] will not be displayed.) 
 
Example 1 
[ESC] T20 G
30 [LF] [NUL]  
 Command error 
The following message appears. 
 
 
 
Example 2 
[ESC] XR; 0200, 0300, 0450, 1200, 1
, [LF] [NUL]  
 Command error 
The...

APPENDIX 2  INTERFACE ENGLISH VERSION EO1-33048 APPENDIX 2  INTERFACE
 
EA2- 1 
APPENDIX 2  INTERFACE 
 
 
 
 
 
 
 
 
 
 
 

APPENDIX 2  INTERFACE ENGLISH VERSION EO1-33048 APPENDIX 2  INTERFACE
 
EA2- 2 
Connector: 
Signal PIN  No.  SPP Mode  Nibble Mode 
1 nStrobe  HostClk 
2  Data 1  Data 1 
3  Data 2  Data 2 
4  Data 3  Data 3 
5  Data 4  Data 4 
6  Data 5  Data 5 
7  Data 6  Data 6 
8  Data 7  Data 7 
9  Data 8  Data 8 
10 nAck  PtrClk 
11 Busy  PtrBusy 
12 PError  AckDataReq 
13 Select  Xflag 
14 nAutoFd  HostBusy 
15 NC  NC 
16 0V  0V 
17  CHASSIS GND  CHASSIS GND 
18  +5V (For detection)  +5V (For detection) 
19...