Toshiba B Sa4t G Manual

 
- 48 -  
              
< 1 > D I A G .       V 1 . 2 A
T Y P E    [ S ] N O    C U T(17)  Issue type setting mode 
              
        [PAUSE] 
 
(18)  Press the [PAUSE] key. 
< 1 > D I A G .       V 1 . 2 A
A U T O    D I A G N O S T I C(19)  Automatic self-test mode 
              
        [PAUSE] 
 
(20)  Press the [PAUSE] key. 
< 1 > D I A G .       V 1 . 2 A
C H E C K I N G   &    P R I N T(21)  Start of automatic self-test 
 
             (22)  The results are printed out. 
         
 
 
< 1...

 
- 49 - (2)  Head broken dots check 
 
     Power OFF 
  (1)  Power off state 
             
        [FEED] [PAUSE] (2)  While holding the [FEED] and [PAUSE] keys 
down, turn the power on. 
 
< 1 > D I A G .       V 1 . 2 A(3)  The self-test menu is displayed. 
              
              
        [PAUSE] 
 
(4)  Press the [PAUSE] key. 
< 1 > D I A G .       V 1 . 2 A
P R T    T Y P E   T R A N S F R(5)  Print type setting mode 
              
        [PAUSE] 
 
(6)  Press the [PAUSE] key. 
< 1 > D I A...

 
- 50 -  
              
< 1 > D I A G .       V 1 . 2 A
C H E C K I N G          (15)  Start of head broken dots check 
              
        [When a broken dot error is not found] 
< 1 > D I A G .       V 1 . 2 A
N O R M A L    E N D       (16)  The results are displayed. (Normal end) 
              
        [PAUSE] 
 
(17)  Press the [PAUSE] key. 
< 1 > D I A G .       V 1 . 2 A
             (18)  The self-test menu is displayed. 
              
 
 
 [When a broken 
dot error is found] 
       
< 1...

 
- 51 - 6.2.2 Self-test Items 
(1)  Printing of maintenance counter values and various parameter values 
 c  Maintenance counter values 
    •  Total label distance covered (cannot be cleared) 
    •  Label distance covered 
  • Print distance 
  • Cut count 
    •  Ribbon motor drive time 
    •  RS-232C hardware error count 
    •  System error count 
    •  Momentary power interruption count 
 d  Various parameter values 
    [Value programmed on the PC] 
    •  Feed amount fine adjustment value...

 
- 52 -   • Keyboard I/F 
  • Automatic calibration 
  • LAN enable/disable 
  • IP address  
  • MAC address 
  • BASIC  
    •  Socket communication port number   
  • BASIC interpreter 
  • DHCP  
    •  RFID module type 
    •  RFID tag type 
    •  RFID module’s destination code setting    (Supported from C2.0C) 
    •  RFID error tag detection 
    •  Password to protect error tag detection 
    •  Automatic unlock function setting 
    •  Maximum number of issue retries 
    •  Maximum number of...

 
- 53 - (2) Automatic self-test 
 c Memory check 
    •  Program area (Model, creation date, version, part number, checksum) 
    •  Boot area (Model, creation date, version, checksum) 
    •  HTML area (Model, creation date, version, checksum) 
    •  Font area checksum 
    •  Bit map Kanji ROM checksum (Gothic, Mincho, Chinese Kanji) 
  • EEPROM check 
  • RAM check 
 d Sensor check 
  • Strip sensor 
    •  Thermal head open sensor 
    •  Front cover open sensor 
    •  Cutter home position sensor...

 
- 54 - Print Samples of Self-test Result   
(1)  Maintenance counter values and various parameter values 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 TOTAL FEED   1.1km               [QM] 
 FEED       1.1km    
 PRINT    0.5km    
 CUT       96       
 RIBBON   3h       
 232C ERR   255      
 SYSTEM ERR   0        
 POWER FAIL   0        
 [PC]                   [KEY] 
 FEED   +2.0mm   FEED    +0.0mm 
 CUT     +0.0mm    CUT    +1.0mm 
 BACK    +0.0mm     BACK    +0.0mm 
 TONE(T)  +0step...

 
- 55 -  
(2) Automatic self-test  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 NOTES:  1. Print conditions: Label length of 122mm, thermal transfer/direct thermal print 
mode
(*1), no sensors used, 4 ips, one-label issue, batch 
issue 
          (*1)  Depends on the ribbon setting. 
2.    “°” used for “°C” may not be printed correctly, depending on the type of the 
character code selected. 
3.  In the case the printer firmware version is C1.9A or greater, a BASIC program 
file name and system mode program file...

 
- 56 - 6.2.2.1  Details of Self-test Result 
(1)  Maintenance counter values 
Item Description  Range 
TOTAL FEED  Total label distance covered 
(cannot be cleared) 0.0 to 3200.0 km 
FEED  Label distance covered  0.0 to 3200.0 km 
PRINT  Print distance  0.0 to 200.0 km 
CUT  Cut count  0 to 1000000 
RIBBON  Ribbon motor drive time  0 to 2000 hours 
232C ERR  RS-232C hardware error count  0 to 255 
SYSTEM ERR  System error count  0 to 15 
POWER FAIL  Momentary power interruption count  0 to 15 
RFID WT...

 
- 57 - Maintenance Counter  Count Conditions 
Momentary power interruption 
count Counts when a momentary power interruption occurs. 
The number of times a tag 
data write succeeded. Counts the number of times a tag data write succeeded. 
The number of times a tag 
data write failed. Counts the number of times a tag data write failed. 
 
 
(2)  Various parameters values 
 
Item Description  Specification 
[PC] FEED Feed amount fine adjustment  -50.0 mm to +50.0 mm (See NOTE.)
 CUT Cut (strip) position...