Toshiba B Sa4t G Manual

 
- 38 -
5.16  Z-MODE SETTING (SUPPORTED FROM C1.9A) 
5.16.1  Outline of the Z-Mode 
The Z-Mode is a feature intended for enabling much easier start-up of the BASIC program.    Although 
the Z-Mode is similar to the BASIC setting menu, it contains only two functions: Enabling or disabling the 
BASIC program and starting the BASIC system mode program.     
The display and the procedure are different, but “Z-MODE ON” equals to “BASIC ON” and they are 
linked with each other.   
 
 
5.16.2  Operation...

 
- 39 -
(Display of the BASIC system mode program)
             (15)  The BASIC system mode program is started if 
it has been downloaded.    The display 
depends on the program. 
         
 (16) The BASIC system mode program exits.   
(How to exit the program is depending on the 
BASIC system mode program in use.) 
< 1 0 > Z - M O D E       
             (17) Z-Mode setting menu display 
 
 
Z-Mode Setting 
 
 
Z-MODE 
OFF 
Z-MODE 
ON  SETTING  OFF 
OFF: Disabled. 
ON    SETTING OFF:  Z-Mode is...

 
- 40 -
5.17  LCD MESSAGES AND LED INDICATIONS 
The model, the print head type, and firmware versi on are displayed on the lower line of the LCD. 
 
No.  LCD Messages on   
Upper line 
(English)  LED Indication
 
Printer Status 
Recoverable  by the 
[RESTART]  key  
Yes/No  Acceptance 
of Status 
Request and  Reset 
Commands Yes/No
 
ON LINE  ERROR
1  ON LINE 
{  zOnline mode - Yes 
 ON LINE 
  z Online mode 
(Communicating) - Yes 
2  HEAD OPEN 
z  zThe head was opened in online mode. - Yes 
3 PAUSE...

 
- 41 -
 
No.  LCD Messages on   
Upper line 
(English)  LED Indication
 
Printer Status 
Recoverable  by the 
[RESTART]  key  
Yes/No  Acceptance 
of Status 
Request and  Reset 
Commands Yes/No
 
ON LINE  ERROR
20  EEPROM ERROR 
z  { Data cannot be read from/written to a 
backup EEPROM properly. No No 
21  SYSTEM ERROR 
z  { When the following abnormal 
operations are performed, a system 
error occurs: 
(a)  Command fetch from an odd 
address 
(b)  Access to word data at an odd  address 
(c)  Access...

 
- 42 -
NOTE 1:
  When a command produces an error, 16 byte s of the command code of the erroneous 
command are displayed on the upper line of the LCD.    (However, [LF] and [NUL] are not displayed.) 
  [Example 1]  [ESC] PC001; 0A00, 0300, 2, 2, A, 00, B [LF] [NUL] 
    Command error 
LCD display 
PC001;0A00,0300,
B-SA4T-T   V1.2A 
  [Example 2]  [ESC] T20 G30 [LF] [NUL] 
   Command error 
LCD display 
T20G30 
B-SA4T-T   V1.2A 
  [Example 3]  [ESC] XR; 0200, 0300, 0450, 1200, 1 [LF] [NUL] 
    Command...

 
- 43 -
5.18  LCD MESSAGES IN DIFFERENT  LANGUAGES (UPPER LINE ON LCD) 
No. ENGLISH  No. GERMAN  No. FRENCH 
1 ON LINE   1ON LINE 1PRETE 
2 HEAD OPEN   2KOPF OFFEN 2TETE OUVERTE 
3 PAUSE       ****   3PAUSE       **** 3PAUSE       ****
4 COMMS ERROR  4UEBERTR.-FEHLER 4ERR. COMMUNICAT.
5 PAPER  JAM   ****   5PAPIERSTAU  **** 5PB.  PAPIER  ****
6 CUTTER ERROR****   6MESSERFEHL.**** 6PB.  CUTTER  ****
7 NO  PAPER    ****   7PAPIERENDE  **** 7FIN  PAPIER  ****
8 HEAD  OPEN   ****   8KOPF  OFFEN  **** 8TETE...

 
- 44 -
 
No.  DUTCH   No. SPANISH   No. JAPANESE 
1  IN LIJN   1ON LINE 1
2 KOP OPEN   2CABEZAL ABIERTO 2
3 PAUZE       ****   3PAUSA       **** 3
4 COMM.  FOUT   4ERROR COMUNICACI 4
5 PAPIER VAST ****   5ATASCO PAPEL**** 5
6 SNIJMES FOUT****   6ERROR CORTAD**** 6
7 PAPIER  OP   ****   7SIN  PAPEL   ****7
8 KOP  OPEN    ****   8CABEZA ABIER**** 8
9 PRINTKOP DEFECT   9ERROR DE CABEZAL 9
10 TEMP. FOUT   10TEMP.CABEZA ALTA 10
11 LINT  FOUT   ****   11ERROR CINTA **** 11
12 DEUR  OPEN   ****   12TAPA...

 
- 45 -
6. SYSTEM MODE 
6.1  OUTLINE OF SYSTEM MODE 
In this mode, self-test and parameter settings are performed.    Described below is the key operation 
procedure in system mode. 
zSystem mode for service persons and system administrators (All menu items are available.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
While holding the [FEED] and [PAUSE] keys down, turn the power on. 
Printing of maintenance counter values and various parameter 
values  
Printer self-test operation and printing of...

 
- 46 -  
 
 
 
 
 
 
 
zSystem mode for users (Available menu items are limited.) 
 
While holding the [FEED] and [RESTART] keys down, turn the power on. 
Printing of maintenance counter values and various parameter 
values 
Printer self-test operation and printing of results   
Feed amount fine adjustment, Cut (strip) position fine adjustment, 
Reverse feed amount fine adjustment, X-coordinate fine 
adjustment, Print tone fine adjustment (Thermal transfer/Direct 
thermal print mode), Ribbon motor...

 
- 47 -
6.2 SELF-TEST 
6.2.1  Self-test Operation Example 
(1)  Printing of maintenance counter values, various parameter values, and automatic self-test 
result 
 
     Power OFF 
  (1)  Power off state 
             
        [FEED] [PAUSE] (2)  While holding the [FEED] and [PAUSE] keys 
down, turn the power on. 
 
< 1 > D I A G .       V 1 . 2 A(3)  The self-test menu is displayed. 
              
              
        [PAUSE] 
 
(4)  Press the [PAUSE] key. 
< 1 > D I A G .       V 1 . 2 A
P R T    T...