Toshiba B Sa4t G Manual

 
- 18 - (19)  Ribbon near end detection (RBN NEAR END) 
  •  OFF:  A ribbon near end state is not detected. 
  • 30 m:  A ribbon near end state is detected when the remaining ribbon length is 
approximately 30 m. 
  • 70 m:  A ribbon near end state is detected when the remaining ribbon length is 
approximately 70 m. 
(20)  Expansion I/O operation mode (EX. I/O) 
 • TYPE1: Standard mode 
 • TYPE2: In-line mode 
(21)  Plug-and-play operation (PLUG & PLAY) 
  •  ON:  A plug-and-play operation is performed....

 
- 19 -
5.9  FINE ADJUSTMENT VALUE SETTING 
5.9.1  Fine Adjustment Value Setting Operation Example 
     
Power ON    
              
O N  L I N E       (1) Idling 
B - S A 4 T - T       V 1 . 2 A 
              
        [PAUSE] 
 
(2)  Press the [PAUSE] key. 
P A U S E         (3)  “PAUSE” is displayed. 
B - S A 4 T - T       V 1 . 2 A 
              
        [RESTART] 
 
(4)  Hold down the [RESTART] key for 3 seconds 
or more while the printer is in a pause state. 
< 1 > R E S E T          (5)  The...

 
- 20 -  
              
< 3 > A D J U S T    S E T 
X    A D J U S T   + 5 0 . 0 m m(17)  X-coordinate fine adjustment: 
  Set a fine adjustment value using the [FEED] 
and [RESTART] keys. 
              
        [PAUSE] 
 
(18)  Press the [PAUSE] key. 
< 3 > A D J U S T    S E T 
T O N E    A D J . < T >      + 3
             (19)  Print tone fine adjustment   
(Thermal transfer print mode): 
  Set a fine adjustment value using the [FEED] 
and [RESTART] keys. 
        [PAUSE] 
 
(20)  Press the...

 
- 21 -  
              
< 1 > R E S E T          
             (35)  The reset menu is displayed. 
              
        [PAUSE] 
 
(36)  Press the [PAUSE] key. 
O N  L I N E       
B - S A 4 T - T       V 1 . 2 A(37)  The printer returns to the same state as when 
the power is turned off and on again.  

 
- 22 - 5.9.2  Fine Adjustment Value Setting Items   
For details, refer to the section, “6.4 VARIOUS FINE ADJUSTMENT VALUE SETTING”. 
(1)  Feed fine adjustment (FEED ADJ.) 
  -50.0 mm to +50.0 mm (in 0.1 mm units) 
(2)  Cut (strip) position fine adjustment (CUT ADJ.) 
  -50.0 mm to +50.0 mm (in 0.1 mm units) 
(3)  Back feed fine adjustment (BACK ADJ.) 
  -9.9 mm to +9.9 mm (in 0.1 mm units) 
(4)  X-coordinate fine adjustment (X ADJUST) 
  -99.9 mm to +99.9 mm (in 0.1 mm units) 
(5)  Print density fine...

 
- 23 -
5.10  DUMPING OF RECEIVE BUFFER 
5.10.1  Operation Example of Receive Buffer Dumping 
     
Power ON    
              
O N  L I N E       (1) Idling 
B - S A 4 T - T       V 1 . 2 A 
              
        [PAUSE] 
 
(2)  Press the [PAUSE] key. 
P A U S E         (3)  “PAUSE” is displayed. 
B - S A 4 T - T       V 1 . 2 A 
              
        [RESTART] 
 
(4)  Hold down the [RESTART] key for 3 seconds 
or more while the printer is in a pause state. 
< 1 > R E S E T          (5)  The reset...

 
- 24 -  
              
< 4 > D U M P    M O D E   
N O W    P R I N T I N G . . .(17)  Start of printing receive buffer data 
             (18)  166 lines of data are printed. 
              
< 4 > D U M P    M O D E   
P R I N T    O N   D E M A N D(19)  Print method setting: 
  Select a print method using the [FEED] and 
[RESTART] keys. 
              
        [RESTART] 
 
(20)  Press the [RESTART] key. 
< 4 > D U M P    M O D E   
P R I N T    A L L         (21)  Print method setting: 
  Select a...

 
- 25 - Data in the receive buffer is printed in the format below. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Feed  
direction 
 
 
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00    ................ 
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00    ................ 
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00    ................ 
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00    ................ 
7B 41 58 3B 2B 30 30 30 2C 2B 30 30 30 2C 2B 30   {AX;+000,+000,+0 
30 7C 7D 7B 44 30 37...

 
- 26 - Print conditions: 
•  Print width:  Approximately 100 mm 
• Sensor:  Not used 
•  Print speed:  4 ips   
•  A currently selected print mode (thermal transfer/direct thermal) is used. 
•  Data of 16 bytes is printed on one line. 
•  Data is printed, starting from new data to old data. 
•  Data pointed by a receive buffer write pointer is printed in bold type. 
 
Size of receive buffer 
RS-232C:  1 MB (Max. 65536 lines) 
Centronics:  1 MB (Max. 65536 lines) 
Network I/F:  1 MB (Max. 65536 lines)...

 
- 27 -
5.12  AUTOMATIC CALIBRATION SETTING   
5.12.1   Operation Example of Automatic Calibration Setting 
     
Power ON    
              
O N  L I N E       (1)  Idling or printing normally 
B - S A 4 T - T       V 1 . 2 A 
              
        [PAUSE] 
 
(2)  Press the [PAUSE] key. 
P A U S E         (3)  “PAUSE” is displayed. 
B - S A 4 T - T       V 1 . 2 A 
              
        [RESTART] 
 
(4)  Hold down the [RESTART] key for 3 seconds 
or more while the printer is in a pause state. 
< 1 >...