Toshiba B Sa4t G Manual

							 
- 18 - (19)  Ribbon near end detection (RBN NEAR END) 
  •  OFF:  A ribbon near end state is not detected. 
  • 30 m:  A ribbon near end state is detected when the remaining ribbon length is 
approximately 30 m. 
  • 70 m:  A ribbon near end state is detected when the remaining ribbon length is 
approximately 70 m. 
(20)  Expansion I/O operation mode (EX. I/O) 
 • TYPE1: Standard mode 
 • TYPE2: In-line mode 
(21)  Plug-and-play operation (PLUG & PLAY) 
  •  ON:  A plug-and-play operation is performed. 
  •  OFF:  A plug-and-play operation is performed. 
(22)  Label end/ribbon error process (LBL/RBN END) 
  • TYPE1:  When a label end or ribbon error state is detected, the printer stops even if it is 
printing. 
  • TYPE2:  When a label end or ribbon error state is detected, the printer prints the current 
label as far as possible, then stops. 
(23)  Pre-strip process (PRE PEEL OFF) 
  •  OFF:  A pre-strip operation is not performed. 
  •  ON:  A pre-strip operation is performed. 
NOTE:  When the pre-strip operation parameter is set to ON, a 6-mm forward feed is 
performed, then a 6-mm reverse feed before printing on the label starts.  The 
amount of feed can be finely adjusted. 
(24)  Reverse feed speed (BACK SPEED) 
 • STD:  3 ips 
 • LOW:  2 ips 
(25)  MaxiCode specification (MAXI CODE) 
  •  TYPE1:  Compatible with a current version 
 • TYPE2: Special specification 
(26)  Keyboard I/F (KB I/F) 
 • OFF:  (Disabled) 
  •  KB60(1):  KB-60 Old version 
  •  KB60(2):  KB-60 Current version 
 • KB80:  KB-80 
(27)  Strip motor torque (PEEL OFF TRQ) 
 • R0: Low 
 • R1:  ↑ 
 • R2:  ↓ 
 • R3: High 
(28)  Print head applied current table setting (TONE TABLE) 
 • TYPE1: Standard table 
  •  TYPE2:  Additional table 1 
(29)  High speed cut issue (CUT MODE) 
  •  TYPE1:  Normal cut issue 
  •  TYPE2:  High speed cut issue 
(30)  Multiple-label set issue (MULTI LABEL) 
  •  OFF:  Disabled (Normal operation) 
  •  ON:  Enabled (Multiple-label set issue) 
(31)  System mode password setting (PASSWORD) 
  •  OFF:  Password is not asked to enter the system mode. 
  •  ON:  Password is asked to enter the system mode.   
  
						

							 
- 19 -
5.9  FINE ADJUSTMENT VALUE SETTING 
5.9.1  Fine Adjustment Value Setting Operation Example 
     
Power ON    
              
O N  L I N E       (1) Idling 
B - S A 4 T - T       V 1 . 2 A 
              
        [PAUSE] 
 
(2)  Press the [PAUSE] key. 
P A U S E         (3)  “PAUSE” is displayed. 
B - S A 4 T - T       V 1 . 2 A 
              
        [RESTART] 
 
(4)  Hold down the [RESTART] key for 3 seconds 
or more while the printer is in a pause state. 
< 1 > R E S E T          (5)  The reset menu is displayed. 
              
              
        [FEED] 
 
(6)  Press the [FEED] key. 
< 2 > P A R A M E T E R    S E T
             (7)  System mode menu display 
(Parameter setting) 
              
        [FEED] 
 
(8)  Press the [FEED] key. 
< 3 > A D J U S T    S E T 
             (9)  System mode menu display 
(Fine adjustment value setting) 
              
        [PAUSE] 
 
(10)  Press the [PAUSE] key. 
< 3 > A D J U S T    S E T 
F E E D    A D J . + 1 0 . 0 m m
             (11)  Feed amount fine adjustment: 
  Set a fine adjustment value using the [FEED] 
and [RESTART] keys. 
        [PAUSE] 
 
(12)  Press the [PAUSE] key. 
< 3 > A D J U S T    S E T 
C U T    A D J .     + 5 . 0 m m
             (13)  Cut (strip) position fine adjustment: 
  Set a fine adjustment value using the [FEED] 
and [RESTART] keys. 
        [PAUSE] 
 
(14)  Press the [PAUSE] key. 
< 3 > A D J U S T    S E T 
B A C K    A D J .    - 3 . 0 m m
             (15)  Back feed amount fine adjustment: 
  Set a fine adjustment value using the [FEED] 
and [RESTART] keys. 
        [PAUSE] 
 
(16)  Press the [PAUSE] key. 
               
						

							 
- 20 -  
              
< 3 > A D J U S T    S E T 
X    A D J U S T   + 5 0 . 0 m m(17)  X-coordinate fine adjustment: 
  Set a fine adjustment value using the [FEED] 
and [RESTART] keys. 
              
        [PAUSE] 
 
(18)  Press the [PAUSE] key. 
< 3 > A D J U S T    S E T 
T O N E    A D J . < T >      + 3
             (19)  Print tone fine adjustment   
(Thermal transfer print mode): 
  Set a fine adjustment value using the [FEED] 
and [RESTART] keys. 
        [PAUSE] 
 
(20)  Press the [PAUSE] key. 
< 3 > A D J U S T    S E T 
T O N E    A D J . < D >      - 2
             (21)  Print tone fine adjustment   
(Direct thermal print mode): 
  Set a fine adjustment value using the [FEED] 
and [RESTART] keys. 
        [PAUSE] 
 
(22)  Press the [PAUSE] key. 
< 3 > A D J U S T    S E T 
R B N    A D J    < F W >    - 1 0
             (23)  Ribbon motor drive voltage fine adjustment 
(Take-up): 
  Set a fine adjustment value using the [FEED] 
and [RESTART] keys. 
        [PAUSE] 
 
(24)  Press the [PAUSE] key. 
< 3 > A D J U S T    S E T 
R B N    A D J    < B K >    - 5
             (25)  Ribbon motor drive voltage fine adjustment 
(Feed): 
  Set a fine adjustment value using the [FEED] 
and [RESTART] keys. 
        [PAUSE] 
 
(26)  Press the [PAUSE] key. 
< 3 > A D J U S T    S E T 
T H R E S H O L D < R > 1 . 0 V
             (27) Reflective sensor manual threshold fine 
adjustment: 
  Set a fine adjustment value using the [FEED] 
and [RESTART] keys. 
        [PAUSE] 
 
(28)  Press the [PAUSE] key. 
< 3 > A D J U S T    S E T 
T H R E S H O L D < T > 1 . 4 V
             (29) Transmissive sensor manual threshold fine 
adjustment: 
  Set a fine adjustment value using the [FEED] 
and [RESTART] keys. 
        [PAUSE] 
 
(30)  Press the [PAUSE] key. 
< 3 > A D J U S T    S E T 
             (31) The find adjustment value setting menu is 
displayed. 
              
        [RESTART] 
 
(32)  Press the [RESTART] key. 
< 2 > P A R A M E T E R    S E T
             (33)  The parameter setting menu is displayed. 
              
        [RESTART] 
 
(34)  Press the [RESTART] key. 
               
						

							 
- 21 -  
              
< 1 > R E S E T          
             (35)  The reset menu is displayed. 
              
        [PAUSE] 
 
(36)  Press the [PAUSE] key. 
O N  L I N E       
B - S A 4 T - T       V 1 . 2 A(37)  The printer returns to the same state as when 
the power is turned off and on again.  
						

							 
- 22 - 5.9.2  Fine Adjustment Value Setting Items   
For details, refer to the section, “6.4 VARIOUS FINE ADJUSTMENT VALUE SETTING”. 
(1)  Feed fine adjustment (FEED ADJ.) 
  -50.0 mm to +50.0 mm (in 0.1 mm units) 
(2)  Cut (strip) position fine adjustment (CUT ADJ.) 
  -50.0 mm to +50.0 mm (in 0.1 mm units) 
(3)  Back feed fine adjustment (BACK ADJ.) 
  -9.9 mm to +9.9 mm (in 0.1 mm units) 
(4)  X-coordinate fine adjustment (X ADJUST) 
  -99.9 mm to +99.9 mm (in 0.1 mm units) 
(5)  Print density fine adjustment (Thermal transfer print mode) (TONE ADJ.) 
  -10 step to +10 step (in units of 1 step) 
(6)  Print density fine adjustment (Direct thermal print mode) (TONE ADJ.) 
  -10 step to +10 step (in units of 1 step) 
(7)  Ribbon motor drive voltage fine adjustment (Take-up) (RBN ADJ ) 
  -15 step to +2 step (in units of 1 step) 
(8)  Ribbon motor drive voltage fine adjustment (Feed) (RBN ADJ ) 
  -15 step to +10 step (in units of 1 step) 
(9)  Reflective sensor manual threshold fine adjustment (THRESHOLD ) 
  0.0 V to 4.0 V 
(10)  Transmissive sensor manual threshold fine adjustment (THRESHOLD ) 
  0.0 V to 4.0 V 
 
 
 
 
 
 
  
						

							 
- 23 -
5.10  DUMPING OF RECEIVE BUFFER 
5.10.1  Operation Example of Receive Buffer Dumping 
     
Power ON    
              
O N  L I N E       (1) Idling 
B - S A 4 T - T       V 1 . 2 A 
              
        [PAUSE] 
 
(2)  Press the [PAUSE] key. 
P A U S E         (3)  “PAUSE” is displayed. 
B - S A 4 T - T       V 1 . 2 A 
              
        [RESTART] 
 
(4)  Hold down the [RESTART] key for 3 seconds 
or more while the printer is in a pause state. 
< 1 > R E S E T          (5)  The reset menu is displayed. 
              
              
        [FEED] 
 
(6)  Press the [FEED] key. 
< 2 > P A R A M E T E R    S E T
             (7)  System mode menu display 
(Parameter setting) 
              
        [FEED] 
 
(8)  Press the [FEED] key. 
< 3 > A D J U S T    S E T 
             (9)  System mode menu display 
(Fine adjustment value setting) 
              
        [FEED] 
 
(10)  Press the [FEED] key. 
< 4 > D U M P    M O D E   
             (11)  The receive buffer dumping menu is displayed.
              
        [PAUSE] 
 
(12)  Press the [PAUSE] key. 
< 4 > D U M P    M O D E   
B U F F E R        R S - 2 3 2 C(13)  Setting of receive buffer to be dumped: 
  Select a receive buffer to be dumped using the 
[FEED] and [RESTART] keys 
              
        [PAUSE] 
 
(14)  Press the [PAUSE] key. 
< 4 > D U M P    M O D E   
P R I N T    O N   D E M A N D(15)  Print method setting: 
  Select a print method using the [FEED] and 
[RESTART] keys. 
              
        [PAUSE] 
 
(16)  Press the [PAUSE] key.  
						

							 
- 24 -  
              
< 4 > D U M P    M O D E   
N O W    P R I N T I N G . . .(17)  Start of printing receive buffer data 
             (18)  166 lines of data are printed. 
              
< 4 > D U M P    M O D E   
P R I N T    O N   D E M A N D(19)  Print method setting: 
  Select a print method using the [FEED] and 
[RESTART] keys. 
              
        [RESTART] 
 
(20)  Press the [RESTART] key. 
< 4 > D U M P    M O D E   
P R I N T    A L L         (21)  Print method setting: 
  Select a print method using the [FEED] and 
[RESTART] keys. 
              
        [PAUSE] 
 
(22)  Press the [PAUSE] key. 
< 4 > D U M P    M O D E   
N O W    P R I N T I N G . . .(23)  Start of printing the remaining receive buffer 
data 
             (24)  All of the remaining data is printed. 
              
< 4 > D U M P    M O D E   
             (25)  After printing is completed, the display is 
returned to the receive buffer dumping menu. 
 
 
Receive buffer (BUFFER) 
 
•  RS-232C  RS-232C receive buffer 
•  CENTRO.  Centronics receive buffer 
•  NETWORK  Network I/F receive buffer 
•  BASIC1  Buffer between the BASIC interpreter I/F and the Interpreter 
•  BASIC2  Buffer between the BASIC interpreter and the printer 
•  USB  USB receive buffer 
•  RF-ID  RFID receive buffer 
 
Print method (PRINT) 
 
•  ON DEMAND  Prints 166 lines of data (approx. 50 cm), then stops. 
•  ALL  Prints all data in the receive buffer, then stops. 
  
 
FEED 
RESTART
FEED 
RESTART 
						

							 
- 25 - Data in the receive buffer is printed in the format below. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Feed  
direction 
 
 
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00    ................ 
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00    ................ 
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00    ................ 
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00    ................ 
7B 41 58 3B 2B 30 30 30 2C 2B 30 30 30 2C 2B 30   {AX;+000,+000,+0 
30 7C 7D 7B 44 30 37 37 30 2C 31 31 30 30 2C 30   0|}{D0760,1100,0 
37 34 30 7C 7D 7B 43 7C 7D 7B 4C 43 3B 30 30 33   740|}{C|}{LC;003 
30 2C 30 30 32 30 2C 30 30 33 30 2C 30 36 36 30   0,0020,0030,0660 
2C 30 2C 32 7C 7D 7B 4C 43 3B 30 30 37 30 2C 30   ,0,2|}{LC;0070,0 
30 32 30 2C 30 30 37 30 2C 30 36 36 30 2C 30 2C   020,0070,0660,0, 
39 7C 7D 7B 4C 43 3B 30 30 35 30 2C 30 30 32 30   9|}{LC;0050,0020 
 
 
44 45 46 47 48 49 4A 7C 7D 7B 50 43 31 30 3B 30   DEFGHIJ|}{PC10;0 
33 35 30 2C 30 34 30 30 2C 31 2C 31 2C 4B 2C 30   350,0400,1,1,K,0 
30 2C 42 3D 41 42 43 44 65 66 67 68 69 6A 6B 6C   0,B=ABCDefghijkl 
 
6D 6E 6F 70 7C 7D 7B 50 56 30 32 3B 30 33 33 30   mnop|}{PV02;0330 
2C 30 36 36 30 2C 30 32 37 30 2C 30 32 35 30 2C   ,0660,0270,0250, 
41 2C 30 30 2C 42 3D 42 7C 7D 7B 50 56 30 33 3B   A,00,B=B|}{PV03; 
 
 
3B 30 39 30 30 2C 30 31 38 30 2C 54 2C 48 2C 30   ;0900,0180,T,H,0 
35 2C 41 2C 30 3D 31 32 33 34 35 36 37 38 39 30   5,A,0=1234567890 
41 42 43 44 45 7C 7D 00 00 00 00 00 00 00 00 00   ABCDE|}.........  
						

							 
- 26 - Print conditions: 
•  Print width:  Approximately 100 mm 
• Sensor:  Not used 
•  Print speed:  4 ips   
•  A currently selected print mode (thermal transfer/direct thermal) is used. 
•  Data of 16 bytes is printed on one line. 
•  Data is printed, starting from new data to old data. 
•  Data pointed by a receive buffer write pointer is printed in bold type. 
 
Size of receive buffer 
RS-232C:  1 MB (Max. 65536 lines) 
Centronics:  1 MB (Max. 65536 lines) 
Network I/F:  1 MB (Max. 65536 lines) 
BASIC1:  8 KB (Max. 512 lines) 
BASIC2:  8 KB (Max. 512 lines) 
USB:  1 MB (Max. 65536 lines) 
RFID:  8 KB (Max. 512 lines) 
 
NOTES:  
1.  To print all data in a receive buffer, the following label length is required. 
RS-232C: 198.2 m 
Centronics: 198.2 m 
Network I/F:  198.2 m 
BASIC1: 2 m 
BASIC2: 2 m 
USB: 198.2 m 
RFID: 2 m 
 
2.   If an error occurs during printing in receive buffer dump mode, the printer displays an 
error message, then stops.    The error is cleared by pressing the [PAUSE] key, and the 
display is returned to the receive buffer dumping menu “ DUMP MODE”.    After the 
error is cleared, data is not automatically reprinted.   
 
5.11  BASIC EXPANSION MODE 
It is possible to execute the BASIC expansion mode program in BASIC expansion mode under the 
following conditions:   
- The BASIC expansion mode program has already been loaded. 
- The BASIC enable setting mode is selected.   
The basic expansion mode ends when the basic expansion program is exited.  
						

							 
- 27 -
5.12  AUTOMATIC CALIBRATION SETTING   
5.12.1   Operation Example of Automatic Calibration Setting 
     
Power ON    
              
O N  L I N E       (1)  Idling or printing normally 
B - S A 4 T - T       V 1 . 2 A 
              
        [PAUSE] 
 
(2)  Press the [PAUSE] key. 
P A U S E         (3)  “PAUSE” is displayed. 
B - S A 4 T - T       V 1 . 2 A 
              
        [RESTART] 
 
(4)  Hold down the [RESTART] key for 3 seconds 
or more while the printer is in a pause state. 
< 1 > R E S E T          (5)  The reset menu is displayed. 
              
              
        [FEED] 
 
(6)  Press the [FEED] key. 
< 2 > P A R A M E T E R    S E T
             (7)  System mode menu display 
(Parameter setting) 
              
        [FEED] 
 
(8)  Press the [FEED] key. 
< 3 > A D J U S T    S E T 
             (9)  System mode menu display 
(Fine adjustment value setting) 
              
        [FEED] 
 
(10)  Press the [FEED] key. 
< 4 > D U M P    M O D E   
             (11)  The receive buffer dumping menu is displayed.
              
        [FEED] 
 
(12)  Press the [FEED] key. 
< 5 > E X P A N D    M O D E
             (13)  The BASIC expansion mode menu is 
displayed. 
              
        [FEED] 
 
(14)  Press the [FEED] key. 
< 6 > A U T O    C A L I B 
             (15)  The automatic calibration menu is displayed. 
              
        [PAUSE] 
 
(16)  Press the [PAUSE] key.